Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

filter is exceptionally rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

transmitted light is inserted. Inside there is a lens that collimates the light beam. In the lower part of this element there are three filter holders and a shutter that allows complete cutoff of this light source.

The illumination block in the Carl Zeiss Jena Fluoval-2 fluorescence microscope is modular, and each of its elements can be easily detached and attached. This microscope element is mounted to the whole module using screws and the key https://www.microscopeparts.eu/part/00588.

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

10 160/-
Color correction: Planachromat
Numerical aperture: 0.10
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Color correction: Planachromat
Numerical aperture: 0.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.32
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 1,25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: HI = Homogene Immersion, also oil immersion

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

(and its variants: Fluoval, Epival, Vertival)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

Both the left and the right knob are identical, but when installing be careful about the screw length, as they may differ).

VERY IMPORTANT: although the right and left knobs are identical - different screws are used to attach them.

Lengths of screws used to attach the knobs in Carl Zeiss Jena Ergaval and Amplival microscopes:
- left fine adjustment knob (micro): 1 pc. screw 12 mm
- left coarse adjustment knob (macro): 3 pcs. screws 8 mm
- right fine adjustment knob (micro): 1 pc. screw 16 mm
- right coarse adjustment knob (macro): 3 pcs. screws 12 mm

Over the years these plastic knobs are often damaged:
- sometimes they crack due to impact or improper transport securing
- often they are partially melted by a soldering iron, light bulb or even a cigarette
- sometimes they are damaged during attempts to remove them

Description of this part for the microscope.

Amplival (and its variants: Fluoval, Epival, Vertival)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

Both the left and the right knob are identical, but when installing be careful about the screw length, as they may differ).

VERY IMPORTANT: although the right and left knobs are identical - different screws are used to attach them.

Lengths of screws used to attach the knobs in Carl Zeiss Jena Ergaval and Amplival microscopes:
- left fine adjustment knob (micro): 1 pc. screw 12 mm
- left coarse adjustment knob (macro): 3 pcs. screws 8 mm
- right fine adjustment knob (micro): 1 pc. screw 16 mm
- right coarse adjustment knob (macro): 3 pcs. screws 12 mm

Over the years these plastic knobs are often damaged:
- sometimes they crack due to impact or improper transport securing
- often they are partially melted by a soldering iron, light bulb or even a cigarette
- sometimes they are damaged during attempts to remove them
- sometimes, when the grease has dried out, the user tries to move the knob using pliers and damages it

Description of this part for the microscope.

Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the left clamp, which does have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

microscopes:
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the right clamp, which does have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the left clamp, simple, which does NOT have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

meaning the shaft with focusing knobs mounted on both ends on the sides of the microscope. Part of this shaft contains a toothed rack, or more precisely speaking, it is a toothed shaft. In the item shown and offered here, the fine focus knob (micro focus) is mounted on the left end of the shaft. Please note that the left and right knobs are identical - however, screws of different lengths are used to attach them: the left knob is attached with a 12 mm screw, while the right knob uses a 16 mm screw. Detailed information about the screws used to attach the coarse and fine focus knobs can be found here: https://www.facebook.com/MikroskopyPZO/posts/pfbid0x2tFPHAEqjn4B7BRsvm2vAt9yyuuSM836QS6K4951GqeUFpU2FJH8YXfFFxbz3cPl

Such focus shafts are used in the following microscopes:
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival (and its variants: Fluoval, Epival, Vertival, Interphako)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

This coarse and fine focus shaft may help solve the following problems in Carl Zeiss Jena Ergaval / Amplival microscopes and related models:
- if the shaft became bent, causing a noticeable jump while rotating it (a very common failure)
- if the screw holding the fine focus knob broke off or snapped, leaving part of the screw inside the shaft
- if the left fine focus knob is missing or damaged
- if the thread on the right or left end of the shaft, where the fine focus knobs are attached, is damaged
- if the toothed rack on the shaft (because such a shaft is effectively a toothed shaft) becomes damaged

Description of this part for the microscope.

for taking microscope photographs or recording microscope videos. This is a gray photographic adapter.

