Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

part of the housing. Screws are included. The set includes an ON/OFF switch for mounting in the housing. The set DOES NOT include a light intensity regulator. There is also a plug for the illuminator cable on the back of the housing. The illuminator cable itself is not included.

So-called transformer, "electrics", electric circuit, electronic board.

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Basic data:
- Element: microscope condenser
- Manufacturer: Meopta
- Manufacturer part number: 573 08 (57308)
- Numerical aperture: 1.0
- Design: condenser with a double-lens optical system
- Mounting diameter: 37 mm (exactly according to the manufacturer catalog 36.8 mm)
- Iris diaphragm: YES

Note - although the manufacturer describes it as "for polarizing microscopes" - this is NOT a polarizing condenser, i.e. it does not contain a polarizer - neither fixed nor rotatable.

This condenser fits any Meopta microscope as well as microscopes from other manufacturers (e.g. Lomo, Olympus, Carl Zeiss Jena and many others) with a condenser holder diameter of 37 mm.

Description of this part for the microscope.

08 160/-
Color correction: Planachromat
Numerical aperture: 0.08
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

Description of this part for the microscope.

Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: no
Thread: RMS
Info: Ph = phase contrast

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

mm
Focal Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: Ph3 = phase contrast

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

microscope from any manufacturer that allows the use of eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

10x
Correction: Achromat
Numerical aperture: 0.24
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS
Info: PI = polarization-interference objective (red ring).

Compatible with the following PZO condensers:
- PZO KPI 2
- slit condenser
PI objectives are among the components of the PZO UPI set (i.e. the so-called DIC).

VERY IMPORTANT: the marking on the objective is "PI" (in lowercase: "pi"), meaning [P]-polarization [I]-interference.
In many descriptions available on the Internet, you can find information that this is a PLAN objective. This is an ERROR caused by misinterpreting the marking as PL.

Note: another INCORRECT piece of information often found online is that these are DIC objectives. This is not true.
DIC according to Pluta (niem: DIC nach Pluta), sold by PZO, achieves the DIC effect (i.e. a 3D relief image) using standard achromatic PZO objectives (and not only those). Objectives marked PI with a red ring are not required for this.

It can be used with any microscope from any manufacturer that supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

On the condenser, the model name is written in Cyrillic and looks similar to ON-14.

The Lomo OI-14 condenser has a removable (unscrewable) top lens:
- A1.4 with high aperture, for use with objectives with high numerical aperture (which corresponds to high magnifications, it can be assumed above 40x)
- A0.3 with low aperture, for use with low magnification objectives

Although it is possible to work with low magnification objectives (e.g. 5x or 10x) using a condenser with the A1.4 lens installed - the image is too "sharp" and contrasty. In this case, replacing the lens with A0.3 allows obtaining a pastel, soft and visually pleasant image.

Since the Lomo OI-14 condenser has been produced since the 1960s, over the years this additional lens has very often been lost and most condensers available on the secondary market have only one - most often A1.4.

The Lomo OI-14 condenser has a mounting diameter of 37 mm, but since it is very popular among microscope users, an extension ring is often used, allowing it to be mounted in microscopes with a 39.5 mm condenser holder. This condenser fits microscopes from various manufacturers: Lomo, PZO, Zeiss, Carl Zeiss Jena, Meopta, IOR, Olympus, ROW, Nikon, Leitz Wetzlar and many others.

Description of this part for the microscope.

10 160/-
Color correction: Planachromat
Numerical aperture: 0.10
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Color correction: Planachromat
Numerical aperture: 0.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.32
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 1,25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: HI = Homogene Immersion, also oil immersion

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

eyepieces can be used with microscopes from any manufacturer, as long as the microscope supports eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

microscopes from any manufacturer, as long as the microscope supports eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

for taking microscope photographs or recording microscope videos. This is a gray photographic adapter.

Basic technical parameters:
- mounting connection to microscope stand: 41 mm dovetail
- output connection type on the photo port: 49 mm internal thread
- connection for binocular head mounting: Jena standard 41 mm dovetail
- magnification directed to the binocular head: 1.6x
- magnification on the photo output: none (that is 1.0x)

Because this photo head has a 49 mm threaded output, virtually any device, camera, adapter, tube or other accessory can be connected after using an appropriate 49 mm thread adapter. Direct projection technique may be used (because there is no additional optics inside), or any projection eyepieces may be installed in the optical path.

