Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

Poland
- Model: 5/0.15 160/-
- Alternative model marking: 5/0.15 160/0
- Magnification: 5x
- Numerical aperture N.A.: 0.15
- Correction: achromatic
- Focal length FL: 33 mm
- Tube length: 160 mm
- Cover glass: not required, but may be used
- Immersion: no (dry objective)
- Thread: RMS

This model has a metal housing with no lens at its end. Additionally, this housing can be unscrewed without affecting the operation of the objective - resulting in a relatively large working distance of more than 20 mm.

Three features:
- large working distance exceeding 20 mm
- exceptionally high numerical aperture N.A. of 0.15
- achromatic correction allowing direct projection use
make this relatively uncommon model very frequently chosen for macro photography using a microscope objective connected to a camera (focus stacking).

The fact that this objective has FL = 33 mm allows it to be used with microscopes from other manufacturers, including:
- Lomo Biolam
- Lomo MBB-1A
- Carl Zeiss Jena LG / Lu / Lumipan
- Carl Zeiss Jena Nf
- Olympus CH

Note! Please note that the FL = 33 mm focal length means that this objective DOES NOT FIT the following microscopes:
- PZO Biolar
- PZO Studar

Early versions of this objective (with low serial numbers) have the engraved marking 5/0.15 160/0 suggesting that the objective is intended for use without a cover glass. This is true, but more precisely this objective can work both without a cover glass and with one. In newer versions the engraving already reads 5/0.15 160/- where this "minus" already means "indifferent".

Description of this part for the microscope.

diffuser)
- blue
- yellow
- green

New (usually Chinese) microscope filters are sometimes not even made of glass. And even if they are made of glass - you may encounter scandalous examples where the glass is only surface-colored. Unfortunately, cheap colored glass filters may not be internally homogeneous and can cause light refraction distortions.

This filter set by PZO was originally sold together with the PZO Biolar microscope. It was manufactured in the 1970s (and certainly before 1977), so these are optical glasses that are about half a century old! They have never been used until now (this is so-called NOS - New Old Stock), therefore these are excellent old-class optical glasses of the highest quality.

Filters with a 32 mm diameter are used - and can be used - in microscopes from various manufacturers:
- Carl Zeiss Jena
- Zeiss West Germany
- Eschenbach
- Meopta
- Nikon
- ROW
- Leitz Wetzlar
- Wild
- Hund
- Kosmos
- and many others

Important - popular microscopes by Lomo (for example Lomo Biolam) have a 33 mm filter holder, so the filters shown here have too small a diameter and may fall out from some Lomo holders.

Description of this part for the microscope.

, DIC or polarizing
- iris diaphragms

Often compatible with microscopes from other manufacturers.

Description of this part for the microscope.

Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: no
Thread: RMS
Info: Phv = phase contrast variable

It can be used with any microscope from any manufacturer, along with a compatible Phv phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

The fact that this objective has FL = 33 mm allows it to be used with microscopes from other manufacturers, including:
- Lomo Biolam
- Lomo MBB-1A
- PZO MB-10
- Olympus CH

Description of this part for the microscope.

Length: 33 mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

The fact that this objective has FL = 33 mm allows it to be used with microscopes from other manufacturers, including:
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lumipan
- Lomo Biolam
- Lomo MBB-1A
- PZO MB-10
- Nikon S
- Olympus KHC

Description of this part for the microscope.

Jena
Name: Grossfeld Binocular
Eyepiece mounting diameter: 30 mm
Microscope mount: 41 mm dovetail mount
Diopter adjustment: yes, for one eyepiece

The set also includes two eyepieces:
- Model: Carl Zeiss Jena GF-Pw 10x (25)
- Mounting diameter: 30 mm

This head is most commonly used in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, widefield binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older Mikroval series microscopes (for example Ergaval and Amplival). If the microscope is additionally equipped with GF-Planachromat series widefield objectives (or GF-Planapochromat objectives used in Docuval microscopes) - this creates the best possible combination for Carl Zeiss Jena microscopes with a 160 mm tube length.

This microscope head model is identical to the Baader Mark V binocular viewer used in astronomical telescopes and is often purchased by astronomy enthusiasts and adapted for telescope mounting.

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
Carl Zeiss Jena Jenamed 2 and Jenamed Histology microscopes already use different stages.

This particular example shown and offered here was removed from a Carl Zeiss Jena Jenamed Cytology microscope.

The stage in Carl Zeiss Jena Jenamed microscopes is a flat, smooth surface permanently attached with screws to the microscope body, onto which cross table mechanisms or specimen holders are mounted - various versions depending on individual needs.

Mechanically, this stage consists of two elements:
- a smooth upper steel surface attached to the cast form underneath
- the lower cast form (with manufacturer number), which is attached to the microscope body
Both parts have an opening for the microscope condenser. The condenser is mounted from the underside of the stage (condenser available separately).

Metal cast or injection-moulded microscope parts made by Carl Zeiss Jena have their own numbers. This part carries the number 2712 (full marking: Si10 CZ 2712).

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

microscope. It will most likely also fit other models from the Jenamed series (e.g. Jenamed Variant, Jenamed Fluorescence, Jenamed-2, Jenamed Hematology). Please note however that the Carl Zeiss Jena Jenamed Histology microscope is factory-equipped with a different type of condenser - the "flip-out" type.

To make sure whether this condenser will fit a specific Carl Zeiss Jena microscope from the Jenamed series, it is best to carefully check all dimensions based on the gallery photos or ask a question on a professional forum, e.g. https://www.mikroskopie-forum.de/

Mechanically, this condenser is mounted from the underside of the microscope stage - first it is screwed into the threaded opening in the stage and then secured with three screws. The upper lens can be unscrewed to obtain a condenser with a lower numerical aperture N.A. This condenser does not have an iris diaphragm installed because in Jenamed microscopes it is a separate element.

Replacing the condenser in a Carl Zeiss Jena Jenamed microscope may be necessary:
- when the upper lens becomes damaged, for example when it turns matte due to exposure to various chemical reagents
- when the upper lens becomes damaged due to rubbing. Surprisingly, this unusual type of damage is very common after several decades of microscope use.

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

was removed from a Carl Zeiss Jena Jenamed Cytology microscope. It will most likely also fit other models from the Jenamed series (e.g. Jenamed Variant, Jenamed Fluorescence, Jenamed-2, Jenamed Hematology).

It does not fit the Jenamed Histology model because the Carl Zeiss Jena Jenamed Histology microscope features a different type of condenser (a 'flip-out' type) by default. For this reason, the iris diaphragm is located slightly lower than in other models and is different.

To make sure whether this iris diaphragm will fit a specific Carl Zeiss Jena microscope from the Jenamed series, it is best to carefully check all dimensions based on the gallery photos or ask a question on a professional forum, e.g. https://www.mikroskopie-forum.de/

Mechanically, this diaphragm is mounted underneath the condenser. The entire diaphragm module is attached to the microscope body with four screws. It is not mechanically connected to the condenser - these are separate elements. The lever pin used to open / close the diaphragm protrudes through a special opening at the front of the microscope, making it possible to adjust the diaphragm opening. This opening is located in the cover of the filter wheel - here one can see further relationships between the individual elements of the light path.

Carl Zeiss Jena Jenamed microscopes do not have a field diaphragm.

Replacement of the aperture diaphragm module in a Carl Zeiss Jena Jenamed microscope may be necessary:
- when some of the iris diaphragm blades become damaged (bent or broken)
- when the lever used to open / close the diaphragm breaks off
- when the teeth of the gear wheel mounted in this module become damaged

Metal cast or injection-moulded microscope parts made by Carl Zeiss Jena have their own numbers. This part carries the number 2713 (full marking: Si10 CZ 2713).

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

Basic parameters:
- Number of objective positions: 5
- Thread: M25
- Mounting method: integrated with a larger block attached to the microscope body using screws

Yes - the "click-stop" detent mechanism (German: Blattfeder) is included, as it is frequently damaged in this model.

Metal cast or injection-moulded parts made by Carl Zeiss Jena have their own numbers. This part carries the number: 2708 (full marking: Si10 CZ 2708).

Please note - the small block with slots for microscope sliders, attached to this revolver and bearing the number Si10 CZ 2709/2, is available separately.