Basic technical parameters:
- mounting connection to microscope stand: 41 mm dovetail
- output connection type on the photo port: 49 mm internal thread
- connection for binocular head mounting: Jena standard 41 mm dovetail
- magnification directed to the binocular head: 1.6x
- magnification on the photo output: none (that is 1.0x)

Because this photo head has a 49 mm threaded output, virtually any device, camera, adapter, tube or other accessory can be connected after using an appropriate 49 mm thread adapter. Direct projection technique may be used (because there is no additional optics inside), or any projection eyepieces may be installed in the optical path.

This photographic attachment is intended mainly (but not exclusively) for the following microscope models:
- Carl Zeiss Jena Eduval
- Carl Zeiss Jena Laboval
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Telaval
- Carl Zeiss Jena Pictoval
- Carl Zeiss Jena Epignost

The list above contains Mikroval series microscopes with gray housings - just like the tube shown and offered here. However, it also works with older black Carl Zeiss Jena microscopes:
- Carl Zeiss Jena L-Stativ (models Lg, Lu and Lr)
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Ng
- Carl Zeiss Jena Nf (and NfPk)

Please note that microscopes from other manufacturers also use the 41 / 41.5 mm dovetail connection standard. Because of this, this photographic head can also be used with microscopes made by:
- Lomo (for example Lomo Biolam)
- Meopta
- IOR
- selected Reichert microscopes (for example Reichert Neozet)
- Will Wetzlar
- Hund Wetzlar
- Leitz Wetzlar

This Carl Zeiss Jena tube is also very often used with microscopes having a larger head mounting diameter. In such cases users apply additional spacer or thickening rings. Because of this, this photo adapter also fits microscopes from manufacturers such as:
- PZO (for example the PZO Biolar model with 43 mm connection)
- Olympus (for example the Olympus CH model with 42 mm connection)

The element that allows a photographic camera or imaging camera to be connected to Carl Zeiss Jena Mikroval series microscopes may be referred to by different names. Commonly used names include:
- trino head
- trinocular head
- photo head
- photographic head
- photo attachment
- photographic attachment
- photo adapter
- photographic adapter
- photo tube
- photographic tube
- phototube
- photographic angle tube
- and various combinations of the words head, attachment, adapter or tube with terms such as photo, photographic, for camera and similar

Description of this part for the microscope.

Jena
Name: Grossfeld Binocular
Eyepiece mounting diameter: 30 mm
Microscope mount: 41 mm dovetail mount
Diopter adjustment: yes, for one eyepiece

The set also includes two eyepieces:
- Model: Carl Zeiss Jena GF-Pw 10x (25)
- Mounting diameter: 30 mm

This head is most commonly used in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, widefield binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older Mikroval series microscopes (for example Ergaval and Amplival). If the microscope is additionally equipped with GF-Planachromat series widefield objectives (or GF-Planapochromat objectives used in Docuval microscopes) - this creates the best possible combination for Carl Zeiss Jena microscopes with a 160 mm tube length.

This microscope head model is identical to the Baader Mark V binocular viewer used in astronomical telescopes and is often purchased by astronomy enthusiasts and adapted for telescope mounting.

Description of this part for the microscope.

Zeiss Jena
Model: Apl 1.4
Holder name according to the manufacturer's catalogue: Kondensor-Einhänger mo
Condenser name according to the manufacturer's catalogue: Aplanatischer Kondensor 1.4 mo / ms
Version: grey version from a Carl Zeiss Jena Ergaval microscope (as opposed to the black version used, for example, on Carl Zeiss Jena Nf microscopes)
Numerical aperture N.A.: 1.4
Aperture diaphragm: yes, mounted in the condenser holder
Wide-field lens: yes, swing-out type
Removable top lens: yes, unscrewable
Mounting diameter: the optical section (the condenser without the iris diaphragm) has a mounting diameter of 39.5 mm and can be unscrewed from the condenser holder

The complete assembly consists of the following components:
- upper Apl 1.4 lens
- removable condenser (mo / ms)
- iris diaphragm attached to the condenser holder
- condenser holder mo
- swing-out wide-field lens
- two centring screws

The last photograph in the gallery shows a page from the manufacturer's original catalogue. Arrows indicate both this exact condenser holder model and the matching condenser.

