Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

objective
Manufacturer name: Epi-Objektiv 18x/0.30 Trockensystem Tubus unendlich, 1940
Name used before 1940: Epi-Objektiv 9.7 Epi, 18 Met Trockensystem Tubus unendlich, 1937
Thread: due to measurement inaccuracy I provide: 11 mm or 11.5 mm
Additional: the objective includes an insert that fits the EPI illuminator
Magnification (so called magnifier magnification): 18x
Numerical aperture: 0.30
Oil immersion: NO (dry objective)
Focal length: 13.8 mm

Compatibility:
- Carl Zeiss Jena EPI reflected light condenser W
- Carl Zeiss Jena EPI reflected light condenser WK
- Carl Zeiss Jena Metalliput metallurgical microscope
- Carl Zeiss Jena Met Mi IX metallurgical microscope

This unusual objective has a narrow special thread, but with the use of an intermediate ring with correction lens it can also be used on a standard microscope stand (e.g. Carl Zeiss Jena Lg).

When this objective is used on the Carl Zeiss Jena Metalliput microscope with an infinity corrected tube (in practice the tube length there is 250 mm), the full magnification of 18x is obtained.
When this objective is used together with a reflected light condenser (with an additional intermediate lens in the tube, that is with a 160 mm tube length) the concave mirrors partially extend under the objective, therefore the free working distance cannot be fully utilized. In such a configuration the real magnification is about two times smaller, approximately 9.7x.

Epi / Met objectives produced in the years 1937-1939 have two numbers engraved on the housing: 9.7 Epi, 18 Met.
a) the smaller value applies when used with the EPI condenser (correction lens focal length = 160 mm)
b) the larger value applies to the magnification obtained when the objective is used with the metallurgical microscope (correction lens focal length = 250 mm).
In 1940 the method of marking magnification on the objective housing was changed and only the "magnifier magnification" and the numerical aperture value were provided.

Information: the source of this information is the website of the Zeiss company archive. This information is provided in order to spread knowledge about rarely encountered microscope elements.

Description of this part for the microscope.

objective
Manufacturer name: Epi-Objektiv 30x/0.40 Trockensystem Tubus unendlich, 1940
Name used before 1940: Epi-Objektiv 16/0.40 Trockensystem Tubus unendlich, 1937
Thread: due to measurement inaccuracy I provide: 11 mm or 11.5 mm
Additional: the objective includes an insert that fits the EPI illuminator
Magnification (so called magnifier magnification): 30x
Numerical aperture: 0.40
Oil immersion: NO (dry objective)
Focal length: 8,1 mm

Compatibility:
- Carl Zeiss Jena EPI reflected light condenser W
- Carl Zeiss Jena EPI reflected light condenser WK
- Carl Zeiss Jena Metalliput metallurgical microscope
- Carl Zeiss Jena Met Mi IX metallurgical microscope

This unusual objective has a narrow special thread, but with the use of an intermediate ring with correction lens it can also be used on a standard microscope stand (e.g. Carl Zeiss Jena Lg).

When this objective is used on the Carl Zeiss Jena Metalliput microscope with an infinity corrected tube (in practice the tube length there is 250 mm), the full magnification of 30x is obtained.
When this objective is used together with a reflected light condenser (with an additional intermediate lens in the tube, that is with a 160 mm tube length) the concave mirrors partially extend under the objective, therefore the free working distance cannot be fully utilized. In such a configuration the real magnification is about two times smaller, approximately 16x.

Epi / Met objectives produced in the years 1937-1939 have two numbers engraved on the housing: 16 Epi, 30 Met.
a) the smaller value applies when used with the EPI condenser (correction lens focal length = 160 mm)
b) the larger value applies to the magnification obtained when the objective is used with the metallurgical microscope (correction lens focal length = 250 mm).
In 1940 the method of marking magnification on the objective housing was changed and only the "magnifier magnification" and the numerical aperture value were provided.

Information: the source of this information is the website of the Zeiss company archive. This information is provided in order to spread knowledge about rarely encountered microscope elements.

