Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

20x / 0.45 oo/0.17-A
Color correction: Achromat
Numerical aperture: 0.45
Tube length: infinity
Focal length: not sure
Cover glass: 0.17 mm
Immersion: no
Thread: M25

This lens is often used with Leica microscopes (e.g., the DMLB, DMLS, or DM1000 models). It is often shorter than Leica objectives, but an extension adapter is used in these cases.

Description of this part for the microscope.

Achromat HI 100x / 1,25 oo/0.17-A
Color correction: Achromat
Numerical aperture: 1,25
Tube length: infinity
Focal length: not sure
Cover glass: 0.17 mm
Immersion: yes, oil
Thread: M25

This lens is often used with Leica microscopes (e.g., the DMLB, DMLS, or DM1000 models). It is often shorter than Leica objectives, but an extension adapter is used in these cases.

Description of this part for the microscope.

lenses:
- N.A. 0.3 for low-power objectives (this is the lens offered here)
- N.A. up to 1.4 (variable aperture) for high resolution and magnification
- oil dark field lens (cardioid condenser)

This condenser is used in Carl Zeiss Jena microscopes:
- Nf
- Nu / Nu2
- Lumipan
- Amplival (gray condenser)

but can also be mounted in the following microscopes:
- Jenaval
- Jenalumar
- Lu (I'm not sure)
- Ng
- Ergaval
- Docuval
- Polmi A

The companies IOR Bucuresti and Lomo made their own versions of pancratic condensers - I don't know if this lens is compatible with them.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

allows correction of vision in one eye and proper adjustment of image focus.

Basic parameters:
- Type: tube with diopter correction ring
- Diameter of supported eyepieces: 30 mm
- Color: white

Fits 30 mm heads used, among others, in the following Carl Zeiss Jena microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

Description of this part for the microscope.

06 oo/-A
Magnification: 3.2x
Numerical aperture N.A.: 0.006
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: not required, may be present or not
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

25 oo/-A
Magnification: 12,5x
Numerical aperture N.A.: 0.25
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: not required, may be present or not
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

17-A
Magnification: 25x
Numerical aperture N.A.: 0.50
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: yes, 0,17 mm
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

17-A
Magnification: 40x
Numerical aperture N.A.: 0.65
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: yes, 0,17 mm
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

commonly used in microscopes with a 30 mm eyepiece mounting diameter:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older microscopes of the Mikroval series (e.g. Ergaval and Amplival) - in such cases this eyepiece will also fit them, because - in general - eyepieces fit the head mounted on the microscope, not the microscope itself.

A single Carl Zeiss Jena PW 6.3x (25) eyepiece can solve the following problems:
- a second 6.3x eyepiece is missing to complete a pair
- a low magnification eyepiece is needed for use in a trinocular photo tube

Description of this part for the microscope.

Jena
Name: Grossfeld Binocular
Eyepiece mounting diameter: 30 mm
Microscope mount: 41 mm dovetail mount
Diopter adjustment: yes, for one eyepiece

The set also includes two eyepieces:
- Model: Carl Zeiss Jena GF-Pw 10x (25)
- Mounting diameter: 30 mm

This head is most commonly used in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, widefield binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older Mikroval series microscopes (for example Ergaval and Amplival). If the microscope is additionally equipped with GF-Planachromat series widefield objectives (or GF-Planapochromat objectives used in Docuval microscopes) - this creates the best possible combination for Carl Zeiss Jena microscopes with a 160 mm tube length.

This microscope head model is identical to the Baader Mark V binocular viewer used in astronomical telescopes and is often purchased by astronomy enthusiasts and adapted for telescope mounting.

Description of this part for the microscope.

Variant, Cytology, Hematology, Histology, Jenamed-2, Fluorescence)
- Jenapol
- Jenavert
- Jenaval
- Jenatech
- Jenalumar

Please note - this is only the adjustment knob, that is the knob used by the microscope user to make the illumination brighter or dimmer. It is not a potentiometer and therefore not a part of the electrical circuit.

This knob features the characteristic white cap used on Carl Zeiss Jena microscopes, which is often lost during decades of microscope use.

