Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

objective nosepiece and the microscope arm. In the Carl Zeiss Jena Jenalumar microscope, a fluorescence filter cube slides into position above the objective revolver. Inside this holder there is a longitudinal dovetail guide along which the fluorescence filter cubes slide. It also contains a spring steel detent that provides a distinct "click" to indicate the filter position as the fluorescence filter cube is moved along the dovetail guide.

The objective revolver is attached to this holder with screws, and the complete assembly consisting of the holder and objective turret is then screwed to the microscope arm.

The complete objective nosepiece module for Carl Zeiss Jena Jenalumar or Jenaval microscopes consists of:
- the objective revolver (also called the objective nosepiece, nosepiece disc or objective turret)
- the intermediate mounting bracket (nosepiece holder).

In both microscope models, the Carl Zeiss Jena Jenalumar and the Carl Zeiss Jena Jenaval, the first component - the objective revolver - is identical and interchangeable between the two models. Only the intermediate mounting bracket differs, as it attaches the revolver to the microscope arm. In other words, the nosepiece holder used in the Carl Zeiss Jena Jenalumar microscope is different from the one used in the Carl Zeiss Jena Jenaval microscope, but both holders have exactly the same objective revolvers attached to them.

This listing includes only the intermediate holder for the Carl Zeiss Jena Jenalumar model, without the objective nosepiece.

Interestingly, this component is made of aluminium, whereas the corresponding component performing the same function in the Carl Zeiss Jena Jenaval microscope is manufactured from a ZnAl alloy. Cast or injection-moulded ZnAl components made by Carl Zeiss Jena carry identification numbers that allow them to be identified. In the Jenaval microscope this number is 2643 (full marking: Si10 CZ 2643). The objective nosepiece holder used in the Jenalumar does not carry such a number.

Another useful piece of information is that the sliding fluorescence filter cube from the Carl Zeiss Jena Jenamed Fluorescence microscope fits the dovetail guide incorporated into this nosepiece holder.

The gallery includes photographs of the complete assembly consisting of the objective nosepiece and its holder for the Jenalumar microscope, making it clear how these two components are connected.

This database also contains, under item number 99678, the separate objective revolver without the holder.

Description of this part for the microscope.

The complete set presented here consists of three components:
1. a small metal plate marked with the numbers 1 to 8 - these identify the terminal positions
2. an electrical tab terminal strip with eight terminals, housed in a plastic body
3. the rear sheet-metal cover of the microscope arm with the printed 6V illumination wiring diagram

This set was removed from a Carl Zeiss Jena Jenalumar microscope.

Components "1" and "2" (the numbered plate and the electrical tab terminal strip) are universal and fit the following microscope models:
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenavert
- Carl Zeiss Jena Jenapol

Component "3" (the rear sheet-metal cover of the microscope arm)
- fits the Carl Zeiss Jena Jenalumar microscope
- does not fit the Carl Zeiss Jena Jenaval microscope
- I do not know whether it fits the Carl Zeiss Jena Jenavert or Jenapol microscopes, as I have not personally tested this.

The 6V supply wires coming from the power supply are connected to the input terminals on the underside of this electrical tab terminal strip. The power supply is built into the microscope base. The lampenhaus fitted with a 6V 25W halogen bulb is connected to the output terminals on the upper side. In the Carl Zeiss Jena Jenaval and Jenalumar microscopes this supplies the transmitted-light illuminator. In the Carl Zeiss Jena Jenavert microscope it supplies the reflected-light illuminator.

In microscope versions equipped with two illuminators, only one of them can be powered from the power supply built into the microscope base, because the built-in power supply has a maximum output power of 25 W. The second illuminator requires an external power supply appropriate for the particular light source (a halogen lamp, a fluorescence light source, or - in the case of LED illuminators - an LED power supply with a dimmer).

This database also contains, under item number 99694, the same component together with the rear sheet-metal cover of the microscope arm from a Carl Zeiss Jena Jenaval microscope. You can compare the two versions to see the difference in the size of the rear sheet-metal cover between the Carl Zeiss Jena Jenaval and Jenalumar models.

If you need only one component from this set - either the rear microscope arm cover or only the electrical tab terminal strip - please contact us by email or through social media.

Description of this part for the microscope.

objective nosepiece and the microscope arm of the Carl Zeiss Jena Jenaval microscope.

The complete assembly (objective revolver ↔ holder ↔ microscope arm) is connected together with screws.

The complete objective nosepiece module for Carl Zeiss Jena Jenalumar or Jenaval microscopes consists of:
- the objective revolver (also called the objective nosepiece, nosepiece disc or objective turret)
- the intermediate mounting bracket (nosepiece holder).

In both microscope models, the Carl Zeiss Jena Jenalumar and the Carl Zeiss Jena Jenaval, the first component - the objective revolver - is identical and interchangeable between the two models. Only the intermediate mounting bracket differs, as it attaches the revolver to the microscope arm. In other words, the nosepiece holder used in the Carl Zeiss Jena Jenaval microscope is different from the one used in the Carl Zeiss Jena Jenalumar microscope, but both holders have exactly the same objective revolvers attached to them.

This listing includes only the intermediate holder for the Carl Zeiss Jena Jenaval model, without the objective nosepiece.

Cast or injection-moulded ZnAl components manufactured by Carl Zeiss Jena carry identification numbers that allow them to be identified. This component bears the number 2643 (full marking: Si10 CZ 2643).

This database also contains:
- under item number 99678 the separate objective revolver without the holder
- under item number 99682 the separate objective nosepiece holder for the Carl Zeiss Jena Jenalumar microscope
- under item number 99388 the complete objective nosepiece with holder for the Carl Zeiss Jena Jenaval model

Description of this part for the microscope.

It is not an illuminator holder in the literal sense. The illuminator is secured with screws to the sides of the microscope's vertical arm. Instead, the central circular opening in this component is designed to receive and accurately position the cylindrical light-output section of the illuminator (lamphouse).

Microscopes designed for reflected-light operation (either exclusively or in addition to transmitted light), such as the Carl Zeiss Jena Jenalumar, Jenavert and Jenapol-U, have a different upper horizontal microscope arm from models intended exclusively for transmitted light, such as the Carl Zeiss Jena Jenaval. The reflected-light arm includes a slot for filter sliders, a slot for an aperture slider and, of course, an angled mirror.

Interestingly, this component is also present in Carl Zeiss Jena Jenaval microscopes, even though the standard version of this model is not equipped with an EPI reflected-light illuminator. Since it is not used there, it is normally covered by the rear sheet-metal cover of the microscope arm. This is exactly why the rear cover of the Carl Zeiss Jena Jenalumar microscope is shorter than that of the Jenaval model - it does not have to cover this component (see item no. 99679 in this database).

This component fits the following microscope models:
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenavert
- Carl Zeiss Jena Jenapol

- in the Carl Zeiss Jena Jenaval microscope this component is hidden behind the rear sheet-metal cover and is not used
- in the Carl Zeiss Jena Jenalumar 50 this component receives the small 50W HBO fluorescence illuminator
- in the Carl Zeiss Jena Jenalumar 250 with the large integrated lamphouse, this component receives the light-output section of the 250W HBO fluorescence illuminator
- in the Carl Zeiss Jena Jenavert this component receives the 50W/100W halogen illuminator
- Carl Zeiss Jena Jenapol microscopes may be equipped with various EPI reflected-light illuminators

Cast or injection-moulded ZnAl components manufactured by Carl Zeiss Jena carry identification numbers that allow them to be identified. This component bears the number 2650 (full marking: Si10 2650).