Description of this part for the microscope.

objective
Manufacturer name: Epi-Objektiv 34/0.60 Trockensystem Tubus unendlich, 1939
Name used after 1940: Epi-Objektiv 60x/0.60 Trockensystem Tubus unendlich, 1940
Model: 62 0,60 Met / 34 0,60 Epi
Thread: due to measurement inaccuracy I provide: 11 mm or 11.5 mm
Additional: the objective includes an insert that fits the EPI illuminator
Magnification (so called magnifier magnification): 62x
Numerical aperture: 0.60
Oil immersion: NO (dry objective)
Focal length: 4,1 mm

Compatibility:
- Carl Zeiss Jena EPI reflected light condenser W
- Carl Zeiss Jena EPI reflected light condenser WK
- Carl Zeiss Jena Metalliput metallurgical microscope
- Carl Zeiss Jena Met Mi IX metallurgical microscope

This unusual objective has a narrow special thread, but with the use of an intermediate ring with correction lens it can also be used on a standard microscope stand (e.g. Carl Zeiss Jena Lg).

When this objective is used on the Carl Zeiss Jena Metalliput microscope with an infinity corrected tube (in practice the tube length there is 250 mm), the full magnification of 62x is obtained.
When this objective is used together with a reflected light condenser (with an additional intermediate lens in the tube, that is with a 160 mm tube length) the concave mirrors partially extend under the objective, therefore the free working distance cannot be fully utilized. In such a configuration the real magnification is about two times smaller, approximately 34x.

Epi / Met objectives produced in the years 1937-1939 have two numbers engraved on the housing: 62 0,60 Met / 34 0,60 Epi.
a) the smaller value applies when used with the EPI condenser (correction lens focal length = 160 mm)
b) the larger value applies to the magnification obtained when the objective is used with the metallurgical microscope (correction lens focal length = 250 mm).
In 1940 the method of marking magnification on the objective housing was changed and only the "magnifier magnification" and the numerical aperture value were provided.

Information: the source of this information is the website of the Zeiss company archive. This information is provided in order to spread knowledge about rarely encountered microscope elements.

Description of this part for the microscope.

250 series microscopes.
Note that this element is a component of a microscope element (the angled tube) and not a part dedicated to a specific microscope model.

This element fits, among others, the following Carl Zeiss Jena microscopes from the CF-250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenavert
- Jenatech
- Jenapol

Important: the element DOES NOT INCLUDE the screw used to secure the microscope head.

Inside this element there is a protective glass (without its own magnification, so called "zero lens") with a violet anti-reflection coating.
Although this holder for the binocular microscope head and the holder located at the photographic port look the same, have the same dimensions and are mechanically compatible - they are NOT (!) identical.
- the binocular microscope head mount contains a protective glass with a violet anti-reflection coating
- the mount located at the photographic port contains a protective glass with a green anti-reflection coating.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

250 series microscopes.
Note that this element is a component of a microscope element (the angled tube with photo port) and not a part dedicated to a specific microscope model.

This element fits, among others, the following Carl Zeiss Jena microscopes from the CF-250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenavert
- Jenatech
- Jenapol

Important: the element DOES NOT INCLUDE the screw used to secure the microscope head.

Inside this element there is a protective glass (without its own magnification, so called "zero lens") with a green anti-reflection coating.
Although this holder at the photographic port and the holder for the binocular microscope head look the same, have the same dimensions and are mechanically compatible - they are NOT (!) identical.
- the binocular microscope head mount contains a protective glass with a violet anti-reflection coating
- the mount located at the photographic port contains a protective glass with a green anti-reflection coating.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

allows correction of vision in one eye and proper adjustment of image focus.

Basic parameters:
- Type: tube with diopter correction ring
- Diameter of supported eyepieces: 30 mm
- Color: white

Fits 30 mm heads used, among others, in the following Carl Zeiss Jena microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

Description of this part for the microscope.

they were used in Spekol devices. Definitely better quality than inexpensive Chinese cuvettes.

Description of this part for the microscope.

logo
- knobs operating the internal mechanism
- gear assembly forming the fine focus mechanism (it can be removed because it is a replaceable microscope element)

The entire block fits the Carl Zeiss Jena Lg microscope (from the L-Stativ group), however the fine focus mechanism inside can be unscrewed and as far as I know (to the best of my knowledge) it also fits the microscopes:
- Carl Zeiss Jena Lr
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lumipan

Description of this part for the microscope.

Jena microscope models whose name ends with "-val", for example:
- Laboval
- Ergaval
- Amplival

Description of this part for the microscope.

were used to sell phase contrast sets for (among others) the following Carl Zeiss Jena microscopes:
- Lg
- Lumipan
- Nf

Description of this part for the microscope.