Mechanically, this knob is attached to the potentiometer. The fixing screw is covered by a white metal cap.

In the last photo I indicate with an arrow exactly which element it is and where it is located in a Carl Zeiss Jena Jenamed microscope. In Jenaval and Jenalumar microscopes it is located on the microscope base.

Description of this part for the microscope.

Lichteinstellupe (Centering / Focus telescope)
Mounting diameter: 23.2 mm + original 30 mm adapter

This centering telescope can be used for:
- DIC alignment (Differential Interference Contrast)
- Phase contrast alignment (centering phase rings)
- Aperture diaphragm inspection (iris diaphragm observation)Filament centering when setting up Köhler illumination

This is one of those microscope elements for which many different names are used. Among others:
- phase telescope
- phase contrast telescope
- phase alignment telescope
- phase adjustment telescope
- phase centering telescope
- phase contrast centering telescope
- phase contrast alignment telescope
- phase contrast adjustment telescope
- centering telescope
- condenser centering telescope
- condenser alignment telescope
- condenser adjustment telescope
- alignment telescope
- adjustment telescope
- inspection telescope
- aperture viewing telescope
- back focal plane viewing telescope
- auxiliary microscope
- phase contrast auxiliary microscope
- alignment auxiliary microscope
- centering auxiliary microscope
- adjustment auxiliary microscope
- auxiliary telescope
- centering scope
- alignment scope
- phase scope
- phase viewer
- phase contrast viewer
- phase centering eyepiece
- phase contrast eyepiece
- phase alignment eyepiece
- phase telescope eyepiece
- centering eyepiece
- condenser centering eyepiece
- adjustment eyepiece
- inspection eyepiece

Description of this part for the microscope.

Carl Zeiss Jena microscope heads with a wide field of view (German: Grossfeld) have one eyepiece tube with diopter adjustment and a second one without it. Here I present the tube without diopter adjustment (straight eyepiece tube).

Basic parameters:
- Type: straight eyepiece tube
- Compatible eyepiece diameter: 30 mm
- Colour: white

Compatible with 30 mm microscope heads used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

Description of this part for the microscope.

hand when adjusting the interpupillary distance. It is a rounded metal cover that protects the eyepiece prism located underneath.

The last photo in the gallery shows a complete microscope head. An arrow indicates exactly which component is being described and where it is located inside the head, making it easy to identify.

Carl Zeiss Jena wide field microscope heads (those designed for 30 mm eyepieces) have two such components (two prism covers). They protect the prisms of the right and left eyepieces. Both covers are identical and interchangeable, so there is no constructional difference between the right-hand and left-hand cover.

This is a component for a microscope head, not for a specific microscope model.

This component fits microscope heads designed for 30 mm eyepieces used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Metal cast or injection-moulded components manufactured by Carl Zeiss Jena have their own part numbers. This component is marked with the number 2630 (full designation: Si10 2630 / Si10 CZ 2630). In addition, the number "1" or "2" appears next to the part number to indicate whether it is the cover for the right-hand or left-hand prism. This is the only difference, because mechanically the right-hand and left-hand covers are identical.

Description of this part for the microscope.

the front, in the centre of the binocular head, between the two eyepiece tubes. It is a round cover plate (end cap) carrying a scale from 55 to 75 indicating the interpupillary distance (eyepiece tube spacing).

The last photograph in the gallery shows the complete binocular head. An arrow indicates the exact component being offered and its location within the head, allowing it to be identified unambiguously.

This is a component of the binocular head rather than a component dedicated to a particular microscope model.

This component fits 30 mm eyepiece binocular heads used, among others, on the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Description of this part for the microscope.

microscope head to the microscope.

Basic specifications:
Mount type: dovetail
Diameter: 41 mm, the Carl Zeiss Jena and Lomo standard
Internal thread: 34 mm

The last photograph in the gallery shows a complete binocular head. An arrow indicates exactly which component is being offered and where it is located on the head, making visual identification straightforward.

This is a component of the microscope head rather than of any specific microscope model.