This photographic attachment is intended mainly (but not exclusively) for the following microscope models:
- Carl Zeiss Jena Eduval
- Carl Zeiss Jena Laboval
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Telaval
- Carl Zeiss Jena Pictoval
- Carl Zeiss Jena Epignost

The list above contains Mikroval series microscopes with gray housings - just like the tube shown and offered here. However, it also works with older black Carl Zeiss Jena microscopes:
- Carl Zeiss Jena L-Stativ (models Lg, Lu and Lr)
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Ng
- Carl Zeiss Jena Nf (and NfPk)

Please note that microscopes from other manufacturers also use the 41 / 41.5 mm dovetail connection standard. Because of this, this photographic head can also be used with microscopes made by:
- Lomo (for example Lomo Biolam)
- Meopta
- IOR
- selected Reichert microscopes (for example Reichert Neozet)
- Will Wetzlar
- Hund Wetzlar
- Leitz Wetzlar

This Carl Zeiss Jena tube is also very often used with microscopes having a larger head mounting diameter. In such cases users apply additional spacer or thickening rings. Because of this, this photo adapter also fits microscopes from manufacturers such as:
- PZO (for example the PZO Biolar model with 43 mm connection)
- Olympus (for example the Olympus CH model with 42 mm connection)

The element that allows a photographic camera or imaging camera to be connected to Carl Zeiss Jena Mikroval series microscopes may be referred to by different names. Commonly used names include:
- trino head
- trinocular head
- photo head
- photographic head
- photo attachment
- photographic attachment
- photo adapter
- photographic adapter
- photo tube
- photographic tube
- phototube
- photographic angle tube
- and various combinations of the words head, attachment, adapter or tube with terms such as photo, photographic, for camera and similar

Description of this part for the microscope.

diffuser)
- blue
- yellow
- green

New (usually Chinese) microscope filters are sometimes not even made of glass. And even if they are made of glass - you may encounter scandalous examples where the glass is only surface-colored. Unfortunately, cheap colored glass filters may not be internally homogeneous and can cause light refraction distortions.

This filter set by PZO was originally sold together with the PZO Biolar microscope. It was manufactured in the 1970s (and certainly before 1977), so these are optical glasses that are about half a century old! They have never been used until now (this is so-called NOS - New Old Stock), therefore these are excellent old-class optical glasses of the highest quality.

Filters with a 32 mm diameter are used - and can be used - in microscopes from various manufacturers:
- Carl Zeiss Jena
- Zeiss West Germany
- Eschenbach
- Meopta
- Nikon
- ROW
- Leitz Wetzlar
- Wild
- Hund
- Kosmos
- and many others

Important - popular microscopes by Lomo (for example Lomo Biolam) have a 33 mm filter holder, so the filters shown here have too small a diameter and may fall out from some Lomo holders.

Description of this part for the microscope.

magnification is very often used as a projection eyepiece for microphotography.

This eyepiece works with any microscope from any manufacturer that allows the use of eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

any microscope from any manufacturer that allows the use of eyepieces with a mounting diameter of 23.2 mm.

The company "Dr. G. Schuchardt Göttingen" did not and does not produce microscopes. Previously, it primarily sold microscopes manufactured by Hertel & Reuss and Will Wetzlar under its own brand.

Description of this part for the microscope.

35 160/0.17
Manufacturer part number: 46 05 10-9906 (alternative notation: 460510 - 9906)
Color correction: Planachromat
Numerical aperture N.A.: 0.35
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm thickness
Immersion: no (dry objective)
Thread: RMS

Description of this part for the microscope.

65 160/0.17
Manufacturer part number: 46 07 10-9904 (alternative notation: 460710 - 9904)
Color correction: Planachromat
Numerical aperture N.A.: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm thickness
Immersion: no (dry objective)
Thread: RMS

Description of this part for the microscope.

Carl Zeiss Jena, PZO, Meopta, Olympus, IOR and others.

This tube makes it possible to connect a camera or photographic camera to a trinocular head or directly to the microscope body, even when no trinocular head is installed.

Originally, this adapter was designed for the Lomo TRN-1 trinocular head. This head was used in Lomo Polam polarizing microscopes from the early 1970s onwards.

Several remarks regarding the model designation of the trinocular head for which this component was originally intended:
- the name Lomo TRN-1 is the Latin alphabet designation. In Cyrillic script the model designation appears as TPH (for example model TPH1Y4.2), and this designation is used in the manual for the Lomo Polam L-211 microscope
- the vast majority of these trinocular heads are not marked with any model designation
- the Envirotools website http://www.envirotools.hu/ateso_fenyu_polarizacios_mikroszkop.htm refers to this trinocular head as HU-POL

In the last photograph, an arrow indicates exactly which component is being offered and where it is located in the Lomo Polam microscope, allowing this part to be identified unambiguously.