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

Variant, Cytology, Hematology, Histology, Jenamed-2, Fluorescence)
- Jenapol
- Jenavert
- Jenaval
- Jenatech
- Jenalumar

Please note - this is only the adjustment knob, that is the knob used by the microscope user to make the illumination brighter or dimmer. It is not a potentiometer and therefore not a part of the electrical circuit.

This knob features the characteristic white cap used on Carl Zeiss Jena microscopes, which is often lost during decades of microscope use.

Mechanically, this knob is attached to the potentiometer. The fixing screw is covered by a white metal cap.

In the last photo I indicate with an arrow exactly which element it is and where it is located in a Carl Zeiss Jena Jenamed microscope. In Jenaval and Jenalumar microscopes it is located on the microscope base.

Description of this part for the microscope.

Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

The function of this element is to reflect light coming from the microscope base vertically upwards so that, after passing through the microscope slide with the specimen and the objective, it reaches the eyepieces and ultimately the user's eyes.

Metal cast or injection-moulded parts made by Carl Zeiss Jena have their own numbers. This part carries the number: 2721 (full marking: Si10 CZ 2721).

Replacement of the angle mirror in Carl Zeiss Jena Jenamed microscopes may be necessary in the following cases, among others:
- if the mirror becomes significantly scratched as a result of improper cleaning (minor scratches are usually not visible during normal use)
- if the reflective silver coating of the installed mirror becomes oxidised
- if the mirror becomes damaged, chipped or cracked, for example after coming loose from its mount

Description of this part for the microscope.

attached to the microscope stand with screws. It serves as a mounting platform for mechanical stages, XY stage mechanisms, or specimen holders - various versions depending on the user's requirements.

Mechanically, this stage consists of two elements:
- a smooth upper steel plate attached to the cast component below
- a lower cast component (with the manufacturer's part number) attached to the microscope stand
Both parts have an opening for the microscope condenser. The condenser is mounted from below the stage (condenser available separately).

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This part is marked with number 2712 (full marking: Si10 CZ 2712).

This microscope stage DOES NOT FIT the following Carl Zeiss Jena microscopes:
- Jenamed 2
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Fluorescence

More precisely: the lower part (marked Si10 CZ 2712) is identical to the one used in other Jenamed microscope models (except Jenamed-2), whereas the smooth upper steel plate used in the Jenamed Histology differs from those used in other models by the size of the condenser cut-out (opening).

In the last photo, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

This diaphragm DOES NOT FIT the following Carl Zeiss Jena microscopes:
- Jenamed 2
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Fluorescence

Mechanically, this diaphragm is mounted below the condenser. The complete diaphragm module is attached to the microscope stand with two screws. It is not mechanically connected to the condenser - these are separate components. The lever (pin) used to open and close the diaphragm extends through a dedicated opening at the front of the microscope, allowing adjustment of the diaphragm opening. This opening is located in the cover of the filter wheel - illustrating further relationships between successive elements of the light path.

Carl Zeiss Jena Jenamed microscopes do not have a field diaphragm.

Replacement of the aperture diaphragm module in a Carl Zeiss Jena Jenamed Histology microscope may be necessary:
- when one or more iris diaphragm blades become damaged (bent or broken)
- when the lever used to open and close the diaphragm breaks off
- when the teeth of the gear wheel installed in this module become damaged

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This part bears number 2714 (full marking: Si10 CZ 2714). The iris diaphragm module used in the other Carl Zeiss Jena Jenamed microscope models bears part number Si10 CZ 2713.

Description of this part for the microscope.

therefore cannot be used in:
- Jenamed Cytology
- Jenamed Variant
- Jenamed Hematology
- Jenamed Fluorescence
- Jenamed-2

Mechanically, this condenser is a "flip-out" design and is mounted in a metal frame together with a lever used to rotate it in order to obtain one of two operating modes: low or high numerical aperture N.A. This lever extends outside the microscope housing so that the user can operate it.

The complete module is mounted underneath the microscope stage by attaching the entire condenser assembly from below with four screws. This condenser does not contain an iris diaphragm because, in Jenamed microscopes, it is a separate component mounted beneath the condenser.

In the Carl Zeiss Jena Jenamed Histology microscope, this condenser is not used together with the wide-field lens that is installed beneath the condenser in other Jenamed models (part Si10 CZ 2711-1). In the Jenamed Histology model, a polarizer is installed in this position instead.

Replacement of the condenser in a Carl Zeiss Jena Jenamed Histology microscope may be necessary:
- when the upper lens becomes damaged, for example by becoming cloudy due to exposure to various chemical reagents
- when the upper lens is damaged by friction. Surprisingly, this unusual type of damage is very common after several decades of microscope use
- when the mechanical lens switching mechanism ("flip-out") becomes damaged

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This condenser module bears number 2713 (full marking: Si10 CZ 2713).

In the last photograph, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

2 Fluorescence

It DOES NOT FIT Carl Zeiss Jena microscopes from the Jenamed series and therefore cannot be used in:
- Jenamed Cytology
- Jenamed Variant
- Jenamed Hematology
- Jenamed Histology

Mechanically, this condenser is mounted on the microscope stage support plate (stage support). The microscope stage is installed onto this support plate together with the condenser. The upper condenser lens can be unscrewed - after removing it, the condenser operates with a lower numerical aperture N.A.

This condenser does not contain an iris diaphragm because, in Jenamed microscopes, it is a separate component mounted beneath the condenser.

Replacement of the condenser in a Carl Zeiss Jena Jenamed-2 microscope may be necessary:
- when the upper lens becomes damaged, for example by becoming cloudy due to exposure to various chemical reagents (common in fluorescence applications)
- when the upper lens is damaged by friction. Surprisingly, this unusual type of damage is very common after several decades of microscope use

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. The microscope stage support plate on which the condenser is mounted bears number 3030 (full marking: Si10 CZ 3030).

In the last photograph, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

Lichteinstellupe (Centering / Focus telescope)
Mounting diameter: 23.2 mm + original 30 mm adapter

This centering telescope can be used for:
- DIC alignment (Differential Interference Contrast)
- Phase contrast alignment (centering phase rings)
- Aperture diaphragm inspection (iris diaphragm observation)Filament centering when setting up Köhler illumination

This is one of those microscope elements for which many different names are used. Among others:
- phase telescope
- phase contrast telescope
- phase alignment telescope
- phase adjustment telescope
- phase centering telescope
- phase contrast centering telescope
- phase contrast alignment telescope
- phase contrast adjustment telescope
- centering telescope
- condenser centering telescope
- condenser alignment telescope
- condenser adjustment telescope
- alignment telescope
- adjustment telescope
- inspection telescope
- aperture viewing telescope
- back focal plane viewing telescope
- auxiliary microscope
- phase contrast auxiliary microscope
- alignment auxiliary microscope
- centering auxiliary microscope
- adjustment auxiliary microscope
- auxiliary telescope
- centering scope
- alignment scope
- phase scope
- phase viewer
- phase contrast viewer
- phase centering eyepiece
- phase contrast eyepiece
- phase alignment eyepiece
- phase telescope eyepiece
- centering eyepiece
- condenser centering eyepiece
- adjustment eyepiece
- inspection eyepiece

Description of this part for the microscope.

and the nosepiece is mounted from underneath.

Based on the Carl Zeiss Jena Amplival microscope, whose modular design allows for various configurations, several microscope models were created:
- Vertival
- Epival
- Amplival Interphako
- Amplival Pol
- Fluoval
and these microscopes differ from each other, among other things, by different arms. The arm from the Amplival model has the simplest construction.

By owning different arms and one microscope - you can swap them according to your needs and use different functionalities, as if you had two microscope models.