Ergaval microscope has two centering screws. The offer concerns a single centering screw.

The last photo in the gallery clearly shows with an arrow which element is being offered.

Description of this part for the microscope.

is being offered.

Fits among others the following Carl Zeiss Jena microscope models:
- Lumipan
- Lg
- Lr
- Lu

Note - production of the L-Stativ series microscopes began before World War II and continued into the 1950s. Over the years, small design details changed, including the method of mounting the microscope head.
- the earliest models had a threaded microscope head, and there was no fixing screw at all
- the latest models already featured an advanced mounting system with a spring screw (you can see it in the database under number 00659)

Description of this part for the microscope.

second half of the 1970s. It's quite possible they were used in Spekol devices. Definitely better quality than inexpensive Chinese cuvettes.

Description of this part for the microscope.

half of the 1970s. It's quite possible they were used in Spekol devices. Definitely better quality than inexpensive Chinese cuvettes.

Description of this part for the microscope.

they were used in Spekol devices. Definitely better quality than inexpensive Chinese cuvettes.

Description of this part for the microscope.

It's quite possible it was used in Spekol devices. Definitely better quality than inexpensive Chinese cuvettes.

Description of this part for the microscope.

The last photo shows which element is being offered.

Fits among others the following Carl Zeiss Jena microscope models:
- Lumipan
- Lg
- Lr
- Lu

Note - production of the L-Stativ series microscopes began before World War II and continued into the 1950s. Over the years, small design details changed, including the method of mounting the microscope stage. Microscope models that have a non-removable stage (screwed to the stand) do not have and do not need such a spring screw.

Description of this part for the microscope.

4 mo2 condenser holder that was used in the Carl Zeiss Jena Ergaval microscope. The same condenser (but with a different lower lens) is used in an identical holder in Fluoval microscopes. Condenser holders with such screws can also be found in the following microscopes:
- Docuval
- Amplival
- NU-2

The purpose of this spring screw is to push the clamp in which the condenser is mounted outward. Thanks to the spring integrated in the screw, it is possible to center the condenser using long centering screws (you can find such a centering screw in the database under number 99132).

In the last photo, an arrow clearly indicates which screw is meant and where it is mounted in the condenser holder.

Description of this part for the microscope.

that was used in the Carl Zeiss Jena Ergaval microscope. The same condenser (but with a different lower lens) is used in an identical holder in Fluoval microscopes. Condenser holders with such screws can also be found in the following microscopes:
- Docuval
- Amplival
- NU-2

In the last photo, an arrow clearly indicates which screw is meant and where it is mounted in the condenser holder.

Description of this part for the microscope.

assembly of two lenses
- knob for moving and shifting the lenses
- mechanism for moving and shifting the lenses

Metal, cast or injection-molded parts manufactured by Carl Zeiss Jena have their own identification numbers. In this mechanism the lens is mounted on a cast part marked with number 2582 (full marking: Si10 CZ 2582).

This is a service element (repair part) of the trinocular head (photo tube), suitable for Carl Zeiss Jena microscopes of the CF-250 series. Please note that this is an element (component) of a microscope part (German: "Fototubus") and not a part dedicated to a specific microscope model.

Carl Zeiss Jena microscopes of the CF-250 series have a modular design and the microscope part to which the eyepieces are mounted (commonly referred to as "head", "binocular" or "twin tube") is a separate element from the angle tube (sometimes the German term "Winkeltubus" is used). If the angle tube has a photographic output, it is referred to as a "photo tube". The Bertrand lens offered and described here is intended specifically for this microscope part.

Hinweis - Carl Zeiss Jena microscopes Jenapol and Jenatech, although they also belong to the CF-250 series, have a differently designed photographic output and this mechanism DOES NOT FIT these models.

Hinweis - Carl Zeiss Jena also produced a simplified version of the photo tube which does not contain a Bertrand lens inside. In the image gallery there is also a page from the manufacturer's catalog so that it is visible whether these versions differ externally in appearance. This Bertrand lens shown and offered here CANNOT be installed in such a simplified version of the photo tube.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is concerned and where it is located in the head, in order to clearly identify this part.

In common usage many names are used for the photo tube. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trinocular head
- trinocular microscope head
- trinocular head assembly
- photo dome
- inclined tube with photo output

Description of this part for the microscope.