Basic technical parameters of this tube:
Mounting method to the trinocular head or microscope: 41 mm dovetail mount (this is also the Carl Zeiss Jena standard)
Camera mounting method: male M39 thread
Alternative camera mounting method: since the M39 thread can be removed, a plain smooth tube with a diameter of 35 mm remains
Additional optics: yes, the original optics are installed inside, although they can be removed, leaving only an "empty tube".

This is not "a tube dedicated to a specific microscope model". It is a tube originally mounted on the third port (photo port) of a trinocular head. Since a trinocular head can be installed on microscopes other than the model with which it was originally supplied, this tube can be regarded as a universal accessory.

These technical parameters make it possible to use this tube with virtually any microscope manufactured by:
- Lomo (for example Biolam, Polam, MBB-1A and others)
- Carl Zeiss Jena (for example Ergaval, Amplival, Jenamed and others)
- IOR, Meopta and other manufacturers using a 41 / 41.5 mm dovetail mount

In addition, a 41 mm dovetail tube can easily be mounted on microscopes equipped with a 42 mm or 43 mm opening, for example:
- Olympus (for example CH, CH-2, BH-2 models)
- PZO (for example Biolar, Studar, MB-30 and others)

The entire list of microscope manufacturers and models given above may also be treated as a list of microscopes compatible with the Lomo TRN-1 trinocular head. Indeed, many examples can be found on the Internet showing this head being used with microscopes made by manufacturers other than Lomo.

Because this tube is equipped with an M39 thread by default, almost any camera or photographic camera can be attached by means of a suitable adapter, for example:
- devices with M42 threads
- devices with C-mount threads
- Nikon, Sony, Olympus and other camera standards

This is therefore a universal photo tube featuring a 41 mm dovetail on one side and either an M39 thread or a 35 mm tube on the other side.

In the image gallery, every photograph includes a millimetre scale, and in addition, the dimensions of the dovetail, tube and thread have been measured with calipers so that compatibility can be determined precisely.

Description of this part for the microscope.

Wetzlar
Model: 160/0,17 EF 100/1.25 OEL PHACO 3
Magnification: 100x
Correction: semi-plan achromat
Numerical aperture: 1.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm
Immersion: yes, oil
Thread: RMS
Specimen protection: yes - spring-loaded
Info: PHACO 3 = phase contrast

Some important information about this objective:
- the designation "EF" means "Extended Field" - this is a semi-plan achromatic objective with an 18 mm field of view, which should be taken into account when selecting suitable eyepieces
- the semi-plan achromatic correction is "almost flat" - it is no longer an achromat, but not yet a plan achromat
- this objective can be used in brightfield, but phase contrast operation requires a compatible phase contrast condenser or a slide (slider) with a phase ring diaphragm
- the designation PHACO 3 means that for phase contrast operation a phase contrast condenser set to ring "3" should be used (the equivalent setting used by Zeiss is called "Ph3")
- this objective can be used with microscopes designed for objectives with a 170 mm tube length, but in such a case the optical path must be extended by 10 mm - most commonly by pulling the eyepieces out of the tubes by 10 mm

This objective can be used with any microscope from any manufacturer together with a compatible phase contrast condenser. Naturally, the microscope must be compatible, i.e. it must support RMS objectives, TL=160 mm and FL=45 mm - or have adapters that make such adaptation possible (for example thread adapters).

Description of this part for the microscope.

ameters:
Manufacturer: Lomo
Model: PLAN 25x0.50 P
Original designation: ЛОМО ПЛАН 25х0,50 П
Magnification: 25x
Numerical aperture N.A.: 0.50
Tube length: 160 mm
Cover glass: yes, 0.17 mm thickness
Immersion oil: no - this is a dry objective
Focal length: 45 mm
Thread type: RMS
Additional designation: P (Cyrillic: П) indicates that this objective is designed for use with polarized light
Special features: built-in iris diaphragm
Year of manufacture: 1976

This objective has a standard RMS thread and TL=160 mm, which means it can be used with the vast majority of microscopes from virtually any manufacturer, including Olympus, Zeiss, Nikon, PZO, Carl Zeiss Jena, Reichert, Wild and many others.

The built-in iris diaphragm allows, among other things, precise centering of the objective, because in a polarizing microscope the following diaphragms may operate simultaneously:
- field diaphragm in the illuminator
- aperture diaphragm (or two aperture diaphragms) in the condenser
- iris diaphragm in the microscope objective
- iris diaphragm in the eyepiece head
and accurate centering of all of them relative to each other is very important in polarized-light observations.

