Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

Mikroval series:
- Eduval
- Laboval
- Ergaval
- Amplival (the entire series, including Epival, Vertival, Amplival-Pol)
- Fluoval
- Metaval
- Telaval
- and even Epignost

Description of this part for the microscope.

11505193

Description of this part for the microscope.

This is only the HOUSING. Inside the housing there are:
- an on off switch
- a potentiometer for adjusting the light intensity
- a cooling fan including its electrical wiring

Once again: this is not a complete illuminator. There are no optical components and no electronic boards inside, except for the circuitry that operates the fan.

Description of this part for the microscope.

except for the circuitry that operates the LCD.

Description of this part for the microscope.

Description of this part for the microscope.

molded parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the number 2580 (full designation: Si10 CZ 2580).

This is a service element (replacement part) for the trino head (head with photo output), suitable for Carl Zeiss Jena CF-250 microscopes. Please note that this is a microscope element for a microscope part (the trinocular head) and not a part for a specific microscope model.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the upper main part of the housing is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this housing DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the head, in order to clearly identify this part.

Many different names are commonly used for the trino head. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trino head
- trinocular head
- trinocular head unit
- photo dome
- photo tube
- inclined tube with photo output

Description of this part for the microscope.

assembly of two lenses
- knob for moving and shifting the lenses
- mechanism for moving and shifting the lenses

Metal, cast or injection-molded parts manufactured by Carl Zeiss Jena have their own identification numbers. In this mechanism the lens is mounted on a cast part marked with number 2582 (full marking: Si10 CZ 2582).

This is a service element (repair part) of the trinocular head (photo tube), suitable for Carl Zeiss Jena microscopes of the CF-250 series. Please note that this is an element (component) of a microscope part (German: "Fototubus") and not a part dedicated to a specific microscope model.

Carl Zeiss Jena microscopes of the CF-250 series have a modular design and the microscope part to which the eyepieces are mounted (commonly referred to as "head", "binocular" or "twin tube") is a separate element from the angle tube (sometimes the German term "Winkeltubus" is used). If the angle tube has a photographic output, it is referred to as a "photo tube". The Bertrand lens offered and described here is intended specifically for this microscope part.

Hinweis - Carl Zeiss Jena microscopes Jenapol and Jenatech, although they also belong to the CF-250 series, have a differently designed photographic output and this mechanism DOES NOT FIT these models.

Hinweis - Carl Zeiss Jena also produced a simplified version of the photo tube which does not contain a Bertrand lens inside. In the image gallery there is also a page from the manufacturer's catalog so that it is visible whether these versions differ externally in appearance. This Bertrand lens shown and offered here CANNOT be installed in such a simplified version of the photo tube.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is concerned and where it is located in the head, in order to clearly identify this part.

In common usage many names are used for the photo tube. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trinocular head
- trinocular microscope head
- trinocular head assembly
- photo dome
- inclined tube with photo output

Description of this part for the microscope.

250 series microscopes.
Note that this element is a component of a microscope element (the angled tube) and not a part dedicated to a specific microscope model.

This element fits, among others, the following Carl Zeiss Jena microscopes from the CF-250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenavert
- Jenatech
- Jenapol

Important: the element DOES NOT INCLUDE the screw used to secure the microscope head.

Inside this element there is a protective glass (without its own magnification, so called "zero lens") with a violet anti-reflection coating.
Although this holder for the binocular microscope head and the holder located at the photographic port look the same, have the same dimensions and are mechanically compatible - they are NOT (!) identical.
- the binocular microscope head mount contains a protective glass with a violet anti-reflection coating
- the mount located at the photographic port contains a protective glass with a green anti-reflection coating.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

250 series microscopes.
Note that this element is a component of a microscope element (the angled tube with photo port) and not a part dedicated to a specific microscope model.

This element fits, among others, the following Carl Zeiss Jena microscopes from the CF-250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenavert
- Jenatech
- Jenapol

Important: the element DOES NOT INCLUDE the screw used to secure the microscope head.