Manufacturer: Carl Zeiss
Name: POL analyzer for simple polarization
Intended for: monocular biological microscopes
Type: for use with transmitted or reflected light

Hinweis: Please check whether the eyepiece diameter is suitable in order to mount the analyzer onto it. The dimensions of the analyzer housing are visible in the photos, and the housing also has a certain tolerance range.

Description of this part for the microscope.

however, no light source is included in the set.
- A stage with top mounting or with side guide rails can be installed on this base
- There is a rack on the stand

This heavy, stable stand is often used for applications completely unrelated to microscopes, for example for mounting drills, lasers or hardness testers.

Description of this part for the microscope.

molded parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the number 2580 (full designation: Si10 CZ 2580).

This is a service element (replacement part) for the trino head (head with photo output), suitable for Carl Zeiss Jena CF-250 microscopes. Please note that this is a microscope element for a microscope part (the trinocular head) and not a part for a specific microscope model.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the upper main part of the housing is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this housing DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the head, in order to clearly identify this part.

Many different names are commonly used for the trino head. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trino head
- trinocular head
- trinocular head unit
- photo dome
- photo tube
- inclined tube with photo output

Description of this part for the microscope.

451393 (45 13 93)
Function: polarizer / analyzer
Compatibility: Zeiss Axiovert 100 / 135 inverted microscopes

If you want to use this slide in another microscope - carefully check the dimensions visible in the photos.

Note - in commonly used terminology there is some inconsistency and foreign as well as incorrect names are often used:
- polaryzator
- polarisator
- polarizer
- polariser
- filtr polaryzacyjny
- filtr POL
- circular polariser
- CPL Filter
- POL filter
- polarisations Filter
- polarization Filter
- anaizator
- analisaor
- Analysator
- POL analizer
- polarization analyser

Description of this part for the microscope.

coarse adjustment knobs and the gear rack on the microscope arm.

Description of this part for the microscope.

catalog number 45 29 07 - alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

The tube is universal - there is no difference between the right and left side.

Description of this part for the microscope.

Most often this occurs when:
- the lubricant in the diaphragm opening / closing mechanism dries out and the user tries to move it by force
- a foreign object gets between the blades (e.g. a glass fragment from a chipped microscope slide)
- the diaphragm is closed too quickly or opened too far

In the event of an iris diaphragm failure, it is possible to:
- replace the entire condenser
- replace only the diaphragm
- repair the diaphragm by replacing the damaged blades

This is an element for repair of a microscope condenser by Carl Zeiss Jena, model Abbe 1.2.
Please note that this is an element (component) for a microscope part (condenser), not for a specific microscope model.

Description of this part for the microscope.

in Zeiss Axioskop 20 microscopes (this head has the catalog number 45 29 07 - alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

VERY IMPORTANT: this is a central prism (beamsplitter). It is neither a left nor a right prism and cannot replace them.

Other commonly used names:
- central prism of the binocular head
- beamsplitter prism
- optical path prism - central
- prism (common)
- angle prism (common)
- cemented prism (common)
- mirror prism (common)
- prism block (common)

Description of this part for the microscope.

head has the catalog number 45 29 07 - alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

Description of this part for the microscope.

(this head has the catalog number 45 29 07 - alternative notation: 452907) as well as in inverted microscopes Zeiss Axiovert 100. It is very likely that the same head was also installed in other microscope models, e.g. Zeiss Axioskop 50 and others.

Description of this part for the microscope.

Jenalumar 50

Please note the following:
- both microscopes listed here use this illuminator for EPI fluorescence, i.e. reflected light. This is not transmitted-light fluorescence.
- this illuminator requires a Carl Zeiss Jena SH 50 power supply for operation
- the Carl Zeiss Jena Jenalumar microscope was produced in two variants - this illuminator fits the Jenalumar version with two small, separate illumination modules
- information can be found on the Internet claiming that this illuminator is suitable for Carl Zeiss Jena Jenavert microscopes. This is NOT correct.
- an HBO lamp is not the same as an XBO lamp.
- Jenamed microscopes other than the "Fluorescence" version have a differently mounted head and this illuminator CANNOT be installed on them.