This element consists of the following components:
- fixing screw securing the arm to the microscope body
- holder enabling the mounting of components with a 41 mm mounting diameter (e.g. binocular head)
- fixing screw securing this component (e.g. head). This element is very often damaged.
- guides (slides) enabling the attachment of an interchangeable nosepiece

A device with a matching mounting diameter that is placed on the arm from above can be, for example:
- head with a built-in inclined tube
- intermediate tube (German: Zwischentubus)
- magnification changer (Optovar)
- EPI reflected light illuminator
- polarization analyzer module
- and others, because as mentioned above, the Amplival class microscopes have a modular design and there are many accessories available for them

This microscope arm can solve the following issues related to Carl Zeiss Jena Amplival class microscopes:
- if your microscope is missing this element, which happens with microscopes available on the secondary market
- if you own another variant of a microscope from this class, e.g. Carl Zeiss Jena Vertival, and you want to convert it into a "regular" Amplival
- if you own such an arm, but it is of poor quality or has damaged individual components
- if you need one of the component parts of this arm
- if you are building your own DIY project and need a mount compatible with the Carl Zeiss Jena standard

On the last photo, an arrow indicates which element it is and where it is located in the microscope to clearly identify this part.

Important: The popular and visually very similar Carl Zeiss Jena Ergaval microscope, which is often confused with the Amplival model, DOES NOT HAVE such a modular design and this arm does not fit it.

If you need any of the component parts of this arm (e.g. the large fixing screw securing the arm to the microscope stand or the smaller fixing screw securing the head to the arm - search this database or contact us by writing an email.

Description of this part for the microscope.

Amplival microscope
Number of lenses: 3
Numerical aperture N.A.: variable, from N.A. 0.16 to N.A. 1.4
Aperture diaphragm: yes, screwed on as a detachable module

The Carl Zeiss Jena pancratic condenser has three upper lenses:
- for working with low magnification objectives (usually up to 6.3x)
- Apl. 1.4 for working with high magnification objectives
- an oil immersion cardioid darkfield lens with N.A. = 1.05

Mechanically, this condenser is mounted on dovetail rails located on the microscope stage holder block.

Here are the mounting possibilities of the pancratic condenser to Carl Zeiss Jena microscopes:
- to Amplival, Docuval, Epival, Fluoval, Vertival microscopes, this condenser can be mounted directly
- to Ergaval, Nu, Nu 2, Nf microscopes, this condenser is mounted after unscrewing the aperture diaphragm from it
- to Jenaval, Jenapol, Jenalumar microscopes, this condenser can also be mounted, but it is installed together with the entire stage holder block from the Amplival microscope http://www.microscopy-uk.org.uk/mag/artfeb09/rs-jenalumar.html
- be careful, because the Lumipan microscope also features a pancratic condenser, but with a completely different mounting method

This condenser is often used as a "parts donor" for own DIY projects, for example:
- the Apl. 1.4 lens is often used to modify (upgrade) condensers with a lower numerical aperture N.A. in various microscopes
- the darkfield lens is very often used to build a standalone cardioid condenser
- the iris diaphragm has a very wide range of applications

On the last photo, an arrow indicates which element it is and where it is located in the microscope to clearly identify this part. Additionally, the attached video shows how the individual elements of this condenser move.

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

This is a microscope element placed in the microscope base. It transmits the light beam from the illuminator, unifies it (blurs the filament image using a diffuser), and then properly focuses it using a collimating lens. The light beam prepared in this way then hits an angular mirror (this is a separate element).

This microscope part is known on the secondary market among DIY enthusiasts creating their own optics projects and is frequently used by them.

Description of this part for the microscope.

magnification is very often used as a projection eyepiece for microphotography.

This eyepiece works with any microscope from any manufacturer that allows the use of eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed-2
- Jenamed Fluorescence

Important: this element is not used in the Jenamed Histology model. In this microscope version, a flip-out type condenser is used, and instead of the wide-field lens there is a polarizer. In other words - this element does not fit the Carl Zeiss Jena Jenamed Histology microscope.

This lens enables uniform illumination of the specimen when working with low magnification objectives. It is most commonly used with 3.2x and 5x objectives. It is an element installed in the microscope base and is part of the transmitted light illumination system.

Mechanically, this lens has a pin that extends outside the housing so that the user can insert or remove the lens from the optical path. It is mounted below the condenser aperture diaphragm. In Jenamed microscopes, the condenser, the aperture diaphragm, and this wide-field lens are all separate modules.

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This condenser module bears number 2711-1 (full marking: Si10 CZ 2711-1).

Description of this part for the microscope.

following Carl Zeiss Jena microscopes:
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology

This is a large module that is mechanically integrated, although it can be disassembled into smaller parts. However, if replacement becomes necessary, it is usually more convenient to replace the complete assembly. For this reason it is presented and offered here as a complete unit.

The assembly shown here includes:
- internal power supply electronics (potentiometer, transformer, etc.)
- fine focus mechanism (micro-adjustment)

If you need any individual component from this assembly, for example the transformer, a specific electronic board, only the brightness control potentiometer, or only the fine focus mechanism itself, please contact us by email.

Please note:
- the power supply is compatible with every Carl Zeiss Jena Jenamed microscope model, including Jenamed 2 and Jenamed Fluorescence
- however, the complete fine focus mechanism assembly does NOT fit Jenamed-2 and Jenamed Fluorescence, although some smaller components of the fine focus mechanism are identical across all Jenamed microscope models

This complete assembly may be required to solve, among others, the following problems in Carl Zeiss Jena Jenamed microscopes:
- when the microscope illumination does not work due to a defective power supply. This may be caused by mains voltage surges, ageing electronic components, or damage resulting from improper modifications (for example LED conversions)
- when the illumination works but brightness adjustment does not function because of a defective or worn potentiometer
- when the fine focus mechanism does not work properly, for example when the objective turret does not move upward or slowly drops by itself

It is very important to note that the internal power supply used in Carl Zeiss Jena Jenamed microscopes converts 220-240V mains voltage to 6V with a maximum power output of 25W. This power supply has the same specifications as those used in Carl Zeiss Jena Jenaval and Carl Zeiss Jena Jenalumar microscopes. If you own one of these microscopes with a defective power supply, any qualified electronics technician can transfer the electronics from a Jenamed microscope.

Description of this part for the microscope.

even though they are similar models. Carl Zeiss Jena Technival and Technival-2 microscopes use stepwise magnification switching (built-in magnification turret), while Carl Zeiss Jena Citoval and Citoval-2 microscopes feature continuously variable magnification (so-called zoom) - therefore the objectives are not interchangeable between these models.

This particular achromatic objective shown and offered here was removed from a Carl Zeiss Jena Citoval-2 microscope. Unfortunately, I am not certain whether it also fits the Carl Zeiss Jena Citoval microscope (without the "2").

For this microscope element in the Carl Zeiss Jena Citoval-2 microscope, the manufacturer uses several different names:
- Main objective (German: Hauptobjektiv)
- Objective (German: Objektiv)
- Front objective (German: Frontobjektiv)

This is the main objective of the microscope, to which an auxiliary objective (German: Vorsatzobjektiv, Vorsatzlinse, Vorsatzsystem) may optionally be attached, although this is not required.

The Carl Zeiss Jena Technival and Citoval microscopes (older version without the number "2") are grey, while the Technival-2 and Citoval-2 models are white. This objective is white and is therefore intended for the newer Carl Zeiss Jena Citoval-2 and Technival-2 stereo microscopes.

Description of this part for the microscope.

2490)
- metal plate for the base, black on one side and white on the other
- vertical steel post (stand)
- rack gear of the vertical movement mechanism
- focusing block with adjustment knobs (manufacturer's catalog name: Mikroskoptrieb 65 mm)
- holder to which the microscope body is mounted directly.
In the operating manual (https://www.mikroskop-online.de/Mikroskop%20BDA/30-725-1%20%20TECHNIVAL%202%20%20CITOVAL%202.pdf), these elements are numbered 1, 2, 3 and 35 on page 4.

Please note that the original rack gear used in Carl Zeiss Jena Citoval-2 microscopes is made of plastic and this component is very frequently damaged. If this particular element in your microscope has failed, Askania Mikroskop Technik Rathenow fortunately offers professionally manufactured brass rack gears for this microscope model (https://askania.de/products/zahnstange-messing-l-96mm).

Metal, cast or injection-moulded Carl Zeiss Jena parts carry their own identification numbers. This base (foot), into which the vertical stand post is screwed, bears the number 2490 (full designation: Si10 2490).