Description of this part for the microscope.

Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

The function of this microscope component is to reflect the light coming from the microscope base vertically upwards so that, after passing through the microscope slide with the specimen and the objective, it reaches the eyepieces and finally the user's eyes.

This component is a metal casting with a circular opening. The mirror is mounted in this opening. The complete assembly is fastened to the microscope base with screws.

Metal cast or injection-moulded microscope components manufactured by Carl Zeiss Jena carry identification numbers. The part to which the mirror is attached bears the number 2649 (full marking: Si10 CZ 2649).

Replacement of the right-angle mirror in Carl Zeiss Jena microscopes may be necessary in the following situations:
- if the mirror has become significantly scratched due to improper cleaning (minor scratches are usually not visible during normal use)
- if the reflective silver coating of the installed mirror has become oxidised
- if the mirror has been damaged, chipped or cracked, for example after becoming detached from its mount
- if the metal casting holding the mirror chips or breaks due to age, stresses caused by the mounting screw or mechanical damage

Description of this part for the microscope.

The complete set presented here consists of three components:
1. a small metal plate marked with the numbers 1 to 8 - these identify the terminal positions
2. an electrical tab terminal strip with eight terminals, housed in a plastic body
3. the rear sheet-metal cover of the microscope arm with the printed 6V illumination wiring diagram

This set was removed from a Carl Zeiss Jena Jenaval microscope.

Components "1" and "2" (the numbered plate and the electrical tab terminal strip) are universal and fit the following microscope models:
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenavert
- Carl Zeiss Jena Jenapol

Component "3" (the rear sheet-metal cover of the microscope arm)
- fits the Carl Zeiss Jena Jenaval microscope
- does not fit the Carl Zeiss Jena Jenalumar microscope
- I do not know whether it fits the Carl Zeiss Jena Jenavert or Jenapol microscopes, as I have not personally tested this.

The 6V supply wires coming from the power supply are connected to the input terminals on the underside of this electrical tab terminal strip. The power supply is built into the microscope base. The lampenhaus fitted with a 6V 25W halogen bulb is connected to the output terminals on the upper side. In the Carl Zeiss Jena Jenaval and Jenalumar microscopes this supplies the transmitted-light illuminator.

In microscope versions equipped with two illuminators, only one of them can be powered from the power supply built into the microscope base, because the built-in power supply has a maximum output power of 25 W. The second illuminator requires an external power supply appropriate for the particular light source (a halogen lamp, a fluorescence light source, or - in the case of LED illuminators - an LED power supply with a dimmer).

This database also contains, under item number 99679, the same component together with the rear sheet-metal cover of the microscope arm from a Carl Zeiss Jena Jenalumar microscope. You can compare the two versions to see the difference in the size of the rear sheet-metal cover between the Carl Zeiss Jena Jenaval and Jenalumar models.

If you need only one component from this set - either the rear microscope arm cover or only the electrical tab terminal strip - please contact us by email or through social media.

Description of this part for the microscope.

Jenapol
- Carl Zeiss Jena Jenalumar

This cover serves two main functions in the microscope:
- it protects the power supply and all electrical components built into the microscope base, protecting both the electrical system and the user from electric shock
- it protects the optical components located inside the microscope base from dust and other contamination

The base of Carl Zeiss Jena Jenaval, Jenalumar and similar microscopes contains part of the optical light path, and this area occasionally requires maintenance, especially cleaning. Since these microscopes are now more than 30 years old, it is not uncommon to find examples with this cover missing because it has been lost over the years.

Description of this part for the microscope.

Jena microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- can also be installed in a Carl Zeiss Jena Jenavert microscope to add transmitted-light capability

This component is located inside the microscope base. It receives the light beam from the illuminator, homogenises it (by diffusing the image of the lamp filament using a frosted filter acting as a diffuser) and then properly collimates it using a collimating lens. The prepared light beam then passes through another lens before reaching the right-angle mirror (sold as a separate component).

This part is well known on the secondary market among hobbyists and engineers building their own DIY optical projects, where it is frequently reused.

Interestingly, microscope versions intended exclusively for reflected-light operation (for example, the basic versions of the Carl Zeiss Jena Jenavert) do not contain this component because they do not have a transmitted-light optical path. However, both the microscope arm and the microscope base are identical to those used in transmitted-light models. This makes it possible to upgrade such an EPI microscope for transmitted-light operation by installing the complete lower transmitted-light optical path. The component offered here is one of the parts required for this conversion.

In the last photograph, an arrow indicates where this component is located inside the microscope, making it easy to identify.

Description of this part for the microscope.

Jena microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

This component serves almost exclusively a cosmetic purpose. At both the top and bottom of the sheet-metal cover there are openings through which the long screws pass. These screws secure the transmitted-light lamp housing to the rear of the microscope body (at the bottom) or the reflected-light EPI lamp housing (at the top).

Each microscope has two of these sheet-metal covers - one on the left side and one on the right. Both are identical, so there is no difference between the left-hand and right-hand cover.

The cover is attached using ordinary adhesive and, after many years, it may simply come loose and fall off. These covers are also sometimes lost during repairs or maintenance, so older microscopes are often missing them. Reattaching an original cover is an easy way to restore the microscope to its original appearance.

In the last photograph, an arrow indicates where this component is located on the microscope, making it easy to identify.

Description of this part for the microscope.

models:
1. Carl Zeiss Jena Jenaval
2. Carl Zeiss Jena Jenalumar
3. Carl Zeiss Jena Jenapol
4. Carl Zeiss Jena Jenavert

1. In Carl Zeiss Jena Jenaval microscopes, this lamp house is used as the transmitted-light illuminator.

2a. In Carl Zeiss Jena Jenalumar 50 microscopes (equipped with the small HBO 50 fluorescent lamp house, identical to the one used in Carl Zeiss Jena Jenamed Fluorescence microscopes), this lamp house serves as the transmitted-light source.

2b. Carl Zeiss Jena Jenalumar 250 microscopes are equipped with a large integrated lamp house. The unit offered here is therefore not compatible with this model.

3. In Carl Zeiss Jena Jenapol microscopes, this halogen lamp house is used both for transmitted light (mounted underneath) and for reflected light (mounted on the top). However, some Jenapol versions are equipped only for transmitted-light operation or only for reflected-light operation.

4. Carl Zeiss Jena Jenavert microscopes are normally equipped with a different lamp housing for reflected light. However, when the original unit is missing, users often modify a lamp house like the one offered here for DIY projects. In addition, if a Jenavert is equipped with a transmitted-light optical path, this lamp house is used as its transmitted-light source.

The lamp house is attached to the microscope using two long screws. Unusually - and this often makes them difficult to find - the screws are removed FROM THE FRONT of the microscope. Their heads are accessible through openings in the white sheet-metal side covers of the microscope body. These covers with the screw openings are shown in this database under item number 99692.

This lamp house contains a filter wheel with four positions for 32 mm diameter round filters. It is fitted with the same filter configuration originally supplied by Carl Zeiss Jena for the Jenaval model:
- one position is empty
- Carl Zeiss Jena C312 blue filter
- Carl Zeiss Jena D282 grey filter
- Carl Zeiss Jena V231 green filter

The filter wheel is an optional part of this lamp house. The example offered here is fitted with it, but it can be removed and the illuminator will still function perfectly as a light source.

