Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

RMS
Tubus length: 160 mm
Focal length: 45 mm
Immersion: no (dry, air)
Info: PHACO1 Phase Contrast

Description of this part for the microscope.

is still in a liquid state.

Of course, the oil is usable, but I think this item has more collector's value.

Description of this part for the microscope.

65
Leitz P/N: 519759
Magnification: 40x
Numerical aperture: 0.65
Cover glass: yes, 0.17 mm
Thread: RMS
Tube length: 160 mm
Focal length: 45 mm
Immersion: no (dry, air)
Info: phase contrast PHACO 2

The same objective model was also sold under the name "Leica" instead of "Leitz" on the housing, so these are in fact identical objectives. This objective also fits Will Wetzlar microscopes.

Description of this part for the microscope.

Wetzlar
Model: 160/0,17 EF 100/1.25 OEL PHACO 3
Magnification: 100x
Correction: semi-plan achromat
Numerical aperture: 1.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm
Immersion: yes, oil
Thread: RMS
Specimen protection: yes - spring-loaded
Info: PHACO 3 = phase contrast

Some important information about this objective:
- the designation "EF" means "Extended Field" - this is a semi-plan achromatic objective with an 18 mm field of view, which should be taken into account when selecting suitable eyepieces
- the semi-plan achromatic correction is "almost flat" - it is no longer an achromat, but not yet a plan achromat
- this objective can be used in brightfield, but phase contrast operation requires a compatible phase contrast condenser or a slide (slider) with a phase ring diaphragm
- the designation PHACO 3 means that for phase contrast operation a phase contrast condenser set to ring "3" should be used (the equivalent setting used by Zeiss is called "Ph3")
- this objective can be used with microscopes designed for objectives with a 170 mm tube length, but in such a case the optical path must be extended by 10 mm - most commonly by pulling the eyepieces out of the tubes by 10 mm

This objective can be used with any microscope from any manufacturer together with a compatible phase contrast condenser. Naturally, the microscope must be compatible, i.e. it must support RMS objectives, TL=160 mm and FL=45 mm - or have adapters that make such adaptation possible (for example thread adapters).

Description of this part for the microscope.

from a Leitz Dialux microscope. In the last photo in the gallery you can see the microscope stage from which it was removed. However, the manufacturer fitted the same type of mechanical XY microscope stage to many other Leitz microscope models, so this specimen holder is also compatible with models other than the Leitz Dialux.

When determining compatibility and whether this specimen holder can be mounted on a particular mechanical XY microscope stage, the following dimensions are critical:
- distance between the two side locating pins: 81 mm measured from the outer edge of one pin to the outer edge of the other pin
- locating pin diameter: 3 mm each
- therefore, the centre-to-centre distance between the locating pins is 78 mm
- diameter of the central mounting screw: 4 mm
- position of the mounting screw: centred between the two locating pins

If the spacing of the locating pins matches, this specimen holder can also be mounted on microscope stages made by other manufacturers.

Leitz Wetzlar produced specimen holders with fixed stage clips as well as versions with a spring-loaded stage clip. Here I am showing and offering the spring-loaded version.

On the used market and in technical documentation, this microscope part is described using a variety of names. Common terms include:
- specimen holder
- microscope stage specimen holder
- mechanical stage specimen holder
- slide holder
- microscope slide holder
- microscope slide clamp
- spring-loaded specimen holder
- spring-loaded slide holder
- spring-loaded stage clip
- specimen clamp
- specimen carrier
- mechanical stage carrier
- XY stage specimen holder
- specimen holder for mechanical XY microscope stage
- stage holder
- stage clip assembly

The photographs in the gallery show the exact dimensions of the microscope part offered here. In addition, the last photograph includes an arrow indicating exactly which microscope part is being described and where it is mounted on the mechanical XY microscope stage, making identification straightforward. The accompanying video demonstrates the operation of the spring-loaded stage clip.

Description of this part for the microscope.

allowing precise movement of the specimen in both the X and Y axes of the stage plane. The manipulator consists of two coaxial knobs, two independent drive shafts and the fixing elements that attach it to the stage mechanism.

This particular manipulator was removed from a Leitz Dialux microscope. The last photograph in the gallery shows the entire microscope stage from which it was dismounted. The manufacturer also used the same or very similar stages in many other Leitz Wetzlar microscope models, which is why the manipulator may also be compatible with other models from this company.

On the second-hand market and in service documentation one encounters many names referring to this assembly. The most commonly used terms include, among others:
- stage manipulator
- XY stage manipulator
- mechanical stage drive
- stage control knobs
- specimen mover
- coaxial stage drive
- stage drive assembly
- mechanical stage control
- manual XY stage drive
- stage actuator mechanism

Such manipulators very often suffer mechanical damage during transport of the microscope. Because they protrude beyond the outline of the stand, it is precisely they that absorb the impact energy first - in the event of a fall or improper packaging of the instrument.

In many cases it is not the entire manipulator that is damaged, but only one of its components. Most often these are the knobs, the drive shafts, the coaxial sleeves or the fixing elements. For this reason, this database also contains all the most important constituent parts of this (and other) manipulators, offered separately as service elements.