Mechanically, this condenser is mounted using a dovetail guide located beneath the microscope stage. On the Carl Zeiss Jena Ergaval this is a separate condenser mounting assembly, while on the Carl Zeiss Jena Amplival the dovetail is integrated into the microscope stage support assembly.

Description of this part for the microscope.

unscrewed. It is mounted onto the dovetail guide located underneath the microscope stage carrier and secured with a clamping screw.

Carl Zeiss Jena Ergaval microscopes were originally equipped with a condenser attached to the "MO" holder. This holder has a permanently mounted iris diaphragm and wide-field lens, while the condenser itself is screwed into the upper thread. In this configuration, the condenser cannot be exchanged.
The Carl Zeiss Jena Fluoval uses a similar arrangement, whereas the Carl Zeiss Jena Amplival was originally equipped with a panchromatic condenser.

If the user wishes to use other condensers (including those made by manufacturers other than Carl Zeiss Jena), the original condenser holder must be replaced with the MZ condenser holder. Once this has been done, any microscope condenser with a mounting diameter of 39.5 mm can be installed. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

This is exactly such a holder for interchangeable condensers.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: grey, the version manufactured for the Mikroval microscope series
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this component is grey, it is also compatible with older black Carl Zeiss Jena microscopes from the 1950s and 1960s (it simply will not look completely original unless it is repainted).

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of condenser holder, making it easy to identify the component.

Description of this part for the microscope.

unscrewed. It is mounted onto a dovetail guide located underneath the microscope stage carrier. The condenser holder is secured to the guide with a clamping screw.

It can accommodate any microscope condenser with a mounting diameter of 39.5 mm, regardless of the manufacturer. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: black, the version manufactured for the black Carl Zeiss Jena microscopes from the 1950s and 1960s
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this microscope component is black, it is also compatible with the newer grey Carl Zeiss Jena microscopes of the Mikroval series.

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of the condenser holder, making it easy to identify the component.

Description of this part for the microscope.

reflector, performs two functions:
- it contains a barrier filter (emission filter) for the 450 nm wavelength
- it acts as an angular mirror, reflecting the light beam from the EPI fluorescence illuminator vertically downward through the objective toward the specimen.

This fluorescence filter cube fits the following EPI fluorescence microscopes:
- Carl Zeiss Jena Fluoval Fluoreszenz
- Carl Zeiss Jena Fluoval-2 (built on the Carl Zeiss Jena Amplival microscope platform)

Important - this microscope component does not fit the first version of the Carl Zeiss Jena Fluoval microscope. The Fluoval microscope (without "2") does not use a filter cube. Instead, it has a simple permanently mounted swing-out barrier filter.

The filter cube has two positions:
- empty, for normal transmitted-light operation
- 450 nm for reflected-light fluorescence (EPI) operation

Mechanically, this filter cube is installed between the objective nosepiece and the microscope head. It slides into a dedicated slot and moves along a dovetail guide. On the Carl Zeiss Jena Laboval Fluoreszenz microscope, this slot is located in the additional upper horizontal arm of the EPI fluorescence illuminator. On the Carl Zeiss Jena Fluoval-2 microscope, the slot is located in the EPI fluorescence arm, which is an integral part of the microscope. The Fluoval-2 is based on the Carl Zeiss Jena Amplival microscope, which has a modular design. Mechanically, the Fluoval-2 is essentially an Amplival equipped with an upper EPI fluorescence arm.

Sliding the cube along this dovetail guide switches between the empty position (transmitted light) and EPI fluorescence with the 450 nm filter.

Description of this part for the microscope.

diameter: 23.2 mm

This eyepiece allows the microscope image to be projected onto a surface such as a wall, ceiling or projection screen.