Cast or injection-moulded ZnAl components manufactured by Carl Zeiss Jena carry identification numbers. The housing of this lamp house bears the number 2670 (full marking: 2670 Si10 CZ).

In the last photograph, an arrow indicates where this component is located in the microscope, making it easy to identify.

Description of this part for the microscope.

transformer assembly installed inside the microscope base. It converts an input voltage of 110-240 V into a 6 V output with a maximum power of 25 W. It is intended to power a halogen lamp house. An example of this lamp house can be found in this database under item number 99693.

This is not the power supply for the 50W/100W reflected-light lamp housing used on the Carl Zeiss Jena Jenavert. It is also not the power supply for the fluorescent lamp houses used on the Carl Zeiss Jena Jenalumar.

Compatible with the following microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

If you only need one component from this assembly - for example the transformer, one of the electronic circuit boards or just the potentiometer used to adjust the lamp brightness - please contact us by email or through our social media channels.

This complete assembly may be useful for solving the following microscope problems, among others:
- if the microscope illumination no longer works because of a faulty power supply. This may be caused by mains voltage surges, ageing electronic components or damage resulting from incorrect modifications (for example, conversion to LED lighting)
- if the illumination works but the brightness can no longer be adjusted because the potentiometer is worn out or defective

Originally, the complete power supply assembly (transformer, electronic circuit boards and wiring) is installed inside the microscope base, and it is offered here exactly in that configuration. How can it be used?
- the electrical components can be removed and used as spare parts to repair a damaged power supply
- the complete microscope base can be transplanted to another microscope (please note that it does not include any optical components)

An interesting DIY modification is to leave the power supply in the base offered here and then place the microscope on top of that base. This effectively raises the microscope while also providing an integrated power supply for a second lamp house.

Description of this part for the microscope.

microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- can also be installed in a Carl Zeiss Jena Jenavert microscope to add transmitted-light capability

This component is located inside the microscope base and enables the microscope illumination to be adjusted according to the Köhler illumination principle.

Interestingly, microscope versions intended exclusively for reflected-light operation (for example, the basic versions of the Carl Zeiss Jena Jenavert) do not include this transmitted-light field diaphragm because they do not have a transmitted-light optical path. However, the microscope base is identical to that used in transmitted-light models. This makes it possible to upgrade such an EPI microscope for transmitted-light operation by installing the complete lower transmitted-light optical path. The field diaphragm offered here is one of the components required for this conversion.

In the last photograph, an arrow indicates where the transmitted-light field diaphragm is located inside the microscope base, making this component easy to identify.

Description of this part for the microscope.

unscrewed. It is mounted onto the dovetail guide located underneath the microscope stage carrier and secured with a clamping screw.

Carl Zeiss Jena Ergaval microscopes were originally equipped with a condenser attached to the "MO" holder. This holder has a permanently mounted iris diaphragm and wide-field lens, while the condenser itself is screwed into the upper thread. In this configuration, the condenser cannot be exchanged.
The Carl Zeiss Jena Fluoval uses a similar arrangement, whereas the Carl Zeiss Jena Amplival was originally equipped with a panchromatic condenser.

If the user wishes to use other condensers (including those made by manufacturers other than Carl Zeiss Jena), the original condenser holder must be replaced with the MZ condenser holder. Once this has been done, any microscope condenser with a mounting diameter of 39.5 mm can be installed. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

This is exactly such a holder for interchangeable condensers.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: grey, the version manufactured for the Mikroval microscope series
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this component is grey, it is also compatible with older black Carl Zeiss Jena microscopes from the 1950s and 1960s (it simply will not look completely original unless it is repainted).

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of condenser holder, making it easy to identify the component.

Description of this part for the microscope.

unscrewed. It is mounted onto a dovetail guide located underneath the microscope stage carrier. The condenser holder is secured to the guide with a clamping screw.

It can accommodate any microscope condenser with a mounting diameter of 39.5 mm, regardless of the manufacturer. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: black, the version manufactured for the black Carl Zeiss Jena microscopes from the 1950s and 1960s
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this microscope component is black, it is also compatible with the newer grey Carl Zeiss Jena microscopes of the Mikroval series.

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of the condenser holder, making it easy to identify the component.

Description of this part for the microscope.

reflector, performs two functions:
- it contains a barrier filter (emission filter) for the 450 nm wavelength
- it acts as an angular mirror, reflecting the light beam from the EPI fluorescence illuminator vertically downward through the objective toward the specimen.

This fluorescence filter cube fits the following EPI fluorescence microscopes:
- Carl Zeiss Jena Fluoval Fluoreszenz
- Carl Zeiss Jena Fluoval-2 (built on the Carl Zeiss Jena Amplival microscope platform)

Important - this microscope component does not fit the first version of the Carl Zeiss Jena Fluoval microscope. The Fluoval microscope (without "2") does not use a filter cube. Instead, it has a simple permanently mounted swing-out barrier filter.

The filter cube has two positions:
- empty, for normal transmitted-light operation
- 450 nm for reflected-light fluorescence (EPI) operation

Mechanically, this filter cube is installed between the objective nosepiece and the microscope head. It slides into a dedicated slot and moves along a dovetail guide. On the Carl Zeiss Jena Laboval Fluoreszenz microscope, this slot is located in the additional upper horizontal arm of the EPI fluorescence illuminator. On the Carl Zeiss Jena Fluoval-2 microscope, the slot is located in the EPI fluorescence arm, which is an integral part of the microscope. The Fluoval-2 is based on the Carl Zeiss Jena Amplival microscope, which has a modular design. Mechanically, the Fluoval-2 is essentially an Amplival equipped with an upper EPI fluorescence arm.

Sliding the cube along this dovetail guide switches between the empty position (transmitted light) and EPI fluorescence with the 450 nm filter.

Description of this part for the microscope.

diameter: 23.2 mm

This eyepiece allows the microscope image to be projected onto a surface such as a wall, ceiling or projection screen.

Originally, this eyepiece model was supplied with the Carl Zeiss Jena Pictoval projection microscope. It can also be installed on virtually any microscope from any manufacturer with a 23.2 mm eyepiece tube.

Important: Projecting a microscope image requires a very large amount of light, so a high-power illuminator is necessary.

Description of this part for the microscope.

This filter is mounted in the sheet-metal housing of the large HBO 250W fluorescence illuminator. This illuminator is part of a large mirror light beam splitter used in Carl Zeiss Jena Jenalumar microscopes. The KG filter is designed to absorb heat (infrared radiation) emitted by the high-pressure HBO mercury lamp.

Please note that there is also a version of the Carl Zeiss Jena Jenalumar microscopes with a small 50W HBO illuminator. This KG filter glass was removed from a large 250W illuminator.

