Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

Description of this part for the microscope.

catalog number 45 29 07 - alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

The tube is universal - there is no difference between the right and left side.

Description of this part for the microscope.

in Zeiss Axioskop 20 microscopes (this head has the catalog number 45 29 07 - alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

VERY IMPORTANT: this is a central prism (beamsplitter). It is neither a left nor a right prism and cannot replace them.

Other commonly used names:
- central prism of the binocular head
- beamsplitter prism
- optical path prism - central
- prism (common)
- angle prism (common)
- cemented prism (common)
- mirror prism (common)
- prism block (common)

Description of this part for the microscope.

head has the catalog number 45 29 07 - alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

Description of this part for the microscope.

(this head has the catalog number 45 29 07 - alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

Description of this part for the microscope.

451393 (45 13 93)
Function: polarizer / analyzer
Compatibility: Zeiss Axiovert 100 / 135 inverted microscopes

If you want to use this slide in another microscope - carefully check the dimensions visible in the photos.

Note - in commonly used terminology there is some inconsistency and foreign as well as incorrect names are often used:
- polaryzator
- polarisator
- polarizer
- polariser
- filtr polaryzacyjny
- filtr POL
- circular polariser
- CPL Filter
- POL filter
- polarisations Filter
- polarization Filter
- anaizator
- analisaor
- Analysator
- POL analizer
- polarization analyser

Description of this part for the microscope.

alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

Note - Please review the photos and dimensions of this item carefully as it is possible that this is not a complete assembly connector.

Description of this part for the microscope.

The set includes a cable Zeiss P/N 452112-9081/X2.

This service part for repair of Zeiss Axiovert 100M microscope may solve the following issues:
- coarse movement does not work in Zeiss Axiovert 100M microscope
- fine movement does not work in Zeiss Axiovert 100M microscope
- where to find original spare parts for Zeiss Axiovert 100

The Zeiss Axiovert 100M microscope shares many components with the non-motorized version (Axiovert 100), so it is possible that this element can also be installed in the non-motorized version, i.e. Axiovert 100.

The photos show dimensions and exact appearance of this element from multiple views. Additionally, the video shows how the mechanism works.

Description of this part for the microscope.

electrical contacts

This service part for repair of Zeiss Axiovert 100M microscope may solve the following issues:
- no image on photo output in Zeiss Axiovert 100 microscope
- damaged image reflecting mirror in Zeiss Axiovert 100
- where to find original spare parts for Zeiss Axiovert 100

The Zeiss Axiovert 100M microscope shares many components with the non-motorized version (Axiovert 100), so it is possible that this element can also be installed in the non-motorized version, i.e. Axiovert 100.

The photos show dimensions and exact appearance of this element from multiple views. Additionally, the video shows how the mechanism works.

Description of this part for the microscope.

the image to the photo output. It also has two electrical contacts.

This service part for repair of Zeiss Axiovert 100M microscope may solve the following issues:
- no image on photo output in Zeiss Axiovert 100 microscope
- damaged image reflecting mirror in Zeiss Axiovert 100
- where to find original spare parts for Zeiss Axiovert 100

The Zeiss Axiovert 100M microscope shares many components with the non-motorized version (Axiovert 100), so it is possible that this element can also be installed in the non-motorized version, i.e. Axiovert 100.

The photos show dimensions and exact appearance of this element from multiple views. Additionally, the video shows how the mechanism works.

Description of this part for the microscope.

controls the shutter. It is not a complete shutter. The module contains:
- a milled aluminium bracket that fits inside the microscope housing
- the Kuhnke D 23 LOL -F 24VDC 100%ED rotary solenoid
- two HOA2001-1 optical sensors
- the wiring and the connector to the Zeiss 451331-9320 board

I was not able to confirm it, but it is possible that this part also fits the inverted Zeiss Axiovert 135M microscope. Before you decide to use the electronic module shown here in the Axiovert 135M model, please check this on forums or groups devoted to Zeiss microscopes.

In the last photos the arrow shows where this part sits in the Zeiss Axiovert 100M microscope, so that you can identify it without any doubt.

