Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

from a Leitz Dialux microscope. In the last photo in the gallery you can see the microscope stage from which it was removed. However, the manufacturer fitted the same type of mechanical XY microscope stage to many other Leitz microscope models, so this specimen holder is also compatible with models other than the Leitz Dialux.

When determining compatibility and whether this specimen holder can be mounted on a particular mechanical XY microscope stage, the following dimensions are critical:
- distance between the two side locating pins: 81 mm measured from the outer edge of one pin to the outer edge of the other pin
- locating pin diameter: 3 mm each
- therefore, the centre-to-centre distance between the locating pins is 78 mm
- diameter of the central mounting screw: 4 mm
- position of the mounting screw: centred between the two locating pins

If the spacing of the locating pins matches, this specimen holder can also be mounted on microscope stages made by other manufacturers.

Leitz Wetzlar produced specimen holders with fixed stage clips as well as versions with a spring-loaded stage clip. Here I am showing and offering the spring-loaded version.

On the used market and in technical documentation, this microscope part is described using a variety of names. Common terms include:
- specimen holder
- microscope stage specimen holder
- mechanical stage specimen holder
- slide holder
- microscope slide holder
- microscope slide clamp
- spring-loaded specimen holder
- spring-loaded slide holder
- spring-loaded stage clip
- specimen clamp
- specimen carrier
- mechanical stage carrier
- XY stage specimen holder
- specimen holder for mechanical XY microscope stage
- stage holder
- stage clip assembly

The photographs in the gallery show the exact dimensions of the microscope part offered here. In addition, the last photograph includes an arrow indicating exactly which microscope part is being described and where it is mounted on the mechanical XY microscope stage, making identification straightforward. The accompanying video demonstrates the operation of the spring-loaded stage clip.

Description of this part for the microscope.

allowing precise movement of the specimen in both the X and Y axes of the stage plane. The manipulator consists of two coaxial knobs, two independent drive shafts and the fixing elements that attach it to the stage mechanism.

This particular manipulator was removed from a Leitz Dialux microscope. The last photograph in the gallery shows the entire microscope stage from which it was dismounted. The manufacturer also used the same or very similar stages in many other Leitz Wetzlar microscope models, which is why the manipulator may also be compatible with other models from this company.

On the second-hand market and in service documentation one encounters many names referring to this assembly. The most commonly used terms include, among others:
- stage manipulator
- XY stage manipulator
- mechanical stage drive
- stage control knobs
- specimen mover
- coaxial stage drive
- stage drive assembly
- mechanical stage control
- manual XY stage drive
- stage actuator mechanism

Such manipulators very often suffer mechanical damage during transport of the microscope. Because they protrude beyond the outline of the stand, it is precisely they that absorb the impact energy first - in the event of a fall or improper packaging of the instrument.

In many cases it is not the entire manipulator that is damaged, but only one of its components. Most often these are the knobs, the drive shafts, the coaxial sleeves or the fixing elements. For this reason, this database also contains all the most important constituent parts of this (and other) manipulators, offered separately as service elements.

Damage to the manipulator does not make further work with the microscope impossible. The specimen can be moved by hand, or a simple specimen holder without an XY movement mechanism can be fitted. Such a solution works well at low magnifications; however, when working with objectives of magnifications greater than 40x (e.g. 60x, 63x, 80x or 100x), precise manual movement of the specimen becomes very difficult. At total magnifications exceeding about 400x, even a slight movement of the hand shifts the image by a considerable distance within the field of view. The mechanical manipulator enables very smooth, controlled and repeatable movement of the specimen in both axes, which is particularly important during observation with oil immersion and when producing photographic documentation.

The photographs in the gallery show the exact dimensions of the complete manipulator. The last photograph presents the entire microscope stage together with an arrow indicating the mounting location of this element, which makes it possible to identify the offered part unambiguously.

Description of this part for the microscope.

Wetzlar binocular head P/N 512821/20 (also written 512 821) - but exactly the same tube is used in other models of binocular and trinocular heads as well.

The same front panel design is found in, among others, the Leitz 512 923/20 and Leitz 512 815 trinocular heads - this tube with diopter adjustment will most likely fit those too.

Diameter of the eyepieces it takes: 23.2 mm.

In the Leitz bino 512821/20 both the left and the right tube have diopter adjustment. They are mechanically identical parts - there is no difference between the left and the right tube. They can be swapped.

Before you decide to use this tube in a Leitz Wetzlar head other than model 512 821/20, first compare the exact dimensions (the photos show a millimetre scale), and if you have any doubts, ask in internet groups and forums.

This is a service part for a microscope head - not for a specific microscope model. Such a head can be mounted on many Leitz Wetzlar microscope models (and even on microscopes from other makers), so no list of microscopes this tube fits can be given - it fits the head, and the user mounts the head wherever he wants.

In the "compatibility" section I list a few example Leitz Wetzlar microscope models that turn up on the second-hand market complete with the head this tube comes from - but this is definitely not a complete list. They include:
- Leitz Wetzlar Dialux 20 / Dialux 22 EB
- Leitz Wetzlar Laborlux K / Laborlux S
- Leitz Wetzlar Diaplan

On the last photos in the gallery you can see the Leitz Wetzlar 512821/20 binocular head taken apart, with an arrow pointing to which part this is and where it sits in the head. That makes it unambiguous to identify.