On the used market, in microscopy forums and in microscopy groups, several names are used for this filter, all referring to the same type of filter:
- KG filter / KG glass
- heat filter
- heat absorbing filter
- heat absorption filter
- heat-absorbing glass
- heat absorption glass
- absorption filter
- IR filter
- infrared blocking filter
- infrared cut filter
- KG3 heat absorption filter

This microscope element is highly susceptible to damage. When this happens, the filter needs to be replaced, for example with the filter presented here. Here are examples of damage that can occur during use of the fluorescence illuminator and reasons why replacement of the filter may be necessary:
- the KG filter may crack or become cloudy due to overheating
- the filter may also chip or break as a result of mechanical damage, for example during transport
- the filter may sometimes be damaged during improper maintenance

High-performance heat filters such as this KG filter used with a 250W lamp are very often used by people building their own DIY projects. The housing with screw mounting makes this particularly convenient.

The last photo in the gallery shows the housing of the HBO 250W illuminator (lampenhaus), with an arrow indicating which element is being described and where it is located inside the illuminator. This makes it possible to identify the element unambiguously.

Description of this part for the microscope.

susceptible to damage, and good and efficient passive cooling is very important in an HBO 250W illuminator.

In Carl Zeiss Jena Jenalumar microscopes, the large HBO 250W fluorescence illuminator is attached to the Spiegelhaus for light beam splitting. It has two such heat sinks - one at the bottom and one at the top of the lamp housing.

For certainty, the photo gallery shows the exact dimensions of this element. The last photo shows the complete illuminator from which this element was removed, allowing the compatibility to be confirmed with certainty.

Description of this part for the microscope.

fluorescence illuminator behind the high-pressure mercury burner. In Carl Zeiss Jena Jenalumar microscopes, the large HBO 250W fluorescence illuminator is attached to the Spiegelhaus for light beam splitting.

The function of this element is to collect and reflect toward the KG filter the light that "shines and escapes to the rear".

This mirror, located directly next to the light source, is susceptible to damage, among other things due to exposure to high temperatures. Additionally, when the high-pressure mercury burner explodes (which occasionally happens), the mirror is very often damaged by the explosion.

The photo gallery shows the exact dimensions of this element. The last photo shows the HBO 250W illuminator for a Carl Zeiss Jena Jenalumar microscope, allowing the compatibility to be confirmed with certainty.

Description of this part for the microscope.

head in Carl Zeiss Jena Pictoval projection microscopes (microprojectors). The adjustable tilt angle of the eyepiece tube, which held a projection eyepiece (usually f=100), allowed the position of the projected image on the projection surface to be changed.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Eyepiece mounting diameter: 23.2 mm
Mounting to the microscope arm: 41 mm diameter dovetail ring

Because this microscope head has a Carl Zeiss Jena standard microscope mount (a 41 mm diameter dovetail ring), it can be mounted on most microscopes from this manufacturer (e.g. Carl Zeiss Jena Eduval, Laboval, Ergaval, Amplival, etc.), as well as on microscopes made by Lomo (e.g. Lomo Biolam), IOR and Meopta.

It seems useful to mention a few points:
- never look through this microscope head with the naked eye if a projection eyepiece is installed in it and the head is mounted in a Carl Zeiss Jena Pictoval microprojector. This may result in loss of eyesight due to the very high light output emitted by this microscope
- when mounting this microscope head on a microscope other than a Carl Zeiss Jena Pictoval, a different magnification scale may be obtained than with the original heads designed for the particular microscope model
- projecting a microscope image requires a great deal of light, i.e. a powerful illuminator. This is worth remembering if you intend to use this head to project an image from biological microscopes with standard incandescent illumination (e.g. 15 W 6 V), which is definitely not sufficient
- visual observation using this microscope head may be inconvenient because it has a different (smaller) tilt angle than standard monocular or binocular microscope heads

Description of this part for the microscope.

here is not a standalone lamp housing (such as part number 99693 in this database). It is an internal component of the large, integrated illuminator used in Carl Zeiss Jena Jenalumar 250 microscopes.

Carl Zeiss Jena Jenalumar microscopes are available in two main versions:
1. with two small illuminators - with a separate 6 V 25 W halogen illuminator in a small housing (for transmitted light) and a separate HBO 50 W fluorescence illuminator in a small housing (for reflected light)
2. with a large, integrated module consisting of a mirror light splitter, an integrated transmitted-light module with a 6 V 25 W halogen lamp, and a large lamp housing for HBO 250 W fluorescence illumination

The component offered here is part of the second version of the Jenalumar microscope.

Basic parameters of this illuminator module:
Supported lamp: Narva HLWS 6 V 25 W halogen lamp
6 V power connection: this illuminator is connected to the distributor rail (see part number 99679 in this database)
Cooling: passive, in two ways. The Narva HLWS lamp has integrated cooling in the form of "wings", while the entire illuminator is covered with a cover incorporating a finned heat sink (this is a separate component and is not part of the illuminator offered here)

The photo gallery shows the exact dimensions of this component. The last photo shows the complete HBO 250 W illuminator for the Carl Zeiss Jena Jenalumar microscope, with an arrow indicating this halogen illuminator module. This makes it possible to identify exactly where this component is located within the complete large microscope illuminator.

Description of this part for the microscope.

meters:
Manufacturer: Carl Zeiss Jena
Designation: Apl. 1,4
Name of the mount according to the manufacturer's catalogue: Kondensoreinhänger mfl 2, Bestellnummer 301080:021.26/0
Name of the condenser according to the manufacturer's catalogue: Aplanatischer Kondensor 1.4 mo / ms (applies only to the upper optical part)
Name of the condenser according to the manufacturer's catalogue: Kondensor hoher Lichtstärke mit Vorschaltsystem (applies to the entire module)
Version: grey colour with a black upper lens. Variant with a "dot" in the name after "Apl"
Numerical aperture N.A.: 1.4
Aperture diaphragm: yes, attached to the condenser mount
Wide-field lens: yes, it can be swung out of the optical path. This is the version with the large lens in a housing (see description below)
Removable upper lens: yes, it can be rotated
Mounting diameter: the optical part (condenser without diaphragm) has a mounting diameter of 39.5 mm and can be unscrewed from the condenser mount
Operating modes: the condenser can be used both as a dry condenser and as an immersion condenser

The entire part consists of the following elements:
- upper Apl. 1,4 lens
- screw-on/removable condenser (mo / ms)
- iris diaphragm screwed onto the condenser mount
- condenser mount model mfl 2
- swing-out wide-field lens
- two centering screws

This condenser is mainly used in Carl Zeiss Jena Fluoval / Fluoval-2 fluorescence microscopes. It is optimal for use with high-numerical-aperture apochromatic microscope objectives. For precisely this reason, users often install it on Carl Zeiss Jena Ergaval and Carl Zeiss Jena Amplival microscopes equipped with apochromatic objectives (Carl Zeiss Jena Apochromat).

It is worth mentioning again that this condenser can be used in two modes:
- without immersion oil on the upper lens of the condenser. In this case, it operates as a "dry condenser" and its numerical aperture N.A. is 0.9.
- with immersion oil on the upper lens of the condenser (i.e. underneath the microscope slide). In this case, it operates as an "immersion condenser" and its numerical aperture N.A. is 1.4, allowing a very bright image to be obtained - this is important in fluorescence microscopy or when using high-N.A. immersion objectives.

During production, this condenser was available in several versions:
- with a black upper lens, a dot in the model name (Apl. 1,4) and a wide-field module consisting of a single lens
- with a black upper lens, without a dot in the model name (Apl 1,4) and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a wide-field module consisting of two independently swing-out lenses, each on its own mount

I have not found any information anywhere as to whether the above-mentioned versions differ in their operation. From experience, I know that they are used interchangeably - but I do not know whether any differences in operation can actually be noticed.