The Carl Zeiss Jena Technival and Citoval microscopes (older version without the number "2") are grey, while the Technival-2 and Citoval-2 models are white. This stand is white and is therefore intended for the newer Carl Zeiss Jena Citoval-2 and Technival-2 stereo microscopes.

Description of this part for the microscope.

illuminator)
Light source: 6V 25W halogen bulb, standard Narva HLWS5-A

This is a complete illuminator consisting of the following components:
- lamp housing with lenses for collimating the light beam
- light source with halogen bulb
- mounting holder for the Citoval-2 / Technival-2 microscope
In the user manual (https://www.mikroskop-online.de/Mikroskop%20BDA/30-725-1%20%20TECHNIVAL%202%20%20CITOVAL%202.pdf) these components are marked as items 7 and 8 on page 4.

Mechanically, this illuminator is mounted on an arm (illuminator holder), which can be clearly seen in the video attached to this description. This holder is attached to a special clamp located on the main objective.
The main objective of the Carl Zeiss Jena Citoval-2 / Technival-2 microscopes has two such clamps, allowing two holders and therefore two illuminators to be mounted. This allows the observed object to be illuminated from both sides. This is exactly why many users look for an additional illuminator.

This illuminator requires a transformer. It uses a 6V low-voltage halogen bulb and therefore cannot be connected directly to a mains power outlet.

The Carl Zeiss Jena Technival and Citoval microscopes (older version without the number "2") are grey, while the Technival-2 and Citoval-2 models are white. This illuminator is white and is therefore intended for the newer Carl Zeiss Jena Citoval-2 and Technival-2 stereo microscopes.

Description of this part for the microscope.

microscope objective
- Manufacturer: Carl Zeiss Jena
- Designation: Planachromat 25x/0,50 oo/0,17
- Magnification: 25x
- Numerical aperture N.A.: 0,50
- Optical correction: infinity-corrected tube length
- Optical correction class: planachromat
- Cover glass: yes, 0.17 mm
- Thread: M19

Some facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes from this manufacturer:
- these objectives are most commonly used for technical applications rather than biological applications, therefore most objectives available on the secondary market are intended for use without a cover glass (designation oo/0)
- CZJ M19 objectives intended for biological applications (designation oo/0,17) are most commonly used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with an EPI illuminator
- CZJ M19 objectives can be used in Carl Zeiss Jena Polmi-A microscopes, but they provide a different magnification than the nominal value
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes feature interchangeable nosepieces, and a dedicated nosepiece for M19-thread objectives was also produced for these microscopes
- Carl Zeiss Jena Metaval and Neophot microscopes use newer versions of CZJ M19 objectives (with a coarse-knurled edge and shiny housing), although many users still experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various versions with completely different configurations - and some of them operate with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow the use of CZJ M19 objectives in EPI dark-field mode
- on the Carl Zeiss Jena Epityp-2 inverted metallurgical microscope, many users employ biological objectives designed for use with a cover glass, placing the microscope slide "upside down", with the cover glass facing downward toward the objective.

Description of this part for the microscope.

for microscope slides. It allows quick insertion and replacement of slides without the use of an XY mechanical stage.

Several different specimen holding systems are found in Carl Zeiss Jena microscopes. The slide cassette system is one of them and represents an alternative to traditional designs using a mechanical stage and slide-retaining clips.

Various names are commonly used for this specimen holder, including:
- slide cassette (German: Gleitkassette)
- specimen cassette (Ger.: Objektkassette)
- microscope specimen cassette
- specimen holder
- slide holder

This is not a complete stage-mounted system and therefore it is not a "slide cassette system". It is only the cassette itself (slide cassette), which is a replaceable wear item installed into the appropriate carrier assembly.

In the last gallery photograph, I indicate the exact component being offered with an arrow.

Description of this part for the microscope.

objective nosepiece. It consists of slots (empty openings) into which filter sliders are inserted. This is the component that the Microscopy-UK portal (https://www.microscopy-uk.org.uk/mag/imgmar09/JenamedFinal.pdf) referred to as "in-tube filter holders".

This filter holder is compatible with the following Carl Zeiss Jena microscopes:
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

Metal, cast, and injection-moulded parts manufactured by Carl Zeiss Jena have their own identification numbers. This part bears the number: 2709/2 (full designation: Si10 CZ 2709/2).

Mechanically, this "block with empty slots" is attached to the casting numbered Si10 CZ 2708, which is the objective nosepiece block.

In the last photo of the gallery, I use an arrow to show exactly which component is being described.

Description of this part for the microscope.

in the microscope.

As far as I know, the same mechanism is used in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval
- Peraval

This component is installed onto the shaft by sliding the internal tab into the keyway groove on the shaft. After tightening the round slotted nut, a locking mechanism is created that prevents the nut from loosening on its own due to vibration.

Instructions for disassembling the fine- and coarse focus mechanism in a Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

movement in the microscope.

As far as I know, the same mechanism is used in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval
- Peraval

This component acts as a resistance regulator and functions as a friction brake. Tightening the outer element compresses the tapered section of the bushing, causing the slotted bushing to contract at the slit. This increases friction on the shaft and makes the entire mechanism move with greater resistance.

Note - in some descriptions available on the Internet, this component is referred to as a "piece of wood".

Instructions for disassembling the coarse focus and fine focus mechanism in a Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

any microscope from any manufacturer that allows the use of eyepieces with a mounting diameter of 23.2 mm.

The company "Dr. G. Schuchardt Göttingen" did not and does not produce microscopes. Previously, it primarily sold microscopes manufactured by Hertel & Reuss and Will Wetzlar under its own brand.

Description of this part for the microscope.

adjustment together with a rack gear and the component on which the condenser holder is mounted.

Note - this module DOES NOT FIT Carl Zeiss Jena Nf and Carl Zeiss Jena Lu microscopes, even though the assemblies performing the same function in those microscopes look VERY similar.

In the last photos in the gallery, I use arrows to show exactly which microscope component is being offered and where it is located in the Carl Zeiss Jena NU-2 microscope.

Description of this part for the microscope.

Stand family).

The Carl Zeiss Jena Lu microscope features a modular design (the same as the larger Carl Zeiss Jena Nf microscope). This microscope part (this module) consists of the following components:
- dovetail mounting with a clamping screw for attachment to the condenser lifting block
- condenser holder with a retaining screw for securing the condenser
- iris diaphragm (aperture diaphragm)
- iris diaphragm sliding carriage allowing lateral movement of the diaphragm
- eccentric mechanism allowing rotation of the carriage, making it possible to illuminate not only from the sides but also from the front or rear
- spring plate (lock) allowing the entire diaphragm assembly to be moved out of the optical path

The condenser holder has an internal mounting clamp for condensers with a diameter of 39.5 mm.

The movable iris diaphragm mounted below the microscope condenser allows oblique illumination and produces a three-dimensional image effect that increases the contrast of transparent specimens (for example individual unstained cells). This provides an effect similar to Differential Interference Contrast (DIC).

Various names are used on the secondary market for this microscope part, including:
- decenterable iris diaphragm
- decentering aperture diaphragm
- off-axis iris diaphragm
- eccentric iris diaphragm
- sliding iris diaphragm
- sliding iris
- oblique illumination condenser
- condenser with sliding iris
- oblique illumination module
- oblique illumination diaphragm
- offset iris
- Poor Man's DIC device

Note - this condenser module DOES NOT FIT Carl Zeiss Jena Nf, Ng, Lumipan, Polmi-A or Nu microscopes, even though the mounting arrangement appears very similar at first glance.

Description of this part for the microscope.

Jena
Version: grey version, removed from a Carl Zeiss Jena Amplival microscope
Mounting method: aperture diaphragm in the form of a detachable module
Centerable: yes

This iris diaphragm module is mechanically mounted to the bottom of the panchromatic condenser.

In Carl Zeiss Jena panchromatic condensers, the diaphragm is designed as a detachable module because it can be removed and replaced, for example, with a phase contrast module or a polarization module. Precisely because this microscope part can be detached, it is often missing from condensers available on the secondary market - over the years it simply gets lost.

Interestingly, this microscope part is very often modified. When users do not have a phase contrast module or a polarization module, they frequently insert polarizing film or custom-made phase rings into the aperture diaphragm module and obtain the functionality they need through DIY modifications.