Damage to the manipulator does not make further work with the microscope impossible. The specimen can be moved by hand, or a simple specimen holder without an XY movement mechanism can be fitted. Such a solution works well at low magnifications; however, when working with objectives of magnifications greater than 40x (e.g. 60x, 63x, 80x or 100x), precise manual movement of the specimen becomes very difficult. At total magnifications exceeding about 400x, even a slight movement of the hand shifts the image by a considerable distance within the field of view. The mechanical manipulator enables very smooth, controlled and repeatable movement of the specimen in both axes, which is particularly important during observation with oil immersion and when producing photographic documentation.

The photographs in the gallery show the exact dimensions of the complete manipulator. The last photograph presents the entire microscope stage together with an arrow indicating the mounting location of this element, which makes it possible to identify the offered part unambiguously.

Description of this part for the microscope.

not intended for so-called "thick" objectives
Thread in the cap: no, the cap of this objective case does not contain a thread for attaching an RMS objective

This objective case can be used to store so-called "short" objectives (DIN 33 mm), longer objectives (DIN 37 mm), and long objectives (DIN 45 mm), provided they are not the so-called "thick" type.

Various names are used on the secondary market for a microscope objective case, including:
- objective case
- microscope objective case
- objective container
- microscope objective container
- objective storage case
- objective storage container
- objective box
- objective storage box
- protective objective case
- objective lens case
- objective lens container
- dust protection case
- transport case for microscope objectives
- microscope objective holder case
- storage canister for microscope objectives

Each case has the Leitz Wetzlar logo on its cap.

Although this case is of greatest interest to users and collectors of objectives made by the manufacturer Leitz Wetzlar, it can of course be used to store objectives from any manufacturer.

Description of this part for the microscope.

17 100/1.25 Oel
Catalogue number in the manufacturer's catalogue: 519756
Numerical aperture N.A.: 1.25
Cover glass: yes, 0.17 mm
Thread: RMS
Tube length: 160 mm
Parfocal length: 45 mm (so-called long barrel objective)
Immersion: yes, oil

This is the so-called "black series" of objectives, named after the black plastic housing of the objective. They were used mainly in Leitz Wetzlar HM-LUX-3 microscopes (and in the model signed Leica HM-LUX 3). This was the period when manufacturers were experimenting with a new look for microscope parts, and exactly the same kind of "black series" could also be found in Will Wetzlar V300 / V355 / V365 or Nikon Alphaphot YS2 microscopes.

This objective fits practically any microscope from any manufacturer, provided it has an RMS thread and accepts objectives with a tube length of 160 mm and a parfocal length of 33 / 37 or 45 mm. A few such microscopes are listed as examples in the "compatibility" section, but this is not a complete list.

Description of this part for the microscope.

25
Catalogue number in the manufacturer's catalogue: 519754
Numerical aperture N.A.: 0.25
Cover glass: not required
Thread: RMS
Tube length: 160 mm
Parfocal length: 45 mm (so-called long barrel objective)
Immersion: no (dry objective)

This is the so-called "black series" of objectives, named after the black plastic housing of the objective. They were used mainly in Leitz Wetzlar HM-LUX-3 microscopes (and in the model signed Leica HM-LUX 3). This was the period when manufacturers were experimenting with a new look for microscope parts, and exactly the same kind of "black series" could also be found in Will Wetzlar V300 / V355 / V365 or Nikon Alphaphot YS2 microscopes.

From 1990 onwards, the logo (and the name) "Leica" began to appear on microscopes that had until then been signed "Leitz". This was also visible on the HM-LUX 3 microscope - and this microscope can be found both with the "Leitz" logo and with "Leica". The same 10x objective that I present here with the name "Leitz Wetzlar" and manufacturer number 519754 also exists with the "Leica" marking - and NOTE - it carries exactly the same number, that is "519754".

This objective fits practically any microscope from any manufacturer, provided it has an RMS thread and accepts objectives with a tube length of 160 mm and a parfocal length of 33 / 37 or 45 mm. A few such microscopes are listed as examples in the "compatibility" section, but this is not a complete list.

Description of this part for the microscope.

microscopes have a standardized mount of 38 mm diameter into which various tubes can be fitted. One of exactly these tubes is presented here.

Basic parameters of the tube presented here:
Markings on the housing: "Germany" on one side and "30ø" on the other side
Mounting connection: a plain tube (cylinder). This is not a tube with a thread or a dovetail
Mounting diameter: 38 mm, that is the standard mounting diameter used in Leitz Wetzlar trinocular heads
Internal optics: none - this tube has no optics inside
Internal diameter: the tube has an internal diameter of 30 mm, so that a projection eyepiece of exactly that diameter can be fitted inside

The trinocular heads this tube fits are used among others in the following microscopes:
- Leitz Wetzlar Orthoplan
- Leitz Wetzlar Diaplan
- Leitz Wetzlar Ergolux
- Leitz Wetzlar Dialux
- Leitz Wetzlar Laborlux
- Leitz Wetzlar SM-LUX
- Leitz Wetzlar Ortholux II
- Leitz Wetzlar Aristoplan
- Leitz Wetzlar HM-LUX

This is not a tube for one particular microscope model. A trino head can be mounted not only on the microscope it was sold with, so the correct assumption is that this is a standard tube for Leitz Wetzlar trinocular heads - and those can be used on most microscope models of this company.

The last photo in the gallery shows what this tube looks like with a 30 mm eyepiece fitted.

The "compatibility" section lists example microscopes this tube fits, although the list is not complete.