Mechanically, this condenser is mounted on dovetail rails located underneath the microscope stage. In Carl Zeiss Jena Ergaval microscopes, this is a separate condenser mounting block, whereas in Carl Zeiss Jena Fluoval / Amplival microscopes, the dovetail is located on the microscope stage holder block.

The manufacturer describes this condenser as follows: "High-intensity condenser with an auxiliary system for illuminating large fields while imaging the field diaphragm. [...] The condenser of the FLUOVAL 2 can be used as a dry and immersion condenser of the highest aperture to achieve the highest possible excitation intensity. It is equipped with a switchable wide-field system that illuminates the large fields of low-power objectives while providing a sharp image of the field diaphragm in the object plane."

Description of this part for the microscope.

meters:
Manufacturer: Carl Zeiss Jena
Designation: Apl. 1,4
Name of the mount according to the manufacturer's catalogue: Kondensoreinhänger mfl 2, Bestellnummer 301080:021.26/0
Name of the condenser according to the manufacturer's catalogue: Aplanatischer Kondensor 1.4 mo / ms (applies only to the upper optical part)
Name of the condenser according to the manufacturer's catalogue: Kondensor hoher Lichtstärke mit Vorschaltsystem (applies to the entire module)
Version: grey colour with a black upper lens. Variant without the "dot" in the name after "Apl"
Numerical aperture N.A.: 1.4
Aperture diaphragm: yes, attached to the condenser mount
Wide-field lens: yes, it can be swung out of the optical path. This is the version with the large lens in a housing (see description below)
Removable upper lens: yes, it can be rotated
Mounting diameter: the optical part (condenser without diaphragm) has a mounting diameter of 39.5 mm and can be unscrewed from the condenser mount
Operating modes: the condenser can be used both as a dry condenser and as an immersion condenser

The entire part consists of the following elements:
- upper Apl 1,4 lens
- screw-on/removable condenser (mo / ms)
- iris diaphragm screwed onto the condenser mount
- condenser mount model mfl 2
- swing-out wide-field lens
- two centering screws

This condenser is mainly used in Carl Zeiss Jena Fluoval / Fluoval-2 fluorescence microscopes. It is optimal for use with high-numerical-aperture apochromatic microscope objectives. For precisely this reason, users often install it on Carl Zeiss Jena Ergaval and Carl Zeiss Jena Amplival microscopes equipped with apochromatic objectives (Carl Zeiss Jena Apochromat).

It is worth mentioning again that this condenser can be used in two modes:
- without immersion oil on the upper lens of the condenser. In this case, it operates as a "dry condenser" and its numerical aperture N.A. is 0.9.
- with immersion oil on the upper lens of the condenser (i.e. underneath the microscope slide). In this case, it operates as an "immersion condenser" and its numerical aperture N.A. is 1.4, allowing a very bright image to be obtained - this is important in fluorescence microscopy or when using high-N.A. immersion objectives.

During production, this condenser was available in several versions:
- with a black upper lens, a dot in the model name (Apl. 1,4) and a wide-field module consisting of a single lens
- with a black upper lens, without a dot in the model name (Apl 1,4) and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a wide-field module consisting of two independently swing-out lenses, each on its own mount

I have not found any information anywhere as to whether the above-mentioned versions differ in their operation. From experience, I know that they are used interchangeably - but I do not know whether any differences in operation can actually be noticed.

Mechanically, this condenser is mounted on dovetail rails located underneath the microscope stage. In Carl Zeiss Jena Ergaval microscopes, this is a separate condenser mounting block, whereas in Carl Zeiss Jena Fluoval / Amplival microscopes, the dovetail is located on the microscope stage holder block.

The manufacturer describes this condenser as follows: "High-intensity condenser with an auxiliary system for illuminating large fields while imaging the field diaphragm. [...] The condenser of the FLUOVAL 2 can be used as a dry and immersion condenser of the highest aperture to achieve the highest possible excitation intensity. It is equipped with a switchable wide-field system that illuminates the large fields of low-power objectives while providing a sharp image of the field diaphragm in the object plane."

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Serial number: 039 562 (039562)
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

pair"
Magnification: 2.5x (written in the old style as 2 1/2)
Housing: rough, i.e. the older version

Since the 1930s, Carl Zeiss Jena produced many models and variants of stereomicroscopes, and this objective will fit the vast majority of them, as they share the same mounting method.

Here (https://www.microscopeparts.eu/part/00654) you can see a 1.25x objective for the same microscope model.

Description of this part for the microscope.

microscope base. This metal element (in which the lens is mounted) also serves as a rail onto which the interchangeable filter holder slides (like this one: https://www.microscopeparts.eu/part/99383, this one: https://www.microscopeparts.eu/part/99404 or the one with a polarizer).

This element is used in the following microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Cast and die-cast metal parts made by Carl Zeiss Jena carry their own numbers. This part bears the number 2648 (full marking: 2648 Si10 CZ).

In the last photos of the gallery, an arrow shows exactly where this element sits in the microscope, so you can identify it without any doubt.

Description of this part for the microscope.

Jenaval and Jenalumar microscopes (and of Carl Zeiss Jena Jenavert microscopes, if they are equipped for transmitted light) holds a set of lenses that collimate the light beam. Together they form the Koehler illumination collector, even though they are not mechanically connected to each other.

Here I present a module consisting of:
- the second collector lens in the sequence
- the metal mount holding the lens
- the screws for fastening the mount with the lens to the microscope base

The last photos in the gallery show the complete base of a Carl Zeiss Jena Jenaval microscope. An arrow indicates which part this is and exactly where it sits, so the part can be identified unambiguously.

This lens in its mount fits the bases of the following microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Note - Carl Zeiss Jena Jenavert microscopes come in two versions: reflected light (EPI) only, and reflected (EPI) plus transmitted light. The lens presented here fits both versions, but in the version without transmitted light... it simply has nothing to do :)

This is a service part for anyone who needs to replace this particular part in their microscope. It is not a complete illumination collector.

Description of this part for the microscope.

17-A
Magnification: 50x
Numerical aperture N.A.: 0.95
Optical correction: Apochromat
Additionally: cover glass thickness correction collar, range 0.12 - 0.22 mm
Tube length: infinity
Thread: M25
Cover glass: yes, required
Immersion: no (so-called dry objective)

Commonly used, cheap cover glasses are 0.17 mm thick mostly on paper. Even the standard for class #1.5 allows a range of 0.16-0.19 mm, and cheap Chinese cover glasses in practice come in anywhere from approx. 0.13 to 0.25 mm, often not matching the thickness stated on the box. Only #1.5H (high precision) cover glasses have a guaranteed thickness of 0.170 mm with a tolerance of +/- 0.005 mm. With high-aperture dry objectives such as this Apochromat 50x/0.95, variation in cover glass thickness noticeably reduces image contrast and resolution (spherical aberration). The correction collar fitted to this objective lets you adjust the optics to the combined thickness of the cover glass and the mounting medium layer beneath it, within a range of 0.12 mm to 0.22 mm. This compensates for most of the variation encountered in practice.

