Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

apertures. This allows the use of a darkfield condenser with an aperture diaphragm.

Description of this part for the microscope.

consists of:
- an illuminator (light source)
- a "tube" containing collimating lenses and a field diaphragm
- a 90-degree angle mirror
- a light filter (clear or blue)

This offers an integrated block, also known as a "tube." It consists of:
- a metal tube with holes that acts as a heat sink, dissipating heat from the light source
- a set of lenses that collimate the illumination beam
- a field diaphragm (iris diaphragm)
- a knob that opens/closes the diaphragm

This element is the same for all lighting types, regardless of whether it's a 6V 15W bulb, a PZO OH1 (12V 100W) or a modified LED, so it fits any version of the PZO Biolar microscope:
- B
- B2
- GF
- Pol
- DIC
- EPI
- Fluoreszenz

It contains two critical components: a collimating lens that often cracks under temperature, and a field diaphragm whose blades are prone to bending.

If you need smaller - individual components from this block - contact us

Description of this part for the microscope.

without the collimating lenses.

This component is the same for all versions of the PZO Biolar microscope:
- B
- B2
- GF
- Pol
- DIC
- EPI
- Fluoreszenz

If you need smaller, individual diaphragm components (e.g., separate blades) - contact us

Description of this part for the microscope.

30S microscope base consists of:
- an illuminator (light source)
- a "tube" containing a collimating lens and a field diaphragm
- a screw securing the tube
- an angle mirror that reflects light at 90 degrees

Two components of this tube are offered here:
- a metal tube with a lens collimating the illumination beam
- a metal tube with a field diaphragm (iris diaphragm)

There are two critical components here: the collimating lens, which often cracks under temperature, and the field diaphragm, whose blades are prone to bending.

Description of this part for the microscope.

condensers:
- PZO K3Ph
- PZO K3Ph1
- PZO K4Ph
- PZO KS (this is the "stereo contrast" condenser sold with PZO MB30S microscopes. There are no(!) markings or numbers whatsoever on this condenser)

The diaphragm blades themselves, which are located inside this module, also fit the diaphragms installed in the following condensers:
- PZO K3PhZ (variable phase contrast)
- PZO KPI2 (condenser for Pluta DIC)

Mechanically, this diaphragm is screwed onto the lower part of the phase contrast condenser. The housing of the diaphragm module has a 32 mm male thread. The complete diaphragm with its housing has a diameter of 52 mm.

The iris diaphragm is damaged very often. Replacing it can solve the following problems:
- when the small lever used to open and close the diaphragm blades breaks off. This is a common failure, because this lever is a thin sheet made of a brittle alloy
- when the diaphragm blades get damaged, bent or broken. This is one of the most common faults in microscopes
- when the diaphragm blades jump out of their mounting grooves and you cannot reassemble them
- when the diaphragm stops opening and closing and is completely seized. This happens when the grease has dried out or rust has glued the blades together

The last photos in the gallery show the PZO KS condenser, with an arrow indicating where this diaphragm is located inside the condenser. This allows the component to be identified unambiguously.

PZO phase contrast condensers are often fitted in microscopes from manufacturers other than PZO, so the component presented here is not a repair part for one specific microscope model. This diaphragm will help to repair a phase contrast condenser - regardless of which microscope model and which manufacturer it works in.