Originally, this eyepiece model was supplied with the Carl Zeiss Jena Pictoval projection microscope. It can also be installed on virtually any microscope from any manufacturer with a 23.2 mm eyepiece tube.

Important: Projecting a microscope image requires a very large amount of light, so a high-power illuminator is necessary.

Description of this part for the microscope.

head in Carl Zeiss Jena Pictoval projection microscopes (microprojectors). The adjustable tilt angle of the eyepiece tube, which held a projection eyepiece (usually f=100), allowed the position of the projected image on the projection surface to be changed.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Eyepiece mounting diameter: 23.2 mm
Mounting to the microscope arm: 41 mm diameter dovetail ring

Because this microscope head has a Carl Zeiss Jena standard microscope mount (a 41 mm diameter dovetail ring), it can be mounted on most microscopes from this manufacturer (e.g. Carl Zeiss Jena Eduval, Laboval, Ergaval, Amplival, etc.), as well as on microscopes made by Lomo (e.g. Lomo Biolam), IOR and Meopta.

It seems useful to mention a few points:
- never look through this microscope head with the naked eye if a projection eyepiece is installed in it and the head is mounted in a Carl Zeiss Jena Pictoval microprojector. This may result in loss of eyesight due to the very high light output emitted by this microscope
- when mounting this microscope head on a microscope other than a Carl Zeiss Jena Pictoval, a different magnification scale may be obtained than with the original heads designed for the particular microscope model
- projecting a microscope image requires a great deal of light, i.e. a powerful illuminator. This is worth remembering if you intend to use this head to project an image from biological microscopes with standard incandescent illumination (e.g. 15 W 6 V), which is definitely not sufficient
- visual observation using this microscope head may be inconvenient because it has a different (smaller) tilt angle than standard monocular or binocular microscope heads

Description of this part for the microscope.

meters:
Manufacturer: Carl Zeiss Jena
Designation: Apl. 1,4
Name of the mount according to the manufacturer's catalogue: Kondensoreinhänger mfl 2, Bestellnummer 301080:021.26/0
Name of the condenser according to the manufacturer's catalogue: Aplanatischer Kondensor 1.4 mo / ms (applies only to the upper optical part)
Name of the condenser according to the manufacturer's catalogue: Kondensor hoher Lichtstärke mit Vorschaltsystem (applies to the entire module)
Version: grey colour with a black upper lens. Variant with a "dot" in the name after "Apl"
Numerical aperture N.A.: 1.4
Aperture diaphragm: yes, attached to the condenser mount
Wide-field lens: yes, it can be swung out of the optical path. This is the version with the large lens in a housing (see description below)
Removable upper lens: yes, it can be rotated
Mounting diameter: the optical part (condenser without diaphragm) has a mounting diameter of 39.5 mm and can be unscrewed from the condenser mount
Operating modes: the condenser can be used both as a dry condenser and as an immersion condenser

The entire part consists of the following elements:
- upper Apl. 1,4 lens
- screw-on/removable condenser (mo / ms)
- iris diaphragm screwed onto the condenser mount
- condenser mount model mfl 2
- swing-out wide-field lens
- two centering screws

This condenser is mainly used in Carl Zeiss Jena Fluoval / Fluoval-2 fluorescence microscopes. It is optimal for use with high-numerical-aperture apochromatic microscope objectives. For precisely this reason, users often install it on Carl Zeiss Jena Ergaval and Carl Zeiss Jena Amplival microscopes equipped with apochromatic objectives (Carl Zeiss Jena Apochromat).

It is worth mentioning again that this condenser can be used in two modes:
- without immersion oil on the upper lens of the condenser. In this case, it operates as a "dry condenser" and its numerical aperture N.A. is 0.9.
- with immersion oil on the upper lens of the condenser (i.e. underneath the microscope slide). In this case, it operates as an "immersion condenser" and its numerical aperture N.A. is 1.4, allowing a very bright image to be obtained - this is important in fluorescence microscopy or when using high-N.A. immersion objectives.