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

As for the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

Description of this part for the microscope.

of view number: 12
Mounting diameter: 23.2 mm
Designation: PK = plan compensating - recommended for work with planachromatic objectives, but they also work without any trouble with achromats or apochromats

Because of their very high quality they are often used on microscopes from other manufacturers as well, especially when Carl Zeiss Jena Planachromat objectives are mounted in them. The "compatibility" section lists a long series of microscopes these eyepieces fit - but that list is definitely not complete.

Important: these eyepieces work both on microscopes with a finite tube length (160 mm, for example) and on microscopes with infinity optics. That means you can use them on the Carl Zeiss Jena Amplival microscope just as well as on the Carl Zeiss Jena NU-2 microscope.

A note - eyepieces with such a strong magnification are in my opinion better suited to a quick look than to permanent work. I write "in my opinion" on purpose, because this comes from using them and not from the manufacturer's description.
A 16x eyepiece magnification should be treated as a zoom that brings out no additional detail (the resolution is not increased). This matters for example with heads that have their own extra magnification (such as Carl Zeiss Jena heads with a built-in 1.5x or 1.6x factor) - working with a 100x oil immersion objective you then theoretically get 100*1.5*16 = 2400x, while physics does not allow light from the visible range to be usefully magnified for the human eye beyond roughly 1250x - so this is what is called empty magnification.

Description of this part for the microscope.

5x
Field of view number: 16
Mounting diameter: 23.2 mm
Designation: PK = plan compensating - recommended for work with planachromatic objectives, but they also work without any trouble with achromats or apochromats

Because of their very high quality they are often used on microscopes from other manufacturers as well, especially when Carl Zeiss Jena Planachromat objectives are mounted in them. The "compatibility" section lists a long series of microscopes these eyepieces fit - but that list is definitely not complete.

Important: these eyepieces work both on microscopes with a finite tube length (160 mm, for example) and on microscopes with infinity optics. That means you can use them on the Carl Zeiss Jena Amplival microscope just as well as on the Carl Zeiss Jena NU-2 microscope.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

be attached to a trinocular head or directly to the microscope body, even when there is no trinocular head.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: grey
Tilt angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to the trinocular head or microscope body: ring with a dovetail
Dovetail diameter: 41 mm
Type of connection at the output: empty tube / barrel
Tube diameter at the output: 23.2 mm internal diameter
Length of the barrel / tube: 25 mm
Length adjustment: no - this is not a tube with adjustable height

Since the adapter has an empty barrel with an internal diameter of 23.2 mm on the output side, a projection eyepiece of that diameter can be placed in it, or a so-called "USB eyepiece", that is a digital microscope camera. Adapters between the 23.2 mm barrel and the M42 thread are also widely available, and from the M42 thread you can move on to any other mount: Nikon, Canon, Sony and others.

Such a tube can be mounted directly on the microscope body instead of the head. A dovetail seat with a diameter of 41.0 - 41.5 mm is found, among others, on the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH

It is also often used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can equally well be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol microscopes
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in the LOMO Polam microscopes
- some versions of the intermediate photo tubes for the Carl Zeiss Jena Mikroval series microscopes (others require a tube screwed onto a thread)

This is not a "tube for one specific microscope model". A trinocular head can be mounted not only on the microscope it was sold with - it is therefore correct to assume that this is a universal tube, with a 41 mm dovetail on one side and a 23.2 mm barrel on the other.

The "compatibility" section gives an example list of microscopes this tube fits, although it is not a complete list.

Description of this part for the microscope.

Carl Zeiss Jena
Engraving on the objective: Planachromat 25x/0,50 ∞/0
Magnification: 25x
Numerical aperture N.A.: 0,50
Free working distance: 3,1 mm
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: no - this objective has no phase ring inside
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective calls for eyepieces with additional correction (designated "PK" by Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography by connecting the objective directly to a camera

This objective can be used as:
- an objective for work in reflected light (EPI), for biological as well as, among others, metallurgical or mineralogical applications
- an objective for work in transmitted light, among others with biological specimens or, for example, with mineralogical thin sections

A few facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes of this company:
- these objectives serve mostly technical applications and are intended for work without a cover glass (marking ∞/0)
- CZJ M19 objectives intended for biological applications (that is, marked ∞/0,17) are most often used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with the EPI illuminator and can then work both in bright field and in dark field
- in Carl Zeiss Jena Polmi-A microscopes, CZJ M19 objectives can be used, but they give a magnification other than the nominal one
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes have an interchangeable nosepiece, and there is also a nosepiece intended for these microscopes that accepts objectives with M19 thread
- Carl Zeiss Jena Metaval microscopes use newer versions of CZJ M19 objectives (those with a coarsely knurled rim and a glossy barrel), yet many people experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various configurations - and some work with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow work with CZJ M19 objectives in EPI dark field mode
- on inverted metallographic Carl Zeiss Jena Epityp-2 / Neophot-21 microscopes, many people use biological objectives intended for work with a cover glass alongside metallurgical ones, and place the slide with the specimen on the stage "upside down", that is, with the cover glass facing downwards

Description of this part for the microscope.

Jena microscopes over nearly 100 years. They differ in the appearance of the barrel and in the engraving.

Appearance of this variant of the Carl Zeiss Jena 8x objective:
- black section next to the thread
- silver upper section
- the marking "8/0,20 160/-" on one side of the silver part of the barrel
- the Carl Zeiss Jena logo and the serial number on the other side of the silver barrel

Here (https://www.microscopeparts.eu/part/99852) you will see the same Carl Zeiss Jena 8x objective, but in a slightly older variant (without the value "160/-" engraved on the barrel).

The Carl Zeiss Jena 8x objective is often used for macro photography - both on a microscope and on a camera (with an RMS adapter or a bellows unit). Although it is an achromatic objective, it renders fine detail very well and works nicely for focus stacking. It is a good complement to a set together with the Carl Zeiss Jena Semiplan 3.2x, LOMO 3.7x, Carl Zeiss Jena Semiplan 6.3x and Nikon M Plan 10x objectives.

Basic parameters of this objective:
Manufacturer: Carl Zeiss Jena
Magnification: 8x
Correction: achromatic
Marking on the objective: 8/0,20 160/-
Numerical aperture N.A.: 0.20
Serial number: above 580 000
Tube length: 160 mm
Parfocal length: 33 mm - a so-called short barrel objective
Cover glass: either way - objectives with such a low magnification can work both with and without a cover glass
Immersion: no (a so-called dry objective)
Thread: RMS

Important - this objective is suitable for taking pictures with the "direct-projection" technique, because it does not require plan-compensating optics.

A microscope objective with such a low magnification (keeping the 160 mm tube we get an 8:1 reproduction ratio) is used for observation or macro photography of, among other things:
- insects
- minerals
- inclusions in amber
- handwriting
- micro shells

Why do I describe the appearance of this variant so precisely in the description of this objective? Some users care about completing their Carl Zeiss Jena microscope with parts from the same series and roughly from the same period. The exact way the parameters are written on the barrel makes it possible to compare this objective not only from the photos in the gallery, but also at the level of the text description - especially for AI systems.

This is a so-called "short barrel objective", with a parfocal length of 33 mm. Very often this objective is mounted on a 12 mm extension, which makes it possible to use it in microscopes that require objectives with a parfocal length of 45 mm. Professional adapters with corrective optics work well here, as do plain metal adapters and the popular DIY parts from a 3D printer.