This component fits 30 mm binocular heads used, among others, on the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

This 41 mm Carl Zeiss Jena dovetail mounting standard is commonly used:
- if you want to perform a DIY conversion and mount a microscope head from another manufacturer onto a Carl Zeiss Jena or Lomo microscope
- if you want to connect another dovetail-mounted accessory to a Carl Zeiss Jena or Lomo microscope, such as an Optovar magnification changer, a polarisation intermediate tube, a DIC head or an EPI reflected-light illuminator
- if you want to use the 34 mm internal thread to mount a photographic tube for a camera

Description of this part for the microscope.

17-A
Magnification: 50x
Numerical aperture N.A.: 0.95
Optical correction: Apochromat
Additionally: cover glass thickness correction collar, range 0.12 - 0.22 mm
Tube length: infinity
Thread: M25
Cover glass: yes, required
Immersion: no (so-called dry objective)

Commonly used, cheap cover glasses are 0.17 mm thick mostly on paper. Even the standard for class #1.5 allows a range of 0.16-0.19 mm, and cheap Chinese cover glasses in practice come in anywhere from approx. 0.13 to 0.25 mm, often not matching the thickness stated on the box. Only #1.5H (high precision) cover glasses have a guaranteed thickness of 0.170 mm with a tolerance of +/- 0.005 mm. With high-aperture dry objectives such as this Apochromat 50x/0.95, variation in cover glass thickness noticeably reduces image contrast and resolution (spherical aberration). The correction collar fitted to this objective lets you adjust the optics to the combined thickness of the cover glass and the mounting medium layer beneath it, within a range of 0.12 mm to 0.22 mm. This compensates for most of the variation encountered in practice.

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

As for the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

be attached to a trinocular head or directly to the microscope body, even when there is no trinocular head.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: grey
Tilt angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to the trinocular head or microscope body: ring with a dovetail
Dovetail diameter: 41 mm
Type of connection at the output: empty tube / barrel
Tube diameter at the output: 23.2 mm internal diameter
Length of the barrel / tube: 25 mm
Length adjustment: no - this is not a tube with adjustable height

Since the adapter has an empty barrel with an internal diameter of 23.2 mm on the output side, a projection eyepiece of that diameter can be placed in it, or a so-called "USB eyepiece", that is a digital microscope camera. Adapters between the 23.2 mm barrel and the M42 thread are also widely available, and from the M42 thread you can move on to any other mount: Nikon, Canon, Sony and others.

Such a tube can be mounted directly on the microscope body instead of the head. A dovetail seat with a diameter of 41.0 - 41.5 mm is found, among others, on the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH

It is also often used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can equally well be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol microscopes
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in the LOMO Polam microscopes
- some versions of the intermediate photo tubes for the Carl Zeiss Jena Mikroval series microscopes (others require a tube screwed onto a thread)

This is not a "tube for one specific microscope model". A trinocular head can be mounted not only on the microscope it was sold with - it is therefore correct to assume that this is a universal tube, with a 41 mm dovetail on one side and a 23.2 mm barrel on the other.

The "compatibility" section gives an example list of microscopes this tube fits, although it is not a complete list.

Description of this part for the microscope.

The tube allows a camera or a camera body to be attached to a trinocular head or directly to the microscope body, even when there is no trinocular head.

Basic technical parameters of this tube:
Manufacturer: LOMO (ЛОМО)
Colour: black, rings and barrel chrome-plated
Tilt angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to the trinocular head or microscope body: ring dovetail (male part)
Dovetail diameter: 41 mm
Type of connection at the output: empty tube / barrel
Tube diameter at the output: 23.2 mm internal diameter
Length of the barrel / tube: variable
Length adjustment: yes - the barrel is extendable, with a scale from 140 to 200 mm and a knurled locking ring

This is the version with adjustable tube length. A scale from 140 to 200 mm is engraved on the extendable barrel, with a reference line and intermediate divisions, and the setting is locked with a knurled ring. This gives two things at once. First, a continuous change of the image scale - the longer the tube, the larger the image falling on the sensor or the film, so the framing can be adjusted without changing the objective. Second, and more importantly, the ability to work with objectives computed for different optical tube lengths: 160, 170, 180, 190 and 200 mm. Carl Zeiss Jena and LOMO objectives are computed for 160 mm, Leitz Wetzlar for 170 mm, some objectives of metallurgical and measuring microscopes for 190 or 200 mm - here you simply set the barrel to the right value and the objective works under its design conditions, instead of delivering an image with residual aberration.