This module can also solve a common problem found in Carl Zeiss Jena Amplival microscopes, namely damaged diaphragm blades in the condenser.

Description of this part for the microscope.

The engraved scale on the ring allows the currently selected magnification to be determined.

In the Carl Zeiss Jena Citoval-2 stereomicroscope, continuous magnification adjustment (known as zoom) is implemented inside the microscope body (Greenough system), while the objective lens has a fixed focal length.

The set also includes a threaded retaining ring that allows this assembly to be mounted to the microscope body.

Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope, in order to clearly identify this part.

Description of this part for the microscope.

attach the microscope to the stand. In the Carl Zeiss Jena Citoval-2 microscope user manual (https://www.mikroskop-online.de/Mikroskop%20BDA/30-725-1%20%20TECHNIVAL%202%20%20CITOVAL%202.pdf, page 4), the stand component to which this rail is fitted is identified as part number 35.

This rail is often chipped or broken because it is made of a relatively brittle material, while the screw used to clamp it to the stand is made of steel (this can be clearly seen in the following photo: https://www.microscopeparts.eu/photo/carl-zeiss-jena-citoval-2-technival-2-stereomikroskop-tischstativ-mit-fokussiertrieb-99477-7). An impact or even excessive tightening of this screw may cause this mounting rail to chip or break.

This microscope part can help solve the following problems encountered when using a Carl Zeiss Jena Citoval-2 or Technival-2 microscope:
- if you own a microscope that was previously used without its stand or on a custom boom arm and no longer has this mounting rail
- if this rail has been chipped or broken due to impact damage or material fatigue and the microscope can no longer be securely mounted to its table stand

Interestingly, this mounting rail is also an excellent component for adapting a microscope from another manufacturer to a table stand originally designed for Carl Zeiss Jena Citoval-2 / Technival-2 microscopes. It is sufficient to attach this mount to the microscope body (mounting screws are included).

In addition, the last photographs in the gallery include an arrow indicating exactly which part is being offered and where it is located within the microscope, allowing this component to be identified unambiguously.

Description of this part for the microscope.

35 160/0.17
Manufacturer part number: 46 05 10-9906 (alternative notation: 460510 - 9906)
Color correction: Planachromat
Numerical aperture N.A.: 0.35
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm thickness
Immersion: no (dry objective)
Thread: RMS

Description of this part for the microscope.

65 160/0.17
Manufacturer part number: 46 07 10-9904 (alternative notation: 460710 - 9904)
Color correction: Planachromat
Numerical aperture N.A.: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm thickness
Immersion: no (dry objective)
Thread: RMS

Description of this part for the microscope.

17
Magnification: 40x
Correction: Achromat
Numerical aperture: 0.65
Tube length: 160 mm
Focal length: 33 mm
Cover glass: yes, 0.17 mm thickness
Immersion: no (dry objective)
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it must support RMS objectives with TL=160 mm and FL=33 mm. After installing a 12 mm adapter, this objective can of course also be used in microscopes designed for FL=45 mm.

The fact that this objective has FL = 33 mm (meaning it is a so-called short objective) allows it to be used with microscopes from other manufacturers, including:
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lumipan
- Lomo Biolam
- Lomo MBB-1A
- PZO MB-10
- Nikon S
- Olympus KHC

Description of this part for the microscope.

(12,5)
Mounting diameter: 23.2 mm
Eyecups: yes, one pair

These eyepieces are most commonly used in the following microscopes:
- Carl Zeiss Jena Technival / Technival-2
- Carl Zeiss Jena Citoval / Citoval-2

The Carl Zeiss Jena Technival and Citoval microscopes (older type without the number "2") are grey in colour, while the Technival-2 and Citoval-2 models are white. These eyepieces are white, which means they are intended for the newer versions of the Carl Zeiss Jena Citoval-2 and Technival-2 stereo microscopes.

Description of this part for the microscope.

bright field
- dark field
- oblique illumination
- phase contrast

It can work with phase objectives of different magnifications and from different manufacturers (it is sufficient to manually adjust the ring diameter).

Basic parameters:
Manufacturer: Leitz Wetzlar
Model: Heine condenser
Mounting diameter: 39.5 mm
Numerical aperture N.A.: variable, up to 1.4

This Heine condenser was designed for microscopes with a condenser holder in the form of a circular clamp (e.g. Leitz SM microscopes). It is not a condenser that slides into mounting rails (as found, for example, in the Leitz Orthoplan microscope).

This condenser fits microscopes from many manufacturers (e.g. PZO, Steindorff Berlin, Zeiss, Carl Zeiss Jena, Leitz, Kremp Wetzlar, Will Wetzlar and many others) equipped with a 39.5 mm condenser holder.

Description of this part for the microscope.

although incorrectly, referred to as "Lomo")
Model: 20 0,40
Magnification: 20x
Correction: Achromat
Numerical aperture: 0.40
Tube length: 160 mm
Focal length: 33 mm
Cover glass: 0.17 mm
Immersion: no
Thread: RMS
Serial number: 01234

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm and FL=33 mm.

After installing a 12 mm adapter, this combination of adapter and objective will function as an objective with FL=45 mm.

This objective is attractive mainly to collectors because:
- there are very few microscope objectives with the LZOS logo on the secondary market
- the objective has a so-called "golden serial number": 01234

Description of this part for the microscope.

Carl Zeiss Jena, PZO, Meopta, Olympus, IOR and others.

This tube makes it possible to connect a camera or photographic camera to a trinocular head or directly to the microscope body, even when no trinocular head is installed.

Originally, this adapter was designed for the Lomo TRN-1 trinocular head. This head was used in Lomo Polam polarizing microscopes from the early 1970s onwards.

Several remarks regarding the model designation of the trinocular head for which this component was originally intended:
- the name Lomo TRN-1 is the Latin alphabet designation. In Cyrillic script the model designation appears as TPH (for example model TPH1Y4.2), and this designation is used in the manual for the Lomo Polam L-211 microscope
- the vast majority of these trinocular heads are not marked with any model designation
- the Envirotools website http://www.envirotools.hu/ateso_fenyu_polarizacios_mikroszkop.htm refers to this trinocular head as HU-POL

In the last photograph, an arrow indicates exactly which component is being offered and where it is located in the Lomo Polam microscope, allowing this part to be identified unambiguously.

Basic technical parameters of this tube:
Mounting method to the trinocular head or microscope: 41 mm dovetail mount (this is also the Carl Zeiss Jena standard)
Camera mounting method: male M39 thread
Alternative camera mounting method: since the M39 thread can be removed, a plain smooth tube with a diameter of 35 mm remains
Additional optics: yes, the original optics are installed inside, although they can be removed, leaving only an "empty tube".

This is not "a tube dedicated to a specific microscope model". It is a tube originally mounted on the third port (photo port) of a trinocular head. Since a trinocular head can be installed on microscopes other than the model with which it was originally supplied, this tube can be regarded as a universal accessory.

These technical parameters make it possible to use this tube with virtually any microscope manufactured by:
- Lomo (for example Biolam, Polam, MBB-1A and others)
- Carl Zeiss Jena (for example Ergaval, Amplival, Jenamed and others)
- IOR, Meopta and other manufacturers using a 41 / 41.5 mm dovetail mount

In addition, a 41 mm dovetail tube can easily be mounted on microscopes equipped with a 42 mm or 43 mm opening, for example:
- Olympus (for example CH, CH-2, BH-2 models)
- PZO (for example Biolar, Studar, MB-30 and others)

The entire list of microscope manufacturers and models given above may also be treated as a list of microscopes compatible with the Lomo TRN-1 trinocular head. Indeed, many examples can be found on the Internet showing this head being used with microscopes made by manufacturers other than Lomo.

Because this tube is equipped with an M39 thread by default, almost any camera or photographic camera can be attached by means of a suitable adapter, for example:
- devices with M42 threads
- devices with C-mount threads
- Nikon, Sony, Olympus and other camera standards

This is therefore a universal photo tube featuring a 41 mm dovetail on one side and either an M39 thread or a 35 mm tube on the other side.

In the image gallery, every photograph includes a millimetre scale, and in addition, the dimensions of the dovetail, tube and thread have been measured with calipers so that compatibility can be determined precisely.