Description of this part for the microscope.

of:
- two brass carrier plates, each with a round seat for the eyepiece tube (it is to these plates that the tubes https://www.microscopeparts.eu/part/99928 are screwed)
- a central scissor lever made of plastic, with its fixing screw
- two pressure springs (one for each brass plate)

Turning the central lever moves both brass plates outwards symmetrically. It is exactly this constant work of the plastic central lever against the brass plates that wears the plastic lever out - and then it has to be replaced.

This mechanism was removed from the Leitz Wetzlar binocular head P/N 512821/20 (also written 512 821) - but exactly the same one is used in other models of binocular and trinocular heads as well.

The same front panel design is found in, among others, the Leitz 512 923/20 and Leitz 512 815 trinocular heads - this interpupillary mechanism will most likely fit those too.

From the outside this mechanism is covered by plastic covers - one on the right (https://www.microscopeparts.eu/part/99931) and a different one on the left (https://www.microscopeparts.eu/part/99930). These plastic covers carry a printed scale on which the interpupillary distance is read.

Before you decide to use this mechanism in a Leitz Wetzlar head other than model 512 821/20, first compare the exact dimensions (the photos show a millimetre scale), and if you have any doubts, ask in internet groups and forums.

This is a service part for a microscope head - not for a specific microscope model. Such a head can be mounted on many Leitz Wetzlar microscope models (and even on microscopes from other makers), so no list of microscopes this mechanism fits can be given - it fits the head, and the user mounts the head wherever he wants.

In the "compatibility" section I list a few example Leitz Wetzlar microscope models that turn up on the second-hand market complete with the head this mechanism comes from - but this is definitely not a complete list. They include:
- Leitz Wetzlar Dialux 20 / Dialux 22 EB
- Leitz Wetzlar Laborlux K / Laborlux S
- Leitz Wetzlar Diaplan

On the last photos in the gallery you can see the Leitz Wetzlar 512821/20 binocular head, and with arrows I try to show which part this is and where it sits in the head.

Description of this part for the microscope.

internal interpupillary distance adjustment mechanism from the front (https://www.microscopeparts.eu/part/99929). The second, left cover is shaped differently and is a separate item (https://www.microscopeparts.eu/part/99930).

There is no printing on the right cover - the interpupillary scale is printed on the left cover. When the interpupillary distance is changed, the right cover covers or uncovers part of the left cover and with it part of the scale placed there - and this is how the interpupillary distance value is read.

The cover is made of plastic and is screwed with four screws directly to the brass carrier plate, to which the eyepiece tube (https://www.microscopeparts.eu/part/99928) is also fastened.

This cover was removed from the Leitz Wetzlar binocular head P/N 512821/20 (also written 512 821) - but exactly the same one is used in other models of binocular and trinocular heads as well.

The same front panel design is found in, among others, the Leitz 512 923/20 and Leitz 512 815 trinocular heads - this cover will most likely fit those too.

Before you decide to use this cover in a Leitz Wetzlar head other than model 512 821/20, first compare the exact dimensions (the photos show a millimetre scale), and if you have any doubts, ask in internet groups and forums.

This is a service part for a microscope head - not for a specific microscope model. Such a head can be mounted on many Leitz Wetzlar microscope models (and even on microscopes from other makers), so no list of microscopes this cover fits can be given - it fits the head, and the user mounts the head wherever he wants.

In the "compatibility" section I list a few example Leitz Wetzlar microscope models that turn up on the second-hand market complete with the head this cover comes from - but this is definitely not a complete list. They include:
- Leitz Wetzlar Dialux 20 / Dialux 22 EB
- Leitz Wetzlar Laborlux K / Laborlux S
- Leitz Wetzlar Diaplan

On the last photos in the gallery you can see the Leitz Wetzlar 512821/20 binocular head, and with arrows I try to show which part this is and where it sits in the head.

Description of this part for the microscope.

covers that close the internal interpupillary distance adjustment mechanism from the front (https://www.microscopeparts.eu/part/99929). The second, right cover is shaped differently and is a separate item (https://www.microscopeparts.eu/part/99931).

The interpupillary scale is printed on the left cover - there is no printing on the right cover. When the interpupillary distance is changed, the right cover covers or uncovers part of the left cover and with it part of the scale placed there - and this is how the interpupillary distance value is read.

The cover is made of plastic and is screwed with four screws directly to the brass carrier plate, to which the eyepiece tube (https://www.microscopeparts.eu/part/99928) is also fastened.

This cover was removed from the Leitz Wetzlar binocular head P/N 512821/20 (also written 512 821) - but exactly the same one is used in other models of binocular and trinocular heads as well.

The same front panel design is found in, among others, the Leitz 512 923/20 and Leitz 512 815 trinocular heads - this cover will most likely fit those too.

Before you decide to use this cover in a Leitz Wetzlar head other than model 512 821/20, first compare the exact dimensions (the photos show a millimetre scale), and if you have any doubts, ask in internet groups and forums.

This is a service part for a microscope head - not for a specific microscope model. Such a head can be mounted on many Leitz Wetzlar microscope models (and even on microscopes from other makers), so no list of microscopes this cover fits can be given - it fits the head, and the user mounts the head wherever he wants.

In the "compatibility" section I list a few example Leitz Wetzlar microscope models that turn up on the second-hand market complete with the head this cover comes from - but this is definitely not a complete list. They include:
- Leitz Wetzlar Dialux 20 / Dialux 22 EB
- Leitz Wetzlar Laborlux K / Laborlux S
- Leitz Wetzlar Diaplan

On the last photos in the gallery you can see the Leitz Wetzlar 512821/20 binocular head, and with arrows I try to show which part this is and where it sits in the head.