Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

5 mm or others if you put a thickening ring on it.
The upper lens for strong magnifications can be unscrewed and then we get a condenser for objectives with low magnification and low numerical aperture.
I can't (or it is not possible) unscrew the lower part with the diaphragm separately.

Description of this part for the microscope.

mm
Focal length: 37 mm
Immersion: no (dry, air)

Description of this part for the microscope.

mm
Focal length: 37 mm
Immersion: no (dry, air)

Description of this part for the microscope.

N.A. 0.65 Met
Magnification: 40x
Color correction: achromat
Numerical aperture: 0.65
Tube length: 170 mm
Focal length: 37 mm
Thread: RMS
Coverglass: no
Immersion: no
Info: metallographic objective

Possible applications:
- working with reflected light (EPI)
- working with transmitted light without a coverglass

Application areas:
- metallography (surface structure)
- mineralogy (minerals, micrometeorites)
- quick viewing of smears (e.g., blood)
- extreme macro photography

Description of this part for the microscope.

N.A. 0.30 Met
Magnification: 10x
Color correction: achromat
Numerical aperture: 0.30
Tube length: 170 mm
Focal length: 37 mm
Thread: RMS
Coverglass: no
Immersion: no
Info: metallographic objective

Possible applications:
- working with reflected light (EPI)
- working with transmitted light without a coverglass

Application areas:
- metallography (surface structure)
- mineralogy (minerals, micrometeorites)
- quick viewing of smears (e.g., blood)
- extreme macro photography

Description of this part for the microscope.

N.A. 0.65 PO.
Magnification: 40x
Color correction: achromat
Numerical aperture: 0.65
Tube length: 170 mm
Focal length: 37 mm
Thread: RMS
Coverglass: yes, 0,17 mm
Immersion: no
Info: polarisation objective

Of course, the "PO" designation doesn't mean it's designed "solely" for polarizing. It can be used in any microscope for both polarization and brightfield transmitted light.

Description of this part for the microscope.

(?)
Focal length: 37 mm

The optics (lenses) in this microscope objective are in very good condition.

There's no manufacturer's marking on the objective lens. Because lenses from different manufacturers looked very similar at the time, I'm not sure whether Hertel & Reuss manufactured the lenses themselves or ordered them from another company (e.g., Leitz). Therefore, these lenses can be safely used with microscopes from many other manufacturers.

Description of this part for the microscope.

(?)
Focal length: 37 mm

The optics (lenses) in this microscope objective are in very good condition.

There's no manufacturer's marking on the objective lens. Because lenses from different manufacturers looked very similar at the time, I'm not sure whether Hertel & Reuss manufactured the lenses themselves or ordered them from another company (e.g., Leitz). Therefore, these lenses can be safely used with microscopes from many other manufacturers.

Description of this part for the microscope.

(?)
Focal length: 37 mm

The optics (lenses) in this microscope objective are in very good condition.

There's no manufacturer's marking on the objective lens. Because lenses from different manufacturers looked very similar at the time, I'm not sure whether Hertel & Reuss manufactured the lenses themselves or ordered them from another company (e.g., Leitz). Therefore, these lenses can be safely used with microscopes from many other manufacturers.

Description of this part for the microscope.

RMS
Tubus length: 170 mm (?)
Focal length: 37 mm
Immersion: yes, oil

The optics (lenses) in this microscope objective are in very good condition.

There's no manufacturer's marking on the objective lens. Because lenses from different manufacturers looked very similar at the time, I'm not sure whether Hertel & Reuss manufactured the lenses themselves or ordered them from another company (e.g., Leitz). Therefore, these lenses can be safely used with microscopes from many other manufacturers.

Description of this part for the microscope.

it fits the CN series or the STE-6 stereo microscope (I'll post here once I find out).

Modell: HAPRO

Update: I just tested it with a Hertel & Reuss CN-hf / CN-fl microscope. The illuminator fits perfectly, but the CN-hf / CN-fl doesn't have a mirror underneath (Umlenkspiegel), so you'll need to install one yourself and it will work perfectly (see last photos).

Description of this part for the microscope.

polarization kit
Intended for: monocular biological microscopes
Type: for working with transmitted light

This allows you to view objects in polarized transmitted light, which produces very beautiful effects, for example, when observing descaling agent, vitamin C, or sand.

The kit includes:
- a polarizer that attaches to the light source
- an analyzer that attaches to the eyepiece

NOTE: Make sure the eyepiece diameter is suitable for mounting the analyzer.

Description of this part for the microscope.