Description of this part for the microscope.

Wetzlar
Model: 160/0,17 EF 100/1.25 OEL PHACO 3
Magnification: 100x
Correction: semi-plan achromat
Numerical aperture: 1.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm
Immersion: yes, oil
Thread: RMS
Specimen protection: yes - spring-loaded
Info: PHACO 3 = phase contrast

Some important information about this objective:
- the designation "EF" means "Extended Field" - this is a semi-plan achromatic objective with an 18 mm field of view, which should be taken into account when selecting suitable eyepieces
- the semi-plan achromatic correction is "almost flat" - it is no longer an achromat, but not yet a plan achromat
- this objective can be used in brightfield, but phase contrast operation requires a compatible phase contrast condenser or a slide (slider) with a phase ring diaphragm
- the designation PHACO 3 means that for phase contrast operation a phase contrast condenser set to ring "3" should be used (the equivalent setting used by Zeiss is called "Ph3")
- this objective can be used with microscopes designed for objectives with a 170 mm tube length, but in such a case the optical path must be extended by 10 mm - most commonly by pulling the eyepieces out of the tubes by 10 mm

This objective can be used with any microscope from any manufacturer together with a compatible phase contrast condenser. Naturally, the microscope must be compatible, i.e. it must support RMS objectives, TL=160 mm and FL=45 mm - or have adapters that make such adaptation possible (for example thread adapters).

Description of this part for the microscope.

(8)
Magnification: 20x
Field of view: 8
Mounting diameter: 23.2 mm
Designation: PK = plan compensating - recommended for use with plan achromatic objectives, but they also work perfectly with achromatic and apochromatic objectives

Due to their very high quality, these eyepieces are often used together with microscopes from other manufacturers, especially when Carl Zeiss Jena Planachromat objectives are installed.

Important: these eyepieces can be used both with finite tube microscopes (e.g. 160 mm) and infinity-corrected microscopes. This means that they can be used, for example, both on a Carl Zeiss Jena Amplival microscope and on a Carl Zeiss Jena NU-2 microscope.

Note - in my opinion, eyepieces with such a high magnification are recommended rather for "inspection" than for continuous work. I deliberately write "I recommend" because this is my personal opinion based on practical use and not on the manufacturer's documentation.
An eyepiece magnification of 20x should rather be treated as a zoom without revealing additional details (the resolution is not increased). This is important, for example, in heads with built-in magnification (e.g. Carl Zeiss Jena heads with built-in magnification of 1.5x or 1.6x) - when working with a 100x oil immersion objective, we theoretically obtain 100*1.5*20 = 3000x, while physics does not allow the human eye to magnify visible light beyond approximately 1250x - therefore this is a so-called "empty magnification".

Description of this part for the microscope.

allows two filters to be inserted into the EPI optical path, for example a frosted diffuser filter, a blue colour-balancing filter or a green filter used to facilitate metallurgical observations.

The photographs in the gallery show the exact dimensions of this slide.

Description of this part for the microscope.

the eyepieces are removed for transport or storage inside the wooden carrying case. Installing the caps prevents dust from entering the microscope head and reaching the internal prisms.

The offer applies to 2 (two) pieces, i.e. one pair. Each individual end cap features the original PZO logo.

These end caps fit stereo microscopes from any manufacturer, provided they use eyepieces with a mounting diameter of 34 mm:
- PZO MST-1 / MST-2
- PZO MST-130 / MST-131 / MST-132
- PZO MST ZOOM
- PZO KLP-21 / KLP-22 colposcopes
- DIY devices (e.g. queen bee insemination equipment) built using PZO MST stereo microscopes
- Meopta DM23
- Carl Zeiss Jena Stemi SM-16 / SM-20 (the so-called SM-xx series)
- medical optical instruments (e.g. ophthalmic slit lamps) manufactured by Carl Zeiss Jena and based on the SM-xx stereo microscope platform

These end caps do not fit microscopes using eyepieces with diameters other than 34 mm:
- they do not fit PZO MST-110 / MST-127 stereo microscopes because these use 23.2 mm eyepieces
- they do not fit Lomo MBC-1 / MBC-2 stereo microscopes because these use 30 mm eyepieces
- they do not fit Lomo MBC-9 / MBC-10 stereo microscopes because these use 32 mm eyepieces
- they do not fit Carl Zeiss Jena Technival / Citoval stereo microscopes because these use 23.2 mm eyepieces
- they do not fit Carl Zeiss West Germany stereo microscopes because these use 30 mm eyepieces
- they do not fit Euromex E-series and Z-series stereo microscopes because these use 30.5 mm eyepieces
- they do not fit Hertel & REUSS STE-series stereo microscopes because these use 31 mm eyepieces

The FAQ section of this database explains that these are genuine original parts rather than 3D-printed reproductions. It is worth repeating here: these are original vintage PZO plastic end caps. They are not generic "no-name" caps and they are not DIY parts made on a 3D printer.

The last photographs in the gallery show an example of these end caps installed on the head of a PZO MST-130 stereo microscope.

Description of this part for the microscope.

continuous zoom system.

The technical name of this microscope part is: rear fixed group (output group) of the pancratic zoom system. These are the two lenses permanently mounted inside the stereo microscope body, located directly below the binocular head.

This service part can help solve the following problems encountered when using the Carl Zeiss Jena Citoval-2 stereo microscope:
- if a lens has been mechanically damaged (scratched, cracked, or chipped)
- if a lens has become delaminated or its surface has been damaged by fungus (mold)
- if someone previously repaired the Citoval-2 microscope incorrectly and these lenses are either missing or in poor condition

In the last photographs, an arrow indicates exactly which microscope part is being offered and where it is located inside the microscope, making this component easy to identify. The final photograph shows a schematic diagram of the Greenough stereo microscope design.

Description of this part for the microscope.

continuous zoom system.

The technical name of this microscope part is: front fixed group (input group) of the pancratic zoom system. These are the two lenses permanently mounted inside the stereo microscope body, located above the main objective (Hauptobjektiv) of the stereo microscope.

This service part can help solve the following problems encountered when using the Carl Zeiss Jena Citoval-2 stereo microscope:
- if a lens has been mechanically damaged (scratched, cracked, or chipped)
- if a lens has become delaminated or its surface has been damaged by fungus (mold)
- if someone previously repaired the Citoval-2 microscope incorrectly and these lenses are either missing or in poor condition

In the last photographs, an arrow indicates exactly which microscope part is being offered and where it is located inside the microscope, making this component easy to identify. The final photograph shows a schematic diagram of the Greenough stereo microscope design.

Description of this part for the microscope.

Basic stand dimensions:
Support column diameter: 15 mm
Overall support column height: 220 mm
Glass plate opening diameter: 93.5 mm
Base length: 180 mm

The support column of this stand has a diameter of 15 mm. This allows virtually any stereo microscope or EPI metallurgical microscope with a 15 mm mounting bore to be installed on it, including:
- Carl Zeiss Jena Stemi SM-16
- Carl Zeiss Jena Stemi SM-20
- PZO MST-110 / MST-127
- PZO MST-130 / MST-131

When might this stand be needed?
- Stereo microscopes, including the Carl Zeiss Jena SM-xx series, were often used on special holders or boom stands. As a result, many of these microscopes available on the second-hand market no longer include their original bench stand.

Description of this part for the microscope.

parameters:
Filter colour: blue, matt
Function: NCB – converts the yellow light of the halogen lamp into naturally white light
Mounting diameter: adjustable from 25.5 mm to 26 mm

Mechanically, this filter is mounted on the front end of the halogen illuminator (over the light output opening). Its effect is to produce light with a colour similar to that emitted by a cool white LED.

Description of this part for the microscope.

ameters:
Manufacturer: Lomo
Model: PLAN 25x0.50 P
Original designation: ЛОМО ПЛАН 25х0,50 П
Magnification: 25x
Numerical aperture N.A.: 0.50
Tube length: 160 mm
Cover glass: yes, 0.17 mm thickness
Immersion oil: no – this is a dry objective
Focal length: 45 mm
Thread type: RMS
Additional designation: P (Cyrillic: П) indicates that this objective is designed for use with polarized light
Special features: built-in iris diaphragm
Year of manufacture: 1976

This objective has a standard RMS thread and TL=160 mm, which means it can be used with the vast majority of microscopes from virtually any manufacturer, including Olympus, Zeiss, Nikon, PZO, Carl Zeiss Jena, Reichert, Wild and many others.