This objective fits practically any microscope from any manufacturer, provided it has an RMS thread and supports objectives with TL=160 mm and a parfocal length of 33 mm (or 37 / 45 mm if we use a suitable adapter). A few examples of such microscopes are listed in the "compatibility" section, but that is not a complete list.

Carl Zeiss Jena objectives are very popular among users of microscopes from other manufacturers. Because of the historical connections, owners of LOMO microscopes treat them as an obvious replacement for their own Soviet optics.

After the Second World War the Carl Zeiss Jena production plant ended up in the Soviet occupation zone, and the Russians began copying the German technical documentation - see for yourself that the LOMO 8x objectives are an exact copy of the objective presented here: https://www.microscopeparts.eu/?search_2=8x&search_7=ob&search_8=lomo. The objectives made for school microscopes such as the Opta Junat are also a clone of Carl Zeiss Jena optics: https://www.microscopeparts.eu/part/00639.

Description of this part for the microscope.

Jena microscopes over nearly 100 years. They differ in the appearance of the barrel and in the engraving.

Appearance of this variant of the Carl Zeiss Jena 8x objective:
- black section next to the thread
- silver upper section
- the digit "8" on the first line and "0,20" on the second line, on one side of the silver part of the barrel
- the Carl Zeiss Jena logo and the serial number on the other side of the silver barrel

Here (https://www.microscopeparts.eu/part/99851) you will see the same Carl Zeiss Jena 8x objective, but in a slightly newer variant (with the value "160/-" engraved on the barrel).

The Carl Zeiss Jena 8x objective is often used for macro photography - both on a microscope and on a camera (with an RMS adapter or a bellows unit). Although it is an achromatic objective, it renders fine detail very well and works nicely for focus stacking. It is a good complement to a set together with the Carl Zeiss Jena Semiplan 3.2x, LOMO 3.7x, Carl Zeiss Jena Semiplan 6.3x and Nikon M Plan 10x objectives.

Basic parameters of this objective:
Manufacturer: Carl Zeiss Jena
Magnification: 8x
Correction: achromatic
Marking on the objective: 8 0,20
Numerical aperture N.A.: 0.20
Serial number: 503 729
Tube length: 160 mm
Parfocal length: 33 mm - a so-called short barrel objective
Cover glass: either way - objectives with such a low magnification can work both with and without a cover glass
Immersion: no (a so-called dry objective)
Thread: RMS

Important - this objective is suitable for taking pictures with the "direct-projection" technique, because it does not require plan-compensating optics.

A microscope objective with such a low magnification (keeping the 160 mm tube we get an 8:1 reproduction ratio) is used for observation or macro photography of, among other things:
- insects
- minerals
- inclusions in amber
- handwriting
- micro shells

Why do I describe the appearance of this variant so precisely in the description of this objective? Some users care about completing their Carl Zeiss Jena microscope with parts from the same series and roughly from the same period. The exact way the parameters are written on the barrel makes it possible to compare this objective not only from the photos in the gallery, but also at the level of the text description - especially for AI systems.

This is a so-called "short barrel objective", with a parfocal length of 33 mm. Very often this objective is mounted on a 12 mm extension, which makes it possible to use it in microscopes that require objectives with a parfocal length of 45 mm. Professional adapters with corrective optics work well here, as do plain metal adapters and the popular DIY parts from a 3D printer.

This objective fits practically any microscope from any manufacturer, provided it has an RMS thread and supports objectives with TL=160 mm and a parfocal length of 33 mm (or 37 / 45 mm if we use a suitable adapter). A few examples of such microscopes are listed in the "compatibility" section, but that is not a complete list.

Carl Zeiss Jena objectives are very popular among users of microscopes from other manufacturers. Because of the historical connections, owners of LOMO microscopes treat them as an obvious replacement for their own Soviet optics.

After the Second World War the Carl Zeiss Jena production plant ended up in the Soviet occupation zone, and the Russians began copying the German technical documentation - see for yourself that the LOMO 8x objectives are an exact copy of the objective presented here: https://www.microscopeparts.eu/?search_2=8x&search_7=ob&search_8=lomo. The objectives made for school microscopes such as the Opta Junat are also a clone of Carl Zeiss Jena optics: https://www.microscopeparts.eu/part/00639.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 25x/0,50 ∞/0 Ph
Magnification: 25x
Numerical aperture N.A.: 0,50
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) is the same objective in the version without phase rings. Its description tells you more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 12.5x/0.25 ∞/0 Ph
Magnification: 12.5x
Numerical aperture N.A.: 0.25
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) you can read more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 6.3x/0.12 ∞/0 Ph
Magnification: 6.3x
Numerical aperture N.A.: 0.12
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) you can read more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

Zeiss Jena
Lettering: Jenamed hematology
Material: aluminium
Length: 65 mm
Width: 12 mm
Mounting: the plate is glued on

By default, such a plate was fitted to every Carl Zeiss Jena Jenamed microscope in the "hematology" version. Since the adhesive used to attach these plates to the microscope body loses its properties over the years, these plates very often fall off.

Such a plate lets you bring your microscope back to its factory appearance using original parts.

Description of this part for the microscope.

a low-power survey condenser with low numerical aperture and a main condenser with high aperture. Both sit on a common carrier at the same time, which lets you switch between them. What I am offering here is the condenser alone, so without the carrier.

Parameters of this condenser:
Manufacturer: Carl Zeiss Jena
Numerical aperture N.A.: 0.12
Correction: aplanatic
Mounting: the condenser screws into a dedicated carrier. The thread diameter is 36 mm.
Iris diaphragm: yes, the condenser has a ring that opens and closes the diaphragm
Removable top lens: no
Intended use: this condenser model was fitted in Carl Zeiss Jena Jenaval microscopes

This condenser can also be screwed into the carrier of Carl Zeiss Jena Jenalumar microscopes - it is the same carrier as in Jenaval microscopes. Note, however, that Jenalumar microscopes came with a 0.20 N.A. condenser as standard (you can see it here: https://www.microscopeparts.eu/part/00530).

A condenser with such a low numerical aperture is intended for observation with low magnification microscope objectives (1.25x / 3.2x / 6.3x, 10x at most).

Description of this part for the microscope.

a survey condenser with low numerical aperture and a main condenser with high aperture. Both sit on a common carrier at the same time, which lets you switch between them. What I am showing here is the main one, with the 0.9 aperture - the condenser alone, so without the carrier.

Parameters of this condenser:
Manufacturer: Carl Zeiss Jena
Numerical aperture N.A.: 0.9
Correction: achromatic-aplanatic (Achr. apl.)
Immersion: no. This is a dry condenser
Mounting: the condenser carrier holds a centrable threaded ring, and the condenser screws into that ring. The thread diameter is 38 mm.
Iris diaphragm: not on the condenser - the diaphragm sits in the carrier, below the condenser
Intended use: this condenser model was fitted in Carl Zeiss Jena Jenaval microscopes

How it mounts in the carrier:
- The condenser carrier holds a threaded ring, and the ring itself is centrable - two centring screws do that job (these ones: https://www.microscopeparts.eu/part/00535).
- The screws set the position of the ring, and the condenser simply screws into that ring.
- Further down, in the same carrier, sits the iris diaphragm for this main condenser. It is centrable as well and has its own screws for that.