Since the adapter has an empty barrel with an internal diameter of 23.2 mm on the output side, a projection eyepiece of that diameter can be placed in it, or a so-called "USB eyepiece", that is a digital microscope camera. Adapters between the 23.2 mm barrel and the M42 thread are also widely available, and from the M42 thread you can move on to any other mount: Nikon, Canon, Sony and others.

Such a tube can be mounted directly on the microscope body instead of the head. A dovetail seat with a diameter of 41.0 - 41.5 mm is found, among others, on the microscopes:
- LOMO
- Carl Zeiss Jena
- Meopta
- IOR
- Reichert Biopan
- Olympus CH

It is also often used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The "compatibility" section gives an example list of microscopes this tube fits, although it is not a complete list.

The last photo shows a LOMO Erudit microscope with this photo tube and a projection eyepiece mounted. It is an example of use.

Description of this part for the microscope.

camera to a trinocular head or directly to the microscope stand, even when there is no trinocular head at all.

This is a black tube with an upper element (barrel) 55 mm long. Here (https://www.microscopeparts.eu/gallery/91057) you can see a functionally identical adapter, but grey and with an upper barrel only 25 mm long.

Black adapters of this kind come from the era of the Carl Zeiss Jena L stands (models Carl Zeiss Jena Lg, Lumipan, Ng, Nf or Nu). The grey ones are newer, from the era of the Mikroval series (models Carl Zeiss Jena Laboval, Eduval, Ergaval or Amplival and Docuval).

The mounting fit is of course identical, so both can be used interchangeably.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: black
Inclination angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to a trinocular head or microscope stand: ring dovetail
Ring dovetail diameter: 41.5 mm
Type of connection at the output: empty barrel / tube
Tube diameter at the output: 23.2 mm inner diameter
Barrel / tube length: 55 mm
Tube length adjustment: no - this is not a height-adjustable tube

Because on the output side this adapter has an empty barrel with an inner diameter of 23.2 mm, you can place in it a projection eyepiece of that diameter or a so-called USB eyepiece, that is a digital microscope camera. In addition, adapters between the 23.2 mm barrel and the M42 thread are widely available, and from the M42 thread you can already move on to any other mount: Nikon, Canon, Sony and all the rest.

Such a tube can be mounted directly on the microscope stand, in place of the head. A seat for a ring dovetail of 41.0 - 41.5 mm diameter is found among others in the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH
- Gamma

It is also used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can likewise be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the microscopes Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in LOMO Polam microscopes
- some versions of the black intermediate photo tubes for the microscopes Carl Zeiss Jena Lg / Lumipan / Nf and of the grey ones from the Mikroval series (others require a tube that screws in on a thread)

This is not a tube for one particular microscope model. A trinocular head can be mounted not only on the microscope it was sold with, so the correct assumption is that this is a universal tube with a ring dovetail of 41.5 mm diameter on one side and a barrel of 23.2 mm diameter on the other.

In the compatibility section you will find an example list of microscopes this tube fits, although that list is not complete.

Description of this part for the microscope.

Jena
Inscription: logo "Carl Zeiss Jena" and text "Q1 MADE IN DDR"
Material: aluminium
Length: 52 mm
Width: 14 mm
Mounting: the nameplate is glued on

By default such a nameplate was fitted to most Carl Zeiss Jena microscopes from the Mikroval series onwards. There is also a smaller nameplate - with the manufacturer logo only (without the "Q1 Made in DDR" text). You can see it here: https://www.microscopeparts.eu/part/00604.

Because the adhesive used to attach these plates to the microscope body loses its properties over the years, these plates very often fall off. A nameplate like this makes it possible to restore the factory appearance of a microscope using original parts.