Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

lenses:
- N.A. 0.3 for low-power objectives (this is the lens offered here)
- N.A. up to 1.4 (variable aperture) for high resolution and magnification
- oil dark field lens (cardioid condenser)

This condenser is used in Carl Zeiss Jena microscopes:
- Nf
- Nu / Nu2
- Lumipan
- Amplival (gray condenser)

but can also be mounted in the following microscopes:
- Jenaval
- Jenalumar
- Lu (I'm not sure)
- Ng
- Ergaval
- Docuval
- Polmi A

The companies IOR Bucuresti and Lomo made their own versions of pancratic condensers - I don't know if this lens is compatible with them.

Description of this part for the microscope.

iris diaphragms

Often compatible with microscopes from other manufacturers.

Description of this part for the microscope.

polarizing
- iris diaphragms

Often compatible with microscopes from other manufacturers.

Description of this part for the microscope.

Description of this part for the microscope.

, DIC or polarizing
- iris diaphragms

Often compatible with microscopes from other manufacturers.

Description of this part for the microscope.

Description of this part for the microscope.

came from an EPI-POL illuminator for the Carl Zeiss Jena NU microscope, but as far as I know, the same sliders are compatible with the polarizing kit for the Carl Zeiss Jena Lg, NF, and Polmi-A polarizing microscopes. It's very possible it fits other configurations I'm not aware of, or even microscopes from other manufacturers.

Description of this part for the microscope.

Jena NU microscope, but as far as I know, the same sliders are compatible with the polarizing kit for the Carl Zeiss Jena Lg, NF, and Polmi-A polarizing microscopes. It's very possible it fits other configurations I'm not aware of, or even microscopes from other manufacturers.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

polarized transmitted light with the possibility of use as a brightfield condenser
Mounting: the condenser is permanently integrated with a dovetail mount
Top lens: flip-out system allowing the upper lens to be moved into or out of the optical path to change the numerical aperture
Iris diaphragm: yes
Diffuser: yes, with the possibility of moving it into or out of the optical path
Polarizer: yes, rotatable, with the possibility of moving it into or out of the optical path

This condenser fits the following Carl Zeiss Jena microscope models:
- Polmi-A
- Nf
- Ng
- Nu / Nu2

Note: despite the visual similarity of the mounting interface, this condenser does NOT fit the Carl Zeiss Jena Lu microscope.

Important: the condenser is permanently integrated with the dovetail mount and cannot be used with other microscopes without significant modifications.

Description of this part for the microscope.

, DIC or polarizing
- iris diaphragms

Often compatible with microscopes from other manufacturers.

Description of this part for the microscope.

microscope objective
- Manufacturer: Carl Zeiss Jena
- Designation: Planachromat 25x/0,50 oo/0,17
- Magnification: 25x
- Numerical aperture N.A.: 0,50
- Optical correction: infinity-corrected tube length
- Optical correction class: planachromat
- Cover glass: yes, 0.17 mm
- Thread: M19

Some facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes from this manufacturer:
- these objectives are most commonly used for technical applications rather than biological applications, therefore most objectives available on the secondary market are intended for use without a cover glass (designation oo/0)
- CZJ M19 objectives intended for biological applications (designation oo/0,17) are most commonly used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with an EPI illuminator
- CZJ M19 objectives can be used in Carl Zeiss Jena Polmi-A microscopes, but they provide a different magnification than the nominal value
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes feature interchangeable nosepieces, and a dedicated nosepiece for M19-thread objectives was also produced for these microscopes
- Carl Zeiss Jena Metaval and Neophot microscopes use newer versions of CZJ M19 objectives (with a coarse-knurled edge and shiny housing), although many users still experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various versions with completely different configurations - and some of them operate with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow the use of CZJ M19 objectives in EPI dark-field mode
- on the Carl Zeiss Jena Epityp-2 inverted metallurgical microscope, many users employ biological objectives designed for use with a cover glass, placing the microscope slide "upside down", with the cover glass facing downward toward the objective.