Objectives marked "P" / "Pol" feature a special construction in which the lenses are mounted and cemented in a way that prevents mechanical stress. They can be used both for conventional brightfield microscopy and for observations in polarized light.

Description of this part for the microscope.

screw was removed from a Olympus CH microscope, but it will most likely fit most models of the CH series, for example:
- Olympus CHK
- Olympus CHB
- Olympus CK2
- Olympus CH
- Olympus CH-2

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Serial number: 039 562 (039562)
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

2 mm

Because this is important, I will write it again: this is a single eyepiece, not a pair of eyepieces.

This is a solution for people who:
- either have a pair of these eyepieces, but one of them needs to be replaced
- or have a microscope with a monocular head

For Will Wetzlar microscopes, eyepieces from practically any manufacturer can be used, provided that they are designed for a finite tube length system and have a mounting diameter of 23.2 mm. However, many users appreciate having original parts.

This eyepiece also works the other way around - it fits almost any microscope from any manufacturer that allows the use of eyepieces with a mounting diameter of 23.2 mm. Users of microscopes from many manufacturers are happy to choose German eyepieces because of their high quality. I have included some examples in the "compatibility" section, but this is definitely not a complete list.

Description of this part for the microscope.

2 mm

Because this is important, I will write it again: this is a single eyepiece, not a pair of eyepieces.

This is a solution for people who:
- either have a pair of these eyepieces, but one of them needs to be replaced
- or have a microscope with a monocular head

For Will Wetzlar microscopes, eyepieces from practically any manufacturer can be used, provided that they are designed for a finite tube length system and have a mounting diameter of 23.2 mm. However, many users appreciate having original parts.

This eyepiece also works the other way around - it fits almost any microscope from any manufacturer that allows the use of eyepieces with a mounting diameter of 23.2 mm. Users of microscopes from many manufacturers are happy to choose German eyepieces because of their high quality. I have included some examples in the "compatibility" section, but this is definitely not a complete list.

Description of this part for the microscope.

for inverted and upright biological microscopes, made in Japan.

Basic objective parameters:
Manufacturer: Nikon, Japan
Model: Ph3 40 DL 0.55 LWD 160/0-2
Magnification: 40x
Numerical aperture (N.A.): 0.55
Optical correction: achromat
Phase contrast: Ph3 DL - Ph3 indicates the size of the phase ring (requires a matching Ph3 annulus in the condenser), DL (Dark Low) means dark, i.e. positive phase contrast - the object appears darker than the background
Working distance (WD): ~2.1 - 2.5 mm - LWD (Long Working Distance)
Correction collar: compensates for cover glass or vessel bottom thickness in the range 0 - 2.0 mm
Cover glass: the objective can be used without a cover glass, with a standard cover glass approx. 0.17 mm thick, and also with specimens observed through the bottom of a Petri dish up to 2.0 mm thick
Immersion: no (dry objective)
Tube length: 160 mm
Parfocal length: 45 mm
Thread: RMS
Optics: CF (Nikon CF-160) - requires no compensating eyepiece and allows photography by direct projection

This objective is suitable for:
- inverted microscopes - observation through the bottom of a Petri dish or cell culture flask
- upright biological microscopes - observation of specimens with or without a cover glass

Phase contrast work requires a compatible phase contrast condenser or a slider with a phase contrast annulus.

Commonly used, inexpensive cover glasses are 0.17 mm thick mainly in theory. Even the standard for class #1.5 allows a range of 0.16 - 0.19 mm, and in cheap Chinese cover glasses you will find in practice pieces from approx. 0.13 to 0.25 mm, often not matching the thickness stated on the box. Only #1.5H (high precision) cover glasses have a guaranteed thickness of 0.170 mm with a tolerance of +/- 0.005 mm. Variation in cover glass thickness clearly degrades image contrast and resolution (spherical aberration). The correction collar fitted to the objective offered here lets you adjust the optics to the combined thickness of the cover glass and the medium layer beneath it. This compensates for most of the variation found in practice.

In addition, the correction collar of this objective can be set to "0" for work without a cover glass, or to large values (up to 2.0 mm) to adapt the optics to observation through a microscope slide (0.8 - 1.2 mm), a glass Petri dish (usually 1.5 - 2.0 mm - thicker dishes are outside the collar range) or a plastic Petri dish (usually approx. 1 mm, in the range 0.8 - 1.2 mm).

This objective fits practically any microscope from any manufacturer, provided it has an RMS thread and uses objectives for 160 mm tube length with a parfocal length of 33, 37 or 45 mm. Some example microscopes are listed in the "compatibility" section, but the list is not complete.