Important - operating used, overheated HBO lamps, lamps with unknown operating time or from an uncertain source may result in explosion, damage to the illuminator, contamination of the room and a risk to the user's life and health. For this reason, this illuminator DOES NOT INCLUDE a light source (i.e. it does not include the HBO mercury burner).

Description of this part for the microscope.

transmitted light
- precise adjustment in two axes
- rotating stage center with scale (accuracy: 0.1 degree)
- built-in electronic measuring sensors enabling position display on a dedicated readout unit (not included)
- position locking screws (movement lock)

The Carl Zeiss Jena BK 70x50 microscope is one of the most versatile small toolmakers microscopes. Its fully modular design and a wide range of accessories allow it to be configured as a workshop microscope, measuring microscope, for Schlieren observation, metallurgical use, or even biological applications. This stage is one of many options for expanding the BK 70x50 microscope.

Description of this part for the microscope.

element (component) for a microscope part (condenser), not for a specific microscope model.

Description of this part for the microscope.

model Abbe 1.2.
Please note that this is an element (a subcomponent) for a microscope part (the condenser) and not for a specific microscope model.

Description of this part for the microscope.

inserted.

This is an element for repair of a microscope condenser by Carl Zeiss Jena, model Abbe 1.2.
Please note that this is an element (component) for a microscope part (condenser), not for a specific microscope model.

The handle in this ring breaks very frequently, and then the iris diaphragm cannot be opened or closed and the condenser loses its functionality. In such a case, instead of replacing the entire condenser, it is enough to replace only this element - that is, to repair the condenser (recommendation: always repair - never throw away).

Note - over the years Carl Zeiss Jena produced the Abbe 1.2 condenser in different versions, and this ring is available in at least two variants:
- ring with a thickness of 2.5 mm and a handle width of 6 mm
- ring with a thickness of 2 mm and a handle width of 3.5 mm

Here I present and offer a ring with a thickness of 2.5 mm and a handle width of 6 mm. Be sure to check whether this is exactly the ring you need.

Description of this part for the microscope.

are inserted.

This is an element for repair of a microscope condenser by Carl Zeiss Jena, model Abbe 1.2.
Please note that this is an element (component) for a microscope part (condenser), not for a specific microscope model.

The handle in this ring breaks very frequently, and then the iris diaphragm cannot be opened or closed and the condenser loses its functionality. In such a case, instead of replacing the entire condenser, it is enough to replace only this element - that is, to repair the condenser (recommendation: always repair - never throw away).

Note - over the years Carl Zeiss Jena produced the Abbe 1.2 condenser in different versions, and this ring is available in at least two variants:
- ring with a thickness of 2.5 mm and a handle width of 6 mm
- ring with a thickness of 2 mm and a handle width of 3.5 mm

Here I present and offer a ring with a thickness of 2 mm and a handle width of 3,5 mm. Be sure to check whether this is exactly the ring you need.

Description of this part for the microscope.

repair or upgrade of a microscope condenser by Carl Zeiss Jena, model Abbe 1.2.
Please note that this is an element (component) for a microscope part (condenser), not for a specific microscope model.

The Carl Zeiss Jena Abbe 1.2 condenser is available in the following versions:
- with a wide-field lens mounted at the bottom of the condenser, below the filter holder
- with a filter holder only, without a wide-field lens

With this lens, you can upgrade your condenser if it is not equipped with one.

Description of this part for the microscope.

colorless filter is placed (presumably "zero glass").

This particular specimen comes from a Zeiss Universal microscope, but Zeiss uses the same slide standard in other models as well, e.g., Photomicroscope (Phomi) and Ultraphot.

These slides were produced in various versions, differing in minor details but with no difference in function.

Description of this part for the microscope.

colorless filter is placed (presumably "zero glass").

This particular specimen comes from a Zeiss Universal microscope, but Zeiss uses the same slide standard in other models as well, e.g., Photomicroscope (Phomi) and Ultraphot.

These slides were produced in various versions, differing in minor details but with no difference in function.

Description of this part for the microscope.

microscopes.

Description of this part for the microscope.

polarized transmitted light with the possibility of use as a brightfield condenser
Mounting: the condenser is permanently integrated with a dovetail mount
Top lens: flip-out system allowing the upper lens to be moved into or out of the optical path to change the numerical aperture
Iris diaphragm: yes
Diffuser: yes, with the possibility of moving it into or out of the optical path
Polarizer: yes, rotatable, with the possibility of moving it into or out of the optical path

This condenser fits the following Carl Zeiss Jena microscope models:
- Polmi-A
- Nf
- Ng
- Nu / Nu2

Note: despite the visual similarity of the mounting interface, this condenser does NOT fit the Carl Zeiss Jena Lu microscope.