The built-in iris diaphragm allows, among other things, precise centering of the objective, because in a polarizing microscope the following diaphragms may operate simultaneously:
- field diaphragm in the illuminator
- aperture diaphragm (or two aperture diaphragms) in the condenser
- iris diaphragm in the microscope objective
- iris diaphragm in the eyepiece head
and accurate centering of all of them relative to each other is very important in polarized-light observations.

Objectives marked "P" / "Pol" feature a special construction in which the lenses are mounted and cemented in a way that prevents mechanical stress. They can be used both for conventional brightfield microscopy and for observations in polarized light.

Description of this part for the microscope.

3
Numerical aperture N.A.: variable, from N.A. 0.16 to N.A. 1.4
Aperture diaphragm: no
Compatible microscope: Carl Zeiss Jena Lumipan

Mechanically, this condenser is mounted on a dovetail guide located beneath the microscope stage.

Several important notes:
- this pancratic condenser is compatible only with the Carl Zeiss Jena Lumipan microscope
- this condenser is not compatible with the Carl Zeiss Jena Nf or Carl Zeiss Jena Nu / Nu2 microscopes, even though the condenser used in those models is very similar
- this condenser does not include an iris diaphragm because the Carl Zeiss Jena Lumipan microscope has its aperture diaphragm located in the microscope base, directly below the condenser

In the last photograph, an arrow indicates which component is being described and where it is located in the microscope, making it easy to identify this part. In addition, the attached video shows how the individual components of this condenser move.

This condenser is often used as a "donor of parts" for DIY projects, for example:
- the Apl. 1.4 lens is often used to modify (upgrade) condensers with a lower numerical aperture N.A. in various microscopes
- the dark-field lens is very often used to build a custom cardioid condenser

Description of this part for the microscope.

Olympus CHK / CH / CH-2 microscope models were supplied with a square stage that does not include an integrated XY mechanical stage for precise specimen movement. Such a mechanism is a separate (optional) accessory mounted to the side of the stage, and this is exactly the accessory shown and offered here.

Basic information:
Item: XY mechanical stage attachment for microscope stage
Manufacturer: Olympus
Manufacturer's descriptive name: Fixed type mechanical stage with right downward coaxial knob for plane stage fixed
For microscope: Olympus CHK
Mounting method: attached to the side of the stage with two screws
Required stage thickness: from 10 mm to 12 mm

Important compatibility information:
Originally, this mechanical stage attachment was used on the Olympus CHK microscope. I have personally also installed it on Olympus CH and Olympus CH-2 microscopes, and it is fully compatible with both models.

If CH and CH-2 microscopes were originally supplied with an XY mechanical stage, they used the Olympus CH-MVR attachment, but this CHK version fits as well.

In addition, this XY mechanism is compatible with other microscopes provided that the stage thickness is between 10 mm and 12 mm. I have personally verified compatibility with the stages of the following microscopes:
- Carl Zeiss Jena Eduval
- Carl Zeiss Jena Laboval-2
- Motic SFC100

The last photographs in the gallery show the complete Olympus CHK microscope. An arrow indicates exactly which component is being offered and where it is located within the microscope. The final photograph also shows an Olympus CH-2 microscope fitted with this XY mechanical stage attachment.

In addition, the video available in the video gallery shows this stage from various angles and demonstrates the movement of all mechanical parts.

At magnifications above 400×, manually moving the microscope slide becomes very difficult. This is exactly why XY mechanical stage attachments are used, allowing the specimen to be moved with great precision at magnifications such as 600× or 1000× using oil immersion.

Description of this part for the microscope.

service replacement part intended for repairing a microscope stage in which this particular component has been damaged. It is not a complete microscope stage.

These rotating stages were used in L-Stativ class microscopes, including:
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lr

Please remember that microscopes and microscope parts manufactured by the Soviet company LOMO were often clones of Carl Zeiss Jena products. Therefore, this component may also fit a Lomo microscope stage, but the dimensions should always be compared very carefully before purchasing.

Carl Zeiss Jena manufactured these rotating stages from the 1930s until approximately the end of the 1960s. During that period many small design details were modified, so it is very important to correctly identify the stage model from which this component was removed.

- every photo in the gallery includes a millimetre scale
- the last photos show the microscope stage disassembled, with an arrow indicating exactly where this component is located
- the final photos also show the complete Carl Zeiss Jena Lg microscope fitted with this stage

All of this allows you to visually confirm that this is exactly the component you are looking for.

Description of this part for the microscope.

Stativ class microscopes.

This is a service replacement part intended for repairing a microscope stage in which this particular component has been damaged. It is not a complete microscope stage.

These rotating stages were used in L-Stativ class microscopes, including:
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lr

Please remember that microscopes and microscope parts manufactured by the Soviet company LOMO were often clones of Carl Zeiss Jena products. Therefore, this component may also fit a Lomo microscope stage, but the dimensions should always be compared very carefully before purchasing.

Carl Zeiss Jena manufactured these rotating stages from the 1930s until approximately the end of the 1960s. During that period many small design details were modified, so it is very important to correctly identify the stage model from which this component was removed.

- every photo in the gallery includes a millimetre scale
- the last photos show the microscope stage disassembled, with an arrow indicating exactly where this component is located
- the final photos also show the complete Carl Zeiss Jena Lg microscope fitted with this stage

All of this allows you to visually confirm that this is exactly the component you are looking for.

Description of this part for the microscope.

This scale is engraved into a specially shaped brass plate and then silver-plated. After several decades of use, this microscope part often becomes worn and the scale markings may become faint or completely invisible. When restoring such a microscope stage, replacing this scale may therefore be necessary.

This is a service replacement part intended for repairing a microscope stage in which this particular component has been damaged. It is not a complete microscope stage.

These rotating stages were used in L-Stativ class microscopes, including:
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lr

Please remember that microscopes and microscope parts manufactured by the Soviet company LOMO were often clones of Carl Zeiss Jena products. Therefore, this component may also fit a Lomo microscope stage, but the dimensions should always be compared very carefully before purchasing.

Carl Zeiss Jena manufactured these rotating stages from the 1930s until approximately the end of the 1960s. During that period many small design details were modified, so it is very important to correctly identify the stage model from which this component was removed.

- every photo in the gallery includes a millimetre scale
- the last photos show the microscope stage disassembled, with an arrow indicating exactly where this component is located
- the final photos also show the complete Carl Zeiss Jena Lg microscope fitted with this stage

All of this allows you to visually confirm that this is exactly the component you are looking for.

Description of this part for the microscope.

used in Carl Zeiss Jena L-Stativ class microscopes.

Additionally, this microscope part features a locking lever. Once the lever is engaged, the control knob can no longer be turned, locking the upper plate of the microscope stage in the desired position. The operation of this mechanism can be seen in the video available in the video gallery.

This is a service replacement part intended for repairing a microscope stage in which this particular component has been damaged. It is not a complete microscope stage.

These rotating stages were used in L-Stativ class microscopes, including:
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lr

Please remember that microscopes and microscope parts manufactured by the Soviet company LOMO were often clones of Carl Zeiss Jena products. Therefore, this component may also fit a Lomo microscope stage, but the dimensions should always be compared very carefully before purchasing.

Carl Zeiss Jena manufactured these rotating stages from the 1930s until approximately the end of the 1960s. During that period many small design details were modified, so it is very important to correctly identify the stage model from which this component was removed.

- every photo in the gallery includes a millimetre scale
- the last photos show the microscope stage disassembled, with an arrow indicating exactly where this component is located
- the final photos also show the complete Carl Zeiss Jena Lg microscope fitted with this stage

All of this allows you to visually confirm that this is exactly the component you are looking for.

Description of this part for the microscope.

the microscope stage:
1. It fastens the stage to the stage holder — that is, indirectly to the microscope stand. This ring has a groove for the spring screw mounted centrally in that holder, as well as two cut-outs at the sides — for the centring screws. It is not, however, a dovetail — in Carl Zeiss Jena L-Stativ microscopes the stage is mounted on a wide ring.
2. Since it is a sliding ring, it is precisely this part that makes it possible to rotate the stage all the way around, even though this is not a polarizing stage.