Description of this part for the microscope.

sensors and drives in the motorized inverted Zeiss Axiovert 100M microscope are connected.

Markings on the board:
- 451331-9320
- 3320 B
- DL SP1 SP2 SHUT
- SCA
- 3320 L
- Carl Zeiss Jena

ATTENTION: This is a board for a microscope branded by Zeiss (Oberkochen, West Germany). The board, however, carries the "Carl Zeiss Jena" logo. This is not a mistake - this board was made in week 31 of 1997, already after the German reunification, when the Jena plant was producing for the entire Carl Zeiss group.

IMPORTANT: in the photo you can see that in every pin block onto which a connector is plugged, one pin is missing. This is not damage, this is not a broken-off pin - this is the original factory condition. It is supposed to look like this.

I was not able to confirm it, but it is possible that this part also fits the inverted Zeiss Axiovert 135M microscope. Before you decide to use the electronic board shown here in the Axiovert 135M model, please check this on forums or groups devoted to Zeiss microscopes.

In the last photos the arrow shows where this part sits in the Zeiss Axiovert 100M microscope, so that you can identify it without any doubt.

Description of this part for the microscope.

board carrying the two momentary pushbuttons:
- 452112-9036
- S8/10
- 452112-3036 L
- S9/11

Marking on the cable connecting the microswitches: 451331-8094

The connector plugs into the SCA socket on the central distribution board 451331-9320 (https://www.microscopeparts.eu/part/99909).

I was not able to confirm it, but it is possible that these parts also fit the inverted Zeiss Axiovert 135M microscope. Before you decide to use them in the Axiovert 135M model, please check this on forums or groups devoted to Zeiss microscopes.

Description of this part for the microscope.

objectives are corrected for infinity, so an intermediate optic in the form of a tube lens is required to create the intermediate image. In this case it has to be a lens of the Zeiss ICS system with a focal length of 164.5 mm.

In this series of inverted microscopes the tube lens sits below the nosepiece. The last photos in the gallery show the stand of the Carl Zeiss Axiovert 100M microscope, with an arrow pointing to the exact place where this lens is located. This allows you to identify the part without any doubt.

According to the manufacturer this is not a part intended to be replaced by the user, so there is no catalogue number either on the lens mount or on the aluminium profile into which this lens is screwed.

I was not able to confirm it, but it is possible that this ICS tube lens also fits the inverted microscopes Zeiss Axiovert 135 / 135M. Before you decide to use it in the Axiovert 135 / 135M models, please check this on forums or groups devoted to Zeiss microscopes.

Description of this part for the microscope.

The tube transfers the image from the objectives through the whole stand to the head mount. This part has no counterpart in upright biological microscopes.

There is no catalogue number anywhere on this part. That may suggest the manufacturer did not intend it as a part to be replaced by the user, one that could be ordered from service.

The last photos in the gallery show the stand of the Carl Zeiss Axiovert 100M microscope, with an arrow pointing to the place where this part is located. This allows you to identify it without any doubt.

I was not able to confirm it, but it is possible that this tube with optics also fits the inverted microscopes Zeiss Axiovert 135 / 135M. Before you decide to use it in the Axiovert 135 / 135M models, please check this on forums or groups devoted to Zeiss microscopes.

Description of this part for the microscope.

Zeiss
Lettering: white "Zeiss" wordmark in the typeface introduced together with the joint logo of both Zeiss companies (Zeiss Oberkochen and Carl Zeiss Jena) in 1993/94
Material: aluminium, thin sheet with embossed lettering
Colour: the so-called early light blue, used by the manufacturer until 1997
Dimensions: 23 mm x 23 mm
Mounting: the plate is glued on

This is the plate variant with the logo introduced in 1993/94 and in use until 1997: light blue, a square with the lens cut out at the bottom, lettering in rounded letters. You can see the previous version here: https://www.microscopeparts.eu/part/99868.

Because the adhesive that held these plates to the microscope body loses its grip over the years, such plates sometimes fall off. Sometimes they are also deliberately prised out. A plate like this lets you bring your microscope back to its factory appearance using original parts.