Important: the condenser is permanently integrated with the dovetail mount and cannot be used with other microscopes without significant modifications.

Description of this part for the microscope.

millimeter scale.

The XY cross mechanism is used for precise movement of the specimen slide on the microscope stage.

Basic versions of Carl Zeiss Jena microscopes are equipped with simple stages with clips that hold the specimen. For this reason, at magnifications above 400x, manual movement of the specimen slide becomes very difficult. This is exactly the purpose of cross stage attachments - to allow very precise movement of the specimen, for example at higher magnifications.

This is not a cheap plastic cross stage attachment - it is a solidly built Carl Zeiss Jena construction, highly sought after on the used microscope market.

Note - if the mounting pin spacing matches, this cross mechanism can be installed on microscope stages of virtually any manufacturer.

Note - Carl Zeiss Jena produced cross mechanisms both with fixed specimen clips and with a spring-loaded clip. The version offered here has fixed clips without a spring.

Description of this part for the microscope.

produced several types of sliders with different dimensions and shapes; for example, for Jenamed series microscopes there are at least six versions. Always carefully check the slider dimensions to make sure this is exactly the version you need.

Description of this part for the microscope.

This mounting screw fits most Carl Zeiss Jena microscopes of the CF250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenapol
- Jenatech
- Jenavert

Carl Zeiss Jena developed a complete modular microscope system based on connections using this type of screw. Therefore, this screw as a service part is also compatible with most accessories, modules and microscope elements that can be mounted to the microscope, including:
- magnification changers
- VIS analyzers
- trinocular heads
- Interphako heads

Important - carefully check the shape and dimensions of the screw to make sure it is the size you need. For example, the modular design of the Carl Zeiss Jena Amplival microscope is based on mounting screws of a different shape and size (search for it in this database to have a comparison).

Description of this part for the microscope.

into the slot located above the objective turret and below the microscope head.

Note - Carl Zeiss Jena produced several types of sliders with different dimensions and shapes. For Jenamed series microscopes there are at least six versions. Always carefully check the slider dimensions to make sure this is exactly the type you need. A millimeter scale is shown in each photo.

Description of this part for the microscope.

CZ

This is a slider inserted into the slot located above the objective turret and below the microscope head.

Note - Carl Zeiss Jena produced several types of sliders with different dimensions and shapes. For Jenamed series microscopes there are at least six versions. Always carefully check the slider dimensions to make sure this is exactly the type you need. A millimeter scale is shown in each photo.

Description of this part for the microscope.

stage and under the condenser, e.g. for discs used for phase contrast or darkfield
- three smaller sliders fit into three additional slots between the objective turret and the head (e.g. Pol analyzer, quartz ROT I and quarter-wave plate)

Note - Carl Zeiss Jena produced several types of sliders with different dimensions and shapes. There are at least six variants for microscopes of the Jenamed series. Always carefully check the slider dimensions to make sure this is the exact type you need. A millimeter scale is shown in each photo.

Description of this part for the microscope.

Jenalumar microscope.
This element has fins that function as a heat sink for heat dissipation.

Description of this part for the microscope.

the microscope arm
- and a mounting screw

The mounting screw itself - as a separate component - fits practically most Carl Zeiss Jena microscopes based on the Amplival system:
- Amplival
- Amplival Interphako
- Amplival Pol
- Vertival
- Peraval
- Fluoval
- Docuval

Carl Zeiss Jena developed a complete modular microscope system based on connections made with this type of screw. Thanks to this design, the screw as a service part is also compatible with most accessories, modules and components that can be mounted to the microscope, including:
- EPI arms
- Parktaric Zoom Tube module
- Interphako heads

Important - carefully check the shape and dimensions of the screw to make sure it is the size you need. For example, the modular design of the Carl Zeiss Jena Jenamed microscope is based on mounting screws of a different shape and size (search for it in this database for comparison).

Description of this part for the microscope.

This diaphragm is necessary to set illumination according to the Koehler system.