Description of this part for the microscope.

unscrewed. It is mounted onto the dovetail guide located underneath the microscope stage carrier and secured with a clamping screw.

Carl Zeiss Jena Ergaval microscopes were originally equipped with a condenser attached to the "MO" holder. This holder has a permanently mounted iris diaphragm and wide-field lens, while the condenser itself is screwed into the upper thread. In this configuration, the condenser cannot be exchanged.
The Carl Zeiss Jena Fluoval uses a similar arrangement, whereas the Carl Zeiss Jena Amplival was originally equipped with a panchromatic condenser.

If the user wishes to use other condensers (including those made by manufacturers other than Carl Zeiss Jena), the original condenser holder must be replaced with the MZ condenser holder. Once this has been done, any microscope condenser with a mounting diameter of 39.5 mm can be installed. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

This is exactly such a holder for interchangeable condensers.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: grey, the version manufactured for the Mikroval microscope series
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this component is grey, it is also compatible with older black Carl Zeiss Jena microscopes from the 1950s and 1960s (it simply will not look completely original unless it is repainted).

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of condenser holder, making it easy to identify the component.

Description of this part for the microscope.

unscrewed. It is mounted onto a dovetail guide located underneath the microscope stage carrier. The condenser holder is secured to the guide with a clamping screw.

It can accommodate any microscope condenser with a mounting diameter of 39.5 mm, regardless of the manufacturer. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: black, the version manufactured for the black Carl Zeiss Jena microscopes from the 1950s and 1960s
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this microscope component is black, it is also compatible with the newer grey Carl Zeiss Jena microscopes of the Mikroval series.

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of the condenser holder, making it easy to identify the component.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Carl Zeiss Jena
Engraving on the objective: Planachromat 25x/0,50 ∞/0
Magnification: 25x
Numerical aperture N.A.: 0,50
Free working distance: 3,1 mm
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: no - this objective has no phase ring inside
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective calls for eyepieces with additional correction (designated "PK" by Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography by connecting the objective directly to a camera

This objective can be used as:
- an objective for work in reflected light (EPI), for biological as well as, among others, metallurgical or mineralogical applications
- an objective for work in transmitted light, among others with biological specimens or, for example, with mineralogical thin sections

A few facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes of this company:
- these objectives serve mostly technical applications and are intended for work without a cover glass (marking ∞/0)
- CZJ M19 objectives intended for biological applications (that is, marked ∞/0,17) are most often used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with the EPI illuminator and can then work both in bright field and in dark field
- in Carl Zeiss Jena Polmi-A microscopes, CZJ M19 objectives can be used, but they give a magnification other than the nominal one
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes have an interchangeable nosepiece, and there is also a nosepiece intended for these microscopes that accepts objectives with M19 thread
- Carl Zeiss Jena Metaval microscopes use newer versions of CZJ M19 objectives (those with a coarsely knurled rim and a glossy barrel), yet many people experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various configurations - and some work with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow work with CZJ M19 objectives in EPI dark field mode
- on inverted metallographic Carl Zeiss Jena Epityp-2 / Neophot-21 microscopes, many people use biological objectives intended for work with a cover glass alongside metallurgical ones, and place the slide with the specimen on the stage "upside down", that is, with the cover glass facing downwards

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 25x/0,50 ∞/0 Ph
Magnification: 25x
Numerical aperture N.A.: 0,50
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) is the same objective in the version without phase rings. Its description tells you more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 12.5x/0.25 ∞/0 Ph
Magnification: 12.5x
Numerical aperture N.A.: 0.25
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) you can read more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 6.3x/0.12 ∞/0 Ph
Magnification: 6.3x
Numerical aperture N.A.: 0.12
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) you can read more about using Carl Zeiss Jena objectives with an M19 thread.