This condenser can also be screwed into the carrier of Carl Zeiss Jena Jenalumar microscopes - it is the same carrier as in Jenaval microscopes. Note, however, that Jenalumar microscopes run the Apl. 0.9 condenser from the factory, that is the aplanatic version without achromatic correction.

The Achr. apl. 0.9 condenser is the working condenser of these microscopes - it covers the whole range of dry objectives, but with immersion objectives it works without making use of their full aperture.

Description of this part for the microscope.

These screws fit the following Carl Zeiss Jena microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

The so-called "small illuminators", that is the halogen 25W one (like this: https://www.microscopeparts.eu/gallery/99693) or the HBO 50W, are held by two such screws. Large HBO 250W illuminators with an integrated power supply are mounted on 4 such screws.

If your microscope has only one small illuminator (for example a Jenaval with transmitted light or a Jenavert with EPI illumination), you can extend it with a second (also small) illuminator. You will then need two screws for that.

What is unusual (and sometimes the reason why a user cannot find these screws for a long time) is that they are unscrewed FROM THE FRONT of the microscope. The heads of these screws sit in openings cut into the white sheet-metal side covers of the microscope. You can see these covers with the screw openings here: https://www.microscopeparts.eu/gallery/99692.

Description of this part for the microscope.

camera to a trinocular head or directly to the microscope stand, even when there is no trinocular head at all.

This is a black tube with an upper element (barrel) 55 mm long. Here (https://www.microscopeparts.eu/gallery/91057) you can see a functionally identical adapter, but grey and with an upper barrel only 25 mm long.

Black adapters of this kind come from the era of the Carl Zeiss Jena L stands (models Carl Zeiss Jena Lg, Lumipan, Ng, Nf or Nu). The grey ones are newer, from the era of the Mikroval series (models Carl Zeiss Jena Laboval, Eduval, Ergaval or Amplival and Docuval).

The mounting fit is of course identical, so both can be used interchangeably.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: black
Inclination angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to a trinocular head or microscope stand: ring dovetail
Ring dovetail diameter: 41.5 mm
Type of connection at the output: empty barrel / tube
Tube diameter at the output: 23.2 mm inner diameter
Barrel / tube length: 55 mm
Tube length adjustment: no - this is not a height-adjustable tube

Because on the output side this adapter has an empty barrel with an inner diameter of 23.2 mm, you can place in it a projection eyepiece of that diameter or a so-called USB eyepiece, that is a digital microscope camera. In addition, adapters between the 23.2 mm barrel and the M42 thread are widely available, and from the M42 thread you can already move on to any other mount: Nikon, Canon, Sony and all the rest.

Such a tube can be mounted directly on the microscope stand, in place of the head. A seat for a ring dovetail of 41.0 - 41.5 mm diameter is found among others in the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH
- Gamma

It is also used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can likewise be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the microscopes Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in LOMO Polam microscopes
- some versions of the black intermediate photo tubes for the microscopes Carl Zeiss Jena Lg / Lumipan / Nf and of the grey ones from the Mikroval series (others require a tube that screws in on a thread)

This is not a tube for one particular microscope model. A trinocular head can be mounted not only on the microscope it was sold with, so the correct assumption is that this is a universal tube with a ring dovetail of 41.5 mm diameter on one side and a barrel of 23.2 mm diameter on the other.

In the compatibility section you will find an example list of microscopes this tube fits, although that list is not complete.

Description of this part for the microscope.

Jena
Inscription: logo "Carl Zeiss Jena" and text "Q1 MADE IN DDR"
Material: aluminium
Length: 52 mm
Width: 14 mm
Mounting: the nameplate is glued on

By default such a nameplate was fitted to most Carl Zeiss Jena microscopes from the Mikroval series onwards. There is also a smaller nameplate - with the manufacturer logo only (without the "Q1 Made in DDR" text). You can see it here: https://www.microscopeparts.eu/part/00604.

Because the adhesive used to attach these plates to the microscope body loses its properties over the years, these plates very often fall off. A nameplate like this makes it possible to restore the factory appearance of a microscope using original parts.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP425
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - because this is an interference filter (it has a mirrored surface), the angle at which the filter sits relative to the incoming light matters and affects its parameters.

The coating on interference filters is sensitive not only to mechanical damage, for example scratches from improper storage or cleaning. Several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP490
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - this is an interference filter, which you can tell from the mirrored surface. For that reason the angle at which the filter sits relative to the incoming light matters and affects its parameters.

The coating on interference filters is sensitive to mechanical damage, for example scratches from improper storage or cleaning. Age is a separate matter - several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP560
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - the mirrored surface gives away that this is an interference filter. With filters of this kind the angle to the incoming light is not indifferent and affects their parameters.

The coating on interference filters is sensitive to mechanical damage, for example scratches from improper storage or cleaning. The second enemy is time - several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B226g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The letter "g" at the end of the designation is short for the German gehärtet, meaning toughened - the manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red passed by that filter and to narrow the excitation band further.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B228g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The "g" at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red that filter passes and to narrow the excitation band further.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B229g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The "g" at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red that filter passes and to narrow the excitation band further.

Description of this part for the microscope.

filter:
Manufacturer: Carl Zeiss Jena
Model: U204g
Filter type: glass excitation filter for UV fluorescence (the manufacturer calls it Erregerfilter)
Glass type: UG 1
Diameter: 32 mm
Thickness: 2 mm
Colour: black-violet, passes very little visible light
Toughened version: yes

The g at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature. With a UV excitation filter this matters especially, because it sits at the hottest point of the whole path and absorbs most of the burner energy.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

The manufacturer catalogue gives the following transmission values for this glass at 2 mm thickness:
- 0.015 at 302 nm
- 0.093 at 312 nm
- 0.435 at 334 nm
- 0.644 at 366 nm

Across the whole visible range, from 405 to 644 nm, transmission is zero. This means the filter works almost entirely on the 366 nm mercury line, exactly where the HBO burner is strongest in the ultraviolet.

One property of this glass is worth knowing: above 700 nm it starts to transmit again, and at 750 nm transmission reaches 0.210. This infrared leak is invisible to the eye, but it heats the specimen and spoils contrast in photographs.

In the excitation path U204 is also combined with a red-absorbing filter. The manufacturer documentation shows such a pair with the B226 filter, which cleans up the excitation band further.

The same UG 1 glass was supplied in two thicknesses, each with its own designation:
- The Carl Zeiss Jena U204 filter is UG 1 glass 2 mm thick
- The Carl Zeiss Jena U205 filter is UG 1 glass 4 mm thick

The thicker U205 cuts more sharply, but passes about a third less energy on the 366 nm line, so the image is noticeably darker.

A safety note: this filter passes ultraviolet, which is invisible and harmful to the eyes. When working with it, never look into the illumination path without a barrier filter in place.

Description of this part for the microscope.

Carl Zeiss Jena NU microscope (this socket carries the number 44 in the instruction manual). It measures the brightness of the image, from which the exposure time for photographs is determined.

The instruction manual for the Carl Zeiss Jena NU microscope is made available by the excellent site mikroskop-online.de here: https://www.mikroskop-online.de/mikroskope/wp-content/uploads/simple-file-list/Mikroskop-Bedienanleitungen-Druckschriften-Carl-Zeiss-Jena-Mikroskopen/30-040-1_G-Grosses-Universal-Forschungsmikroskop-NU-T.pdf