This element is used in a diaphragm installed in various Carl Zeiss Jena microscope models built on the Amplival stand:
- Amplival
- Amplival Interphako
- Amplival Pol
- Vertival
- Peraval
- Fluoval
- Docuval

The field diaphragm located in the microscope base is part of the transmitted light path - it is not a diaphragm for EPI (reflected) illumination. However, it is VERY LIKELY that individual blades may also fit reflected light diaphragms and other diaphragms (e.g. aperture diaphragms) in Carl Zeiss Jena microscopes and condensers.

Damage to iris diaphragm blades is one of the more common failures in Carl Zeiss Jena microscopes. Most often this occurs when:
- the lubricant in the diaphragm opening / closing mechanism dries out and the user tries to move it by force
- a foreign object gets between the blades (e.g. a glass fragment from a chipped microscope slide)
- the diaphragm is closed too quickly or opened too far

In the event of an iris diaphragm failure, it is possible to:
- replace the entire element (condenser or diaphragm module)
- replace only the diaphragm
- repair the diaphragm by replacing the damaged blades

Description of this part for the microscope.

microscopes from other manufacturers, especially when Carl Zeiss Jena Planachromat objectives are mounted.

Description of this part for the microscope.

illumination collector
- potentiometer for light intensity control
- illuminator with halogen lamp
- transformer integrated into the base (Zeiss P/N 392575-9001)
- power cable with EU plug

Description of this part for the microscope.

illumination according to the Koehler standard
- slot for inserting the illuminator
- angled mirror reflecting the light beam

Important - some versions have a base with a removable illumination collector module with a field diaphragm. This base has this module permanently mounted (screwed), but there is no difference in operation between these versions.

Important - the base does not include the illuminator. The Standard GFL model uses illumination with a 6V 15W bulb mounted in a holder (Lampenfassung). This illuminator is connected to an external transformer. It is a separate component and is not included with the base.

Description of this part for the microscope.

eu/foto/owner-1/_manuals/Carl-Zeiss-Jena-MHP-160.pdf

Description of this part for the microscope.

element is intended for the Carl Zeiss Jena Fluoval microscope. THIS IS NOT CERTAIN INFORMATION - I am unable to access the relevant documentation.

Other used names:
- lamp holder
- lamp tube
- lamp support
- sometimes the German-language term "Lampenhaus" is used

Description of this part for the microscope.

Photomicroscope II (Phomi) microscope, but I understand it also fits the other Zeiss microscopes.

Description of this part for the microscope.

Description of this part for the microscope.

except for the circuitry that operates the LCD.

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

installed. It enables ergonomic work with the microscope by tilting the observation head at an angle.

Note - this is not a tube with a photo port (that is, it is not a so-called "trino"). It is a tube intended for mounting a binocular head and it does not have a third optical light path.

Other names used for this microscope part:
- Angle tube
- Angular tube
- Inclined tube
- Intermediate tube
- Angle intermediate tube
- Inclined intermediate tube

Description of this part for the microscope.

illuminator housing with frosted filter
- illuminator tube
- illuminator holder with frosted filter
- sometimes the German-language term "Lampenhaus" is used

Notice - this is NOT a complete illuminator assembly. Please carefully examine the photos in the gallery; as an additional element (which is not included here), a separate silver component extending beyond the outline of the microscope base is screwed in to help support the illuminator with bulb. Here I offer and describe the part that is located inside the microscope base.

Description of this part for the microscope.

a glass frosted filter (so-called ground glass) is located in the optical light beam path. It is mounted on a steel rod ending with a handle positioned outside the microscope base - at the rear, next to the place where the illuminator is inserted. This handle is used to insert and withdraw the frosted filter from the illumination beam path.

This design often leads to damage:
- the glass frosted filter is mounted on the rod in such a way that the glass frequently cracks
- the handle located at the rear of the microscope base very often breaks or crumbles
- the metal rod often jams and as a result of attempts to move it - bends

Here I present and offer this exact frosted filter with the complete movement mechanism:
- glass frosted filter (ground glass)
- holder for mounting the filter to the rod
- all necessary screws to attach this set to the microscope base
- plastic control knob for operating the ground glass

Description of this part for the microscope.

integrated gear for adjusting the height of the microscope condenser, as well as a rack with the element on which the condenser holder is mounted.

Description of this part for the microscope.

Zeiss.