During production, this condenser was available in several versions:
- with a black upper lens, a dot in the model name (Apl. 1,4) and a wide-field module consisting of a single lens
- with a black upper lens, without a dot in the model name (Apl 1,4) and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a wide-field module consisting of two independently swing-out lenses, each on its own mount

I have not found any information anywhere as to whether the above-mentioned versions differ in their operation. From experience, I know that they are used interchangeably - but I do not know whether any differences in operation can actually be noticed.

Mechanically, this condenser is mounted on dovetail rails located underneath the microscope stage. In Carl Zeiss Jena Ergaval microscopes, this is a separate condenser mounting block, whereas in Carl Zeiss Jena Fluoval / Amplival microscopes, the dovetail is located on the microscope stage holder block.

The manufacturer describes this condenser as follows: "High-intensity condenser with an auxiliary system for illuminating large fields while imaging the field diaphragm. [...] The condenser of the FLUOVAL 2 can be used as a dry and immersion condenser of the highest aperture to achieve the highest possible excitation intensity. It is equipped with a switchable wide-field system that illuminates the large fields of low-power objectives while providing a sharp image of the field diaphragm in the object plane."

Description of this part for the microscope.

meters:
Manufacturer: Carl Zeiss Jena
Designation: Apl. 1,4
Name of the mount according to the manufacturer's catalogue: Kondensoreinhänger mfl 2, Bestellnummer 301080:021.26/0
Name of the condenser according to the manufacturer's catalogue: Aplanatischer Kondensor 1.4 mo / ms (applies only to the upper optical part)
Name of the condenser according to the manufacturer's catalogue: Kondensor hoher Lichtstärke mit Vorschaltsystem (applies to the entire module)
Version: grey colour with a black upper lens. Variant without the "dot" in the name after "Apl"
Numerical aperture N.A.: 1.4
Aperture diaphragm: yes, attached to the condenser mount
Wide-field lens: yes, it can be swung out of the optical path. This is the version with the large lens in a housing (see description below)
Removable upper lens: yes, it can be rotated
Mounting diameter: the optical part (condenser without diaphragm) has a mounting diameter of 39.5 mm and can be unscrewed from the condenser mount
Operating modes: the condenser can be used both as a dry condenser and as an immersion condenser

The entire part consists of the following elements:
- upper Apl 1,4 lens
- screw-on/removable condenser (mo / ms)
- iris diaphragm screwed onto the condenser mount
- condenser mount model mfl 2
- swing-out wide-field lens
- two centering screws

This condenser is mainly used in Carl Zeiss Jena Fluoval / Fluoval-2 fluorescence microscopes. It is optimal for use with high-numerical-aperture apochromatic microscope objectives. For precisely this reason, users often install it on Carl Zeiss Jena Ergaval and Carl Zeiss Jena Amplival microscopes equipped with apochromatic objectives (Carl Zeiss Jena Apochromat).

It is worth mentioning again that this condenser can be used in two modes:
- without immersion oil on the upper lens of the condenser. In this case, it operates as a "dry condenser" and its numerical aperture N.A. is 0.9.
- with immersion oil on the upper lens of the condenser (i.e. underneath the microscope slide). In this case, it operates as an "immersion condenser" and its numerical aperture N.A. is 1.4, allowing a very bright image to be obtained - this is important in fluorescence microscopy or when using high-N.A. immersion objectives.

During production, this condenser was available in several versions:
- with a black upper lens, a dot in the model name (Apl. 1,4) and a wide-field module consisting of a single lens
- with a black upper lens, without a dot in the model name (Apl 1,4) and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a wide-field module consisting of two independently swing-out lenses, each on its own mount

I have not found any information anywhere as to whether the above-mentioned versions differ in their operation. From experience, I know that they are used interchangeably - but I do not know whether any differences in operation can actually be noticed.

Mechanically, this condenser is mounted on dovetail rails located underneath the microscope stage. In Carl Zeiss Jena Ergaval microscopes, this is a separate condenser mounting block, whereas in Carl Zeiss Jena Fluoval / Amplival microscopes, the dovetail is located on the microscope stage holder block.