B=bino, FO = foto)
Eyepiece diameter: 23.2 mm
Mounting diameter: 50 mm
Photo thread: 24 mm (M24)

A trinocular head is a binocular microscope head with an additional third optical port for connecting a camera or photographic device.

This particular unit comes from a Hertel & Reuss Studio II microscope, but it also works with any other microscope model from this manufacturer that has an interchangeable head with a mounting diameter of 50 mm.
NOTE - as far as I remember, not all H&R microscopes have an easily interchangeable head; this applies, for example, to the Primus model.

NOTE - some microscope models from Steindorff Berlin also have a head mounting diameter of 50 mm and are fully compatible with H&R heads - an example of such a microscope with a Hertel & Reuss head can be seen on Facebook at the following address: https://www.facebook.com/groups/136833493390496/posts/1722336908173472/

Other names:
- photographic head
- photo head
- trinocular head
- trino

Description of this part for the microscope.

10
Magnification: 5x
Numerical Aperture: 0.10
Thread: RMS
Tubus length: 170 mm
Focal length: 37 mm

Among Hertel & Reuss low-magnification objectives, those with 4:1 magnification are most commonly found on the market. This 5:1 magnification model, especially in the newer housing version offered here, is rare.

This objective can be used with practically any microscope that
- has an RMS objective thread
- TL = 170 mm
- FL = 37 mm

Description of this part for the microscope.

simple microscope stages with clips for holding the specimen. Therefore, at magnifications above 400x, manually manipulating the slide with the specimen becomes very difficult. XY cross stages are used for this purpose, for example, to move the specimen very precisely at 500x, 600x od 1000x magnification with oil immersion.

This is not a cheap plastic cross stage - it is a well-made Hertel & Reuss design.

NOTE - if the mounting pin spacing matches, this cross stage can be mounted on stages from virtually any manufacturer.

Note - this is version "A" of the XY cross-stage mechanism - it differs from version "B" only in the shape of the screws, but in order to ensure that my photos always show the original item, each variant is listed separately in the database.

Note - Hertel & Reuss manufactured cross stages with fixed specimen clamps as well as a model with a spring-loaded clamp. Here I present and offer the version with fixed clamps.

Description of this part for the microscope.

simple microscope stages with clips for holding the specimen. Therefore, at magnifications above 400x, manually manipulating the slide with the specimen becomes very difficult. XY cross stages are used for this purpose, for example, to move the specimen very precisely at 500x, 600x od 1000x magnification with oil immersion.

This is not a cheap plastic cross stage - it is a well-made Hertel & Reuss design.

NOTE - if the mounting pin spacing matches, this cross stage can be mounted on stages from virtually any manufacturer.

Note - this is version "B" of the XY cross-stage mechanism - it differs from version "A" only in the shape of the screws, but in order to ensure that my photos always show the original item, each variant is listed separately in the database.

Note - Hertel & Reuss manufactured cross stages with fixed specimen clamps as well as a model with a spring-loaded clamp. Here I present and offer the version with fixed clamps.

Description of this part for the microscope.

simple microscope stages with clips for holding the specimen. Therefore, at magnifications above 400x, manually manipulating the slide with the specimen becomes very difficult. XY cross stages are used for this purpose, for example, to move the specimen very precisely at 500x, 600x od 1000x magnification with oil immersion.

This is not a cheap plastic cross stage - it is a well-made Hertel & Reuss design.

NOTE - if the mounting pin spacing matches, this cross stage can be mounted on stages from virtually any manufacturer.

Note - Hertel & Reuss manufactured cross stages with fixed specimen clamps as well as a model with a spring-loaded clamp. Here I present and offer the version with spring.

Description of this part for the microscope.

not intended for so-called "thick" objectives
Thread in the cap: no, the cap of this objective case does not contain a thread for attaching an RMS objective

This objective case can be used to store so-called "short" objectives (DIN 33 mm), longer objectives (DIN 37 mm), and long objectives (DIN 45 mm), provided they are not the so-called "thick" type.

Various names are used on the secondary market for a microscope objective case, including:
- objective case
- microscope objective case
- objective container
- microscope objective container
- objective storage case
- objective storage container
- objective box
- objective storage box
- protective objective case
- objective lens case
- objective lens container
- dust protection case
- transport case for microscope objectives
- microscope objective holder case
- storage canister for microscope objectives

Each case has the Hertel & Reuss logo on its cap.

Although this case is of greatest interest to users and collectors of objectives made by the manufacturer Hertel & Reuss, it can of course be used to store objectives from any manufacturer.