Inside this element there is a protective glass (without its own magnification, so called "zero lens") with a green anti-reflection coating.
Although this holder at the photographic port and the holder for the binocular microscope head look the same, have the same dimensions and are mechanically compatible - they are NOT (!) identical.
- the binocular microscope head mount contains a protective glass with a violet anti-reflection coating
- the mount located at the photographic port contains a protective glass with a green anti-reflection coating.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

Description of this part for the microscope.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the element is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this part DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos.

Description of this part for the microscope.

suitable for Carl Zeiss Jena CF-250 microscopes. Please note that this is a microscope element for a microscope part (the trinocular head) and not a part for a specific microscope model.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the prism carrier is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this part DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the head, in order to clearly identify this part.

Many different names are commonly used for the trino head. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trino head
- trinocular head
- trinocular head unit
- photo dome
- photo tube
- inclined tube with photo output

Description of this part for the microscope.

used, for example, in microscopes from Carl Zeiss Jena of the Mikroval series:
- Eduval
- Laboval
- Ergaval
- Amplival (entire series including Epival, Vertival, Amplival-Pol)
- Fluoval
- Metaval
- Telaval
- even Epignost

In microscope models with fluorescence illumination (e.g. Laboval Fluoreszenz or Fluoval), a filter wheel is installed in this head. When the manufacturer installed this head in other microscope models - a blanking plug was placed instead of the filter wheel - and this is exactly the element shown here.

Over the years, this element is very often lost and on the secondary market there are many such photo trino adapters without the blanking plug. The lack of this blanking plug can cause even large contaminants to enter the optics.

Description of this part for the microscope.

Due to the similar design, it is very likely that this component will also fit the photographic trinocular head of the following macroscope models:
- Wild M400
- Wild M450 (another name: Leica M450)

The macroscope is an advanced stereoscopic microscope with a high-resolution ZOOM objective.

Why are dual names Wild and Leica used? The M400 macroscope was manufactured by Wild Heerbrugg (Switzerland). Later, the Wild company was acquired by Leica and the M420 and M450 models may be labeled either Wild M420 / Wild M450 or Leica M420 / Leica M450. Note: this is different for the Wild M400 model - it does not have a Leica equivalent, because "Leica M400" is a model of a surgical microscope.

This microscope part may solve the following problems occurring in a Wild Heerbrugg M400, M420 oder M450 macroscope:
- missing eyepiece tube in the macroscope
- eyepiece cannot be inserted into the tube
- eyepiece tube in the macroscope is deformed

Description of this part for the microscope.

with a high-resolution ZOOM objective.

Description of this part for the microscope.

this component will also fit the photographic trinocular head of the following macroscope models:
- Wild M400
- Wild M450 (another name: Leica M450)

The macroscope is an advanced stereoscopic microscope with a high-resolution ZOOM objective.

Why are dual names Wild and Leica used? The M400 macroscope was manufactured by Wild Heerbrugg (Switzerland). Later, the Wild company was acquired by Leica and the M420 and M450 models may be labeled either Wild M420 / Wild M450 or Leica M420 / Leica M450. Note: this is different for the Wild M400 model - it does not have a Leica equivalent, because "Leica M400" is a model of a surgical microscope.

Description of this part for the microscope.

this component will also fit the photographic trinocular head of the following macroscope models:
- Wild M400
- Wild M450 (another name: Leica M450)

The macroscope is an advanced stereoscopic microscope with a high-resolution ZOOM objective.

Why are dual names Wild and Leica used? The M400 macroscope was manufactured by Wild Heerbrugg (Switzerland). Later, the Wild company was acquired by Leica and the M420 and M450 models may be labeled either Wild M420 / Wild M450 or Leica M420 / Leica M450. Note: this is different for the Wild M400 model - it does not have a Leica equivalent, because "Leica M400" is a model of a surgical microscope.