This is a service part for the repair of a stage in which exactly this element has been damaged. It is not a complete microscope stage.

This ring contains a screw that makes it possible to lock the position, that is, to press the ring tight so that it does not rotate. This screw very often bends completely (for example during transport) or even breaks off. Breakage most commonly occurs when the sliding grease has dried out completely and someone tries to turn the stage by pushing on this screw.

Rotating stages of this kind were used in microscopes of the L-Stativ class, among others:
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lr

Remember that microscopes and microscope parts made by the Soviet company LOMO were often clones of Carl Zeiss Jena products. It is therefore possible that this element will also fit a Lomo microscope stage — but the dimensions of this part should definitely be compared very carefully first.

Carl Zeiss Jena produced such stages from the 1930s until roughly the end of the 1960s. During that period minor construction details were changed many times, so it is very important to correctly identify the model of the stage from which this element was removed.

- in the photo gallery a millimetre scale is visible next to every photograph
- the last photographs show a disassembled microscope stage, with an arrow indicating where this element is located in the stage
- the final photographs, in turn, show the complete Carl Zeiss Jena Lg microscope with this stage fitted

All of this makes it possible to confirm visually that this is exactly the element you are looking for.

Description of this part for the microscope.

2

this module serves as the aperture diaphragm. The field diaphragm is built into the illumination path inside the microscope base.

At the same time, it provides a holder for 32 mm round filters. The video available in the gallery also demonstrates how a filter is inserted into this holder.

The sliding iris diaphragm mounted beneath the microscope condenser allows oblique illumination to be set, producing a three-dimensional image with enhanced contrast of transparent specimens (such as unstained cells). The resulting image is similar to differential interference contrast (DIC).

This component is known under various names, including:
- decenterable iris diaphragm
- decentering aperture diaphragm
- off-axis iris diaphragm
- eccentric iris diaphragm
- sliding iris diaphragm
- sliding iris
- oblique illumination condenser
- condenser with sliding iris
- oblique illumination module
- oblique illumination diaphragm
- offset iris
- Poor Man's DIC device

Note — this diaphragm DOES NOT FIT the Carl Zeiss Jena Lumipan microscope, even though it appears very similar at first glance.

Because this module is removable, it is missing from a large proportion of microscopes available on the second-hand market. During decades of use, these diaphragm modules were frequently lost.

In addition, they are often damaged and need replacement. The most common failures include:
- the protective glass covering the diaphragm becomes scratched or broken
- the diaphragm blades become bent or broken
- the screw used to decenter the diaphragm bends or breaks
- the return spring responsible for restoring the diaphragm to its centred position becomes damaged or is missing

Replacing the damaged assembly with the diaphragm module offered here solves these problems.

Description of this part for the microscope.

knobs
- coarse focus mechanism with the rack and control knobs
- microscope base with the rear illuminator port and a decenterable field diaphragm (iris diaphragm)
- stand arm with the microscope head mount and a dovetail guide for the interchangeable objective nosepiece
- dovetail guide with a rack and drive knob, together with the mounting module for a pankratic condenser or a clamp for mounting another condenser.

When can a complete microscope stand be useful?
- if you are building a microscope yourself and selecting every component so that the final configuration is exactly what you need
- if you own an older model (e.g. Carl Zeiss Jena Lg) - replacing the stand acts as an upgrade, while the remaining components are compatible between these models (except for the condenser)
- if your microscope is damaged or in poor condition - in this case the stand simply replaces the damaged microscope component
- if you need to replace only a single component in your damaged microscope (for example the fine focus block or the iris diaphragm), but decide to replace the entire stand instead

Contact us if you are looking for any part to repair a Carl Zeiss Jena Lumipan microscope. Even if the required part is not currently visible in the photographs or has not yet been added to this database as a separate product, it is located inside this complete microscope and is available. Examples include:
- knobs and control knobs
- racks and gears
- guides and shafts
- housing parts
- the iris diaphragm or its individual components
- illumination system components, deflecting mirror
- many other parts, from the complete upper tube down to the smallest screw or spring

The parts listed above are only examples - other components from this microscope stand may also be available.

Description of this part for the microscope.

body (that is, to the revolving magnification changer). It is secured with just a few small drops of adhesive.

This nameplate serves two purposes:
- it is positioned directly in front of the user's eyes, allowing the current total magnification to be identified immediately
- it protects the inside of the revolving magnification changer against dust and dirt entering the mechanism

Important: this nameplate does NOT fit the following microscopes:
- Carl Zeiss Jena Technival-2, because the magnification changer in this model has more magnification settings
- Carl Zeiss Jena Citoval / Citoval-2, because these models use a continuously variable ZOOM magnification system

Several decades have passed since the Technival series microscopes were manufactured, and these nameplates often simply fall off by themselves. They are also removed during servicing or repair of this microscope model, which is another common reason why they become lost.

Users solve the problem in various ways:
- they cover the "empty window" with almost anything
- they print a copy of the magnification table from a photograph of the original, glue it onto a piece of cardboard, and use this DIY replacement
- or they produce a replacement using a 3D printer, sometimes even with recessed lettering

However, if someone wants to have the original part, the only option is to find an original nameplate like the one offered here.

Description of this part for the microscope.

Carl Zeiss Jena microscope heads with a wide field of view (German: Grossfeld) have one eyepiece tube with diopter adjustment and a second one without it. Here I present the tube without diopter adjustment (straight eyepiece tube).

Basic parameters:
- Type: straight eyepiece tube
- Compatible eyepiece diameter: 30 mm
- Colour: white

Compatible with 30 mm microscope heads used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

Description of this part for the microscope.

hand when adjusting the interpupillary distance. It is a rounded metal cover that protects the eyepiece prism located underneath.

The last photo in the gallery shows a complete microscope head. An arrow indicates exactly which component is being described and where it is located inside the head, making it easy to identify.

Carl Zeiss Jena wide field microscope heads (those designed for 30 mm eyepieces) have two such components (two prism covers). They protect the prisms of the right and left eyepieces. Both covers are identical and interchangeable, so there is no constructional difference between the right-hand and left-hand cover.

This is a component for a microscope head, not for a specific microscope model.

This component fits microscope heads designed for 30 mm eyepieces used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Metal cast or injection-moulded components manufactured by Carl Zeiss Jena have their own part numbers. This component is marked with the number 2630 (full designation: Si10 2630 / Si10 CZ 2630). In addition, the number "1" or "2" appears next to the part number to indicate whether it is the cover for the right-hand or left-hand prism. This is the only difference, because mechanically the right-hand and left-hand covers are identical.

Description of this part for the microscope.

the front, in the centre of the binocular head, between the two eyepiece tubes. It is a round cover plate (end cap) carrying a scale from 55 to 75 indicating the interpupillary distance (eyepiece tube spacing).

The last photograph in the gallery shows the complete binocular head. An arrow indicates the exact component being offered and its location within the head, allowing it to be identified unambiguously.

This is a component of the binocular head rather than a component dedicated to a particular microscope model.

This component fits 30 mm eyepiece binocular heads used, among others, on the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Description of this part for the microscope.

microscope head to the microscope.

Basic specifications:
Mount type: dovetail
Diameter: 41 mm, the Carl Zeiss Jena and Lomo standard
Internal thread: 34 mm

The last photograph in the gallery shows a complete binocular head. An arrow indicates exactly which component is being offered and where it is located on the head, making visual identification straightforward.

This is a component of the microscope head rather than of any specific microscope model.

This component fits 30 mm binocular heads used, among others, on the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

This 41 mm Carl Zeiss Jena dovetail mounting standard is commonly used:
- if you want to perform a DIY conversion and mount a microscope head from another manufacturer onto a Carl Zeiss Jena or Lomo microscope
- if you want to connect another dovetail-mounted accessory to a Carl Zeiss Jena or Lomo microscope, such as an Optovar magnification changer, a polarisation intermediate tube, a DIC head or an EPI reflected-light illuminator
- if you want to use the 34 mm internal thread to mount a photographic tube for a camera