Description of this part for the microscope.

the gear rack on which this mechanism moves is NOT included in the kit.

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

an incandescent lamp illuminator. This lampholder is not required if you have a microscope with the original halogen illuminator - in that case, the collimator lens is a separate element mounted next to the field diaphragm.

Other used names:
- lamp holder
- lamp tube
- lamp support
- sometimes the German-language term "Lampenhaus" is used

Description of this part for the microscope.

documentation, this element is referred to in German as -Fototubus 100/100 und Tubusträger-.

This is a photographic tube on which a binocular microscope head is mounted - in this configuration it becomes a complete trinocular system. At the top there is an optical output where a camera or photographic device can be mounted.

Basic technical parameters:
- light beam splitting: 0/100 and 100/0
- head mounting method: dovetail 41.5 mm
- mounting method on the photographic port: dovetail 41.5 mm
- internal lens: additional Bertrand lens e.g. for phase contrast adjustment
- extras: slot for installing a filter wheel

Note - despite certain similarities, this microscope element DOES NOT FIT Carl Zeiss Jena Jenamed microscopes.

Description of this part for the microscope.

a CZJ Ergaval / Amplival microscope with a classic illuminator (6V 15W filament bulb) and simply replacing the bulb holder with the one offered here will create a halogen-illuminated microscope. No.
- the original holder of the "regular" bulb contains a lens that collimates the light beam
- the halogen bulb holder does not contain that lens
- Ergaval / Amplival microscopes designed for halogen illumination have an additional lens threaded into the base

Halogen illumination is (according to many experts) the best microscope illumination because it delivers strong light with a full spectrum, whereas LED often provides only a portion of the color spectrum.

Other used names:
- illuminator
- halogen lamp
- bulb holder
- lamp housing

Description of this part for the microscope.

This is a component of the transmitted light optical path - it is not a diaphragm for EPI reflected light.

This part fits various Carl Zeiss Jena microscope models built on the Amplival stand:
- Amplival
- Amplival Interphako
- Amplival Pol
- Vertival
- Peraval
- Fluoval
- Docuval

Description of this part for the microscope.

Zeiss Jena factory.

Description of this part for the microscope.

(471710)

This turret mounts with a dovetail joint, allowing you to quickly swap out entire sets of objectives without having to unscrew them individually if you have more than one turret.
This allows you to have a complete set of low-power objectives on one turret and a complete set of high-power objectives on the other, quickly swapping them as needed.

Description of this part for the microscope.

ergonomic wrist rests. Four screws are included to secure it to the microscope.

NOTE - This base DOES NOT FIT the Carl Zeiss Jena Amplival microscope.

Description of this part for the microscope.

collimating lens and a mirror that reflects light vertically upward.

When attached to the Amplival model, this accessory can convert it into a microscope with EPI illumination.

The last photo shows an excerpt from the user manual describing this accessory.

Description of this part for the microscope.

Description of this part for the microscope.

The Carl Zeiss Jena Technival stereomicroscope has two such knobs ? one on each side of the body. They are identical, and there's no difference between left and right.

The aluminum cap must be removed to attach the knob. After that, it must be glued back on.

Description of this part for the microscope.

Description of this part for the microscope.

Dovetail/mounting connector for the microscope body
- Dovetail connector diameter: 43 mm
- Lower bottom lens

Here is the same part, but without the screws.

Sorry, I don't know the part number. It's a binocular head mounted on Carl Zeiss Standard 14 and Standard 16 microscopes.

Description of this part for the microscope.

P/N number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads?but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads - but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

Standard 14 microscope

I apologize, but I don't know the P/N number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads - but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

Description of this part for the microscope.

30W for halogen lighting. This is a complete element integrated with part of the housing. Screws are included. The set includes an ON/OFF switch for mounting in the housing. The set DOES NOT include a light intensity regulator.

Description of this part for the microscope.

numerical aperture.

Description of this part for the microscope.

Description of this part for the microscope.

screws to attach to the arm. The slider has two places - one has a removable filter and the other is empty.

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

lenght: not sure (finite)
Focal lenght: not sure (vintage)
Immersion: yes, Oil

Description of this part for the microscope.

length: not sure (finite)
Focal length: not sure (vintage)
Immersion: no (dry, air)

Description of this part for the microscope.

sure (finite)
Focal length: not sure (vintage)
Immersion: no (dry, air)