Description of this part for the microscope.

intended for the repair or replacement of the mounting holders into which the eyepiece tubes are screwed in the head of the Wild Heerbrugg M420 Makroskop (macroscope) (Leica M420).

Due to the similar design, it is very likely that this component will also fit the photographic trinocular head of the following macroscope models:
- Wild M400
- Wild M450 (another name: Leica M450)

The macroscope is an advanced stereoscopic microscope with a high-resolution ZOOM objective.

Why are dual names Wild and Leica used? The M400 macroscope was manufactured by Wild Heerbrugg (Switzerland). Later, the Wild company was acquired by Leica and the M420 and M450 models may be labeled either Wild M420 / Wild M450 or Leica M420 / Leica M450. Note: this is different for the Wild M400 model - it does not have a Leica equivalent, because "Leica M400" is a model of a surgical microscope.

The head of this microscope contains two such holders - one for each eyepiece tube. Both are identical, which means there is no difference between the right and left side.

Description of this part for the microscope.

and related models.

This element is used when transmitted light is temporarily not needed. The illuminator itself does not need to be removed - instead, the light output should simply be completely blocked, and this light output is the collector lens itself. This collector lens is located inside the microscope base, above the angle mirror and below the condenser.

When can there be a need to completely block transmitted light? Most often when:
- a microscope with DIA illumination (transmitted light) and EPI illumination (reflected light) is available, but temporarily only reflected light operation is needed
- a microscope previously working with transmitted light (for example Carl Zeiss Jena Amplival) is being converted into a microscope intended to work permanently only with reflected light (for example converting an Amplival into a Vertival)
- for example a Fluoval microscope is used and it is undesirable that "the lower light is visible"

This element fits the following microscopes:
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Interphako
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Docuval

The photo gallery contains detailed photos of this element from different sides, while the video (in the video gallery) shows exactly how this blanking plug is used and where it is mounted.

Description of this part for the microscope.

objective nosepiece. It consists of slots (empty openings) into which filter sliders are inserted. This is the component that the Microscopy-UK portal (https://www.microscopy-uk.org.uk/mag/imgmar09/JenamedFinal.pdf) referred to as "in-tube filter holders".

This filter holder is compatible with the following Carl Zeiss Jena microscopes:
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

Metal, cast, and injection-moulded parts manufactured by Carl Zeiss Jena have their own identification numbers. This part bears the number: 2709/2 (full designation: Si10 CZ 2709/2).

Mechanically, this "block with empty slots" is attached to the casting numbered Si10 CZ 2708, which is the objective nosepiece block.

In the last photo of the gallery, I use an arrow to show exactly which component is being described.

Description of this part for the microscope.

hand when adjusting the interpupillary distance. It is a rounded metal cover that protects the eyepiece prism located underneath.

The last photo in the gallery shows a complete microscope head. An arrow indicates exactly which component is being described and where it is located inside the head, making it easy to identify.

Carl Zeiss Jena wide field microscope heads (those designed for 30 mm eyepieces) have two such components (two prism covers). They protect the prisms of the right and left eyepieces. Both covers are identical and interchangeable, so there is no constructional difference between the right-hand and left-hand cover.

This is a component for a microscope head, not for a specific microscope model.

This component fits microscope heads designed for 30 mm eyepieces used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Metal cast or injection-moulded components manufactured by Carl Zeiss Jena have their own part numbers. This component is marked with the number 2630 (full designation: Si10 2630 / Si10 CZ 2630). In addition, the number "1" or "2" appears next to the part number to indicate whether it is the cover for the right-hand or left-hand prism. This is the only difference, because mechanically the right-hand and left-hand covers are identical.

Description of this part for the microscope.

It is its UPPER HOUSING PART.
There are no cables, circuit boards or buttons inside.

The last photos in the gallery show where this cover was taken from. There you will see:
- the complete Zeiss Axiovert Bedienpult 45 17 49 unit (the number is also written as 451749), with an arrow pointing to this very housing part
- the nameplate of the whole unit