The manufacturer describes this condenser as follows: "High-intensity condenser with an auxiliary system for illuminating large fields while imaging the field diaphragm. [...] The condenser of the FLUOVAL 2 can be used as a dry and immersion condenser of the highest aperture to achieve the highest possible excitation intensity. It is equipped with a switchable wide-field system that illuminates the large fields of low-power objectives while providing a sharp image of the field diaphragm in the object plane."

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Serial number: 039 562 (039562)
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Jena
Inscription: logo "Carl Zeiss Jena" and text "Q1 MADE IN DDR"
Material: aluminium
Length: 52 mm
Width: 14 mm
Mounting: the nameplate is glued on

By default such a nameplate was fitted to most Carl Zeiss Jena microscopes from the Mikroval series onwards. There is also a smaller nameplate - with the manufacturer logo only (without the "Q1 Made in DDR" text). You can see it here: https://www.microscopeparts.eu/part/00604.

Because the adhesive used to attach these plates to the microscope body loses its properties over the years, these plates very often fall off. A nameplate like this makes it possible to restore the factory appearance of a microscope using original parts.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP425
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - because this is an interference filter (it has a mirrored surface), the angle at which the filter sits relative to the incoming light matters and affects its parameters.

The coating on interference filters is sensitive not only to mechanical damage, for example scratches from improper storage or cleaning. Several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP490
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - this is an interference filter, which you can tell from the mirrored surface. For that reason the angle at which the filter sits relative to the incoming light matters and affects its parameters.

The coating on interference filters is sensitive to mechanical damage, for example scratches from improper storage or cleaning. Age is a separate matter - several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP560
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - the mirrored surface gives away that this is an interference filter. With filters of this kind the angle to the incoming light is not indifferent and affects their parameters.

The coating on interference filters is sensitive to mechanical damage, for example scratches from improper storage or cleaning. The second enemy is time - several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B226g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The letter "g" at the end of the designation is short for the German gehärtet, meaning toughened - the manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red passed by that filter and to narrow the excitation band further.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B228g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The "g" at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red that filter passes and to narrow the excitation band further.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B229g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The "g" at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red that filter passes and to narrow the excitation band further.

Description of this part for the microscope.

filter:
Manufacturer: Carl Zeiss Jena
Model: U204g
Filter type: glass excitation filter for UV fluorescence (the manufacturer calls it Erregerfilter)
Glass type: UG 1
Diameter: 32 mm
Thickness: 2 mm
Colour: black-violet, passes very little visible light
Toughened version: yes

The g at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature. With a UV excitation filter this matters especially, because it sits at the hottest point of the whole path and absorbs most of the burner energy.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

The manufacturer catalogue gives the following transmission values for this glass at 2 mm thickness:
- 0.015 at 302 nm
- 0.093 at 312 nm
- 0.435 at 334 nm
- 0.644 at 366 nm

Across the whole visible range, from 405 to 644 nm, transmission is zero. This means the filter works almost entirely on the 366 nm mercury line, exactly where the HBO burner is strongest in the ultraviolet.

One property of this glass is worth knowing: above 700 nm it starts to transmit again, and at 750 nm transmission reaches 0.210. This infrared leak is invisible to the eye, but it heats the specimen and spoils contrast in photographs.

In the excitation path U204 is also combined with a red-absorbing filter. The manufacturer documentation shows such a pair with the B226 filter, which cleans up the excitation band further.

The same UG 1 glass was supplied in two thicknesses, each with its own designation:
- The Carl Zeiss Jena U204 filter is UG 1 glass 2 mm thick
- The Carl Zeiss Jena U205 filter is UG 1 glass 4 mm thick

The thicker U205 cuts more sharply, but passes about a third less energy on the 366 nm line, so the image is noticeably darker.

A safety note: this filter passes ultraviolet, which is invisible and harmful to the eyes. When working with it, never look into the illumination path without a barrier filter in place.