Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

33 mm
Cover Glass: 0.17 mm
Immersion: Yes, oil immersion
Thread: RMS
Info: Ph = phase contrast. NOTE - this is not a "Phv" type contrast.

This objective lens is in excellent condition, with no signs of use. It's difficult to find an objective lens of this quality on the used parts market.

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

Description of this part for the microscope.

mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS
Info: Ph = phase contrast. NOTE - this is not a "Phv" type contrast.

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

Description of this part for the microscope.

The set in the wooden box is visible in the last photo, but this is only an example.

Description of this part for the microscope.

The set in the wooden box is visible in the last photo, but this is only an example.

Description of this part for the microscope.

The set in the wooden box is visible in the last photo, but this is only an example.

Description of this part for the microscope.

The set in the wooden box is visible in the last photo, but this is only an example.

Description of this part for the microscope.

The set in the wooden box is visible in the last photo, but this is only an example.
[key, tool, Schlüsselwerkzeug, Schlüssel, Werkzeug, klucz, kluczyk]

Description of this part for the microscope.

The set in the wooden box is visible in the last photo, but this is only an example.
[key, tool, Schlüsselwerkzeug, Schlüssel, Werkzeug, klucz, kluczyk]

Description of this part for the microscope.

The set in the wooden box is visible in the last photo, but this is only an example.
[key, tool, Schlüsselwerkzeug, Schlüssel, Werkzeug, klucz, kluczyk]

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

polarized transmitted light with the possibility of use as a brightfield condenser
Mounting: the condenser is permanently integrated with a dovetail mount
Top lens: flip-out system allowing the upper lens to be moved into or out of the optical path to change the numerical aperture
Iris diaphragm: yes
Diffuser: yes, with the possibility of moving it into or out of the optical path
Polarizer: yes, rotatable, with the possibility of moving it into or out of the optical path

This condenser fits the following Carl Zeiss Jena microscope models:
- Polmi-A
- Nf
- Ng
- Nu / Nu2

Note: despite the visual similarity of the mounting interface, this condenser does NOT fit the Carl Zeiss Jena Lu microscope.

Important: the condenser is permanently integrated with the dovetail mount and cannot be used with other microscopes without significant modifications.

Description of this part for the microscope.

Length: 33 mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

Description of this part for the microscope.

10 160/-
Color correction: Planachromat
Numerical aperture: 0.10
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Color correction: Planachromat
Numerical aperture: 0.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.32
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 1,25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: HI = Homogene Immersion, also oil immersion

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

for taking microscope photographs or recording microscope videos. This is a gray photographic adapter.

Basic technical parameters:
- mounting connection to microscope stand: 41 mm dovetail
- output connection type on the photo port: 49 mm internal thread
- connection for binocular head mounting: Jena standard 41 mm dovetail
- magnification directed to the binocular head: 1.6x
- magnification on the photo output: none (that is 1.0x)

Because this photo head has a 49 mm threaded output, virtually any device, camera, adapter, tube or other accessory can be connected after using an appropriate 49 mm thread adapter. Direct projection technique may be used (because there is no additional optics inside), or any projection eyepieces may be installed in the optical path.

This photographic attachment is intended mainly (but not exclusively) for the following microscope models:
- Carl Zeiss Jena Eduval
- Carl Zeiss Jena Laboval
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Telaval
- Carl Zeiss Jena Pictoval
- Carl Zeiss Jena Epignost

The list above contains Mikroval series microscopes with gray housings - just like the tube shown and offered here. However, it also works with older black Carl Zeiss Jena microscopes:
- Carl Zeiss Jena L-Stativ (models Lg, Lu and Lr)
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Ng
- Carl Zeiss Jena Nf (and NfPk)

Please note that microscopes from other manufacturers also use the 41 / 41.5 mm dovetail connection standard. Because of this, this photographic head can also be used with microscopes made by:
- Lomo (for example Lomo Biolam)
- Meopta
- IOR
- selected Reichert microscopes (for example Reichert Neozet)
- Will Wetzlar
- Hund Wetzlar
- Leitz Wetzlar

This Carl Zeiss Jena tube is also very often used with microscopes having a larger head mounting diameter. In such cases users apply additional spacer or thickening rings. Because of this, this photo adapter also fits microscopes from manufacturers such as:
- PZO (for example the PZO Biolar model with 43 mm connection)
- Olympus (for example the Olympus CH model with 42 mm connection)

The element that allows a photographic camera or imaging camera to be connected to Carl Zeiss Jena Mikroval series microscopes may be referred to by different names. Commonly used names include:
- trino head
- trinocular head
- photo head
- photographic head
- photo attachment
- photographic attachment
- photo adapter
- photographic adapter
- photo tube
- photographic tube
- phototube
- photographic angle tube
- and various combinations of the words head, attachment, adapter or tube with terms such as photo, photographic, for camera and similar

Description of this part for the microscope.

mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

The fact that this objective has FL = 33 mm allows it to be used with microscopes from other manufacturers, including:
- Lomo Biolam
- Lomo MBB-1A
- PZO MB-10
- Olympus CH

Description of this part for the microscope.

unscrewed. It is mounted onto the dovetail guide located underneath the microscope stage carrier and secured with a clamping screw.

Carl Zeiss Jena Ergaval microscopes were originally equipped with a condenser attached to the "MO" holder. This holder has a permanently mounted iris diaphragm and wide-field lens, while the condenser itself is screwed into the upper thread. In this configuration, the condenser cannot be exchanged.
The Carl Zeiss Jena Fluoval uses a similar arrangement, whereas the Carl Zeiss Jena Amplival was originally equipped with a panchromatic condenser.

If the user wishes to use other condensers (including those made by manufacturers other than Carl Zeiss Jena), the original condenser holder must be replaced with the MZ condenser holder. Once this has been done, any microscope condenser with a mounting diameter of 39.5 mm can be installed. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

This is exactly such a holder for interchangeable condensers.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: grey, the version manufactured for the Mikroval microscope series
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this component is grey, it is also compatible with older black Carl Zeiss Jena microscopes from the 1950s and 1960s (it simply will not look completely original unless it is repainted).

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of condenser holder, making it easy to identify the component.

Description of this part for the microscope.

unscrewed. It is mounted onto a dovetail guide located underneath the microscope stage carrier. The condenser holder is secured to the guide with a clamping screw.

It can accommodate any microscope condenser with a mounting diameter of 39.5 mm, regardless of the manufacturer. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: black, the version manufactured for the black Carl Zeiss Jena microscopes from the 1950s and 1960s
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this microscope component is black, it is also compatible with the newer grey Carl Zeiss Jena microscopes of the Mikroval series.

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of the condenser holder, making it easy to identify the component.

Description of this part for the microscope.

diameter: 23.2 mm

This eyepiece allows the microscope image to be projected onto a surface such as a wall, ceiling or projection screen.

Originally, this eyepiece model was supplied with the Carl Zeiss Jena Pictoval projection microscope. It can also be installed on virtually any microscope from any manufacturer with a 23.2 mm eyepiece tube.

Important: Projecting a microscope image requires a very large amount of light, so a high-power illuminator is necessary.

Description of this part for the microscope.

head in Carl Zeiss Jena Pictoval projection microscopes (microprojectors). The adjustable tilt angle of the eyepiece tube, which held a projection eyepiece (usually f=100), allowed the position of the projected image on the projection surface to be changed.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Eyepiece mounting diameter: 23.2 mm
Mounting to the microscope arm: 41 mm diameter dovetail ring

Because this microscope head has a Carl Zeiss Jena standard microscope mount (a 41 mm diameter dovetail ring), it can be mounted on most microscopes from this manufacturer (e.g. Carl Zeiss Jena Eduval, Laboval, Ergaval, Amplival, etc.), as well as on microscopes made by Lomo (e.g. Lomo Biolam), IOR and Meopta.

It seems useful to mention a few points:
- never look through this microscope head with the naked eye if a projection eyepiece is installed in it and the head is mounted in a Carl Zeiss Jena Pictoval microprojector. This may result in loss of eyesight due to the very high light output emitted by this microscope
- when mounting this microscope head on a microscope other than a Carl Zeiss Jena Pictoval, a different magnification scale may be obtained than with the original heads designed for the particular microscope model
- projecting a microscope image requires a great deal of light, i.e. a powerful illuminator. This is worth remembering if you intend to use this head to project an image from biological microscopes with standard incandescent illumination (e.g. 15 W 6 V), which is definitely not sufficient
- visual observation using this microscope head may be inconvenient because it has a different (smaller) tilt angle than standard monocular or binocular microscope heads

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Serial number: 039 562 (039562)
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

camera to a trinocular head or directly to the microscope stand, even when there is no trinocular head at all.

This is a black tube with an upper element (barrel) 55 mm long. Here (https://www.microscopeparts.eu/gallery/91057) you can see a functionally identical adapter, but grey and with an upper barrel only 25 mm long.

Black adapters of this kind come from the era of the Carl Zeiss Jena L stands (models Carl Zeiss Jena Lg, Lumipan, Ng, Nf or Nu). The grey ones are newer, from the era of the Mikroval series (models Carl Zeiss Jena Laboval, Eduval, Ergaval or Amplival and Docuval).

The mounting fit is of course identical, so both can be used interchangeably.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: black
Inclination angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to a trinocular head or microscope stand: ring dovetail
Ring dovetail diameter: 41.5 mm
Type of connection at the output: empty barrel / tube
Tube diameter at the output: 23.2 mm inner diameter
Barrel / tube length: 55 mm
Tube length adjustment: no - this is not a height-adjustable tube

Because on the output side this adapter has an empty barrel with an inner diameter of 23.2 mm, you can place in it a projection eyepiece of that diameter or a so-called USB eyepiece, that is a digital microscope camera. In addition, adapters between the 23.2 mm barrel and the M42 thread are widely available, and from the M42 thread you can already move on to any other mount: Nikon, Canon, Sony and all the rest.

Such a tube can be mounted directly on the microscope stand, in place of the head. A seat for a ring dovetail of 41.0 - 41.5 mm diameter is found among others in the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH
- Gamma

It is also used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can likewise be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the microscopes Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in LOMO Polam microscopes
- some versions of the black intermediate photo tubes for the microscopes Carl Zeiss Jena Lg / Lumipan / Nf and of the grey ones from the Mikroval series (others require a tube that screws in on a thread)

This is not a tube for one particular microscope model. A trinocular head can be mounted not only on the microscope it was sold with, so the correct assumption is that this is a universal tube with a ring dovetail of 41.5 mm diameter on one side and a barrel of 23.2 mm diameter on the other.

In the compatibility section you will find an example list of microscopes this tube fits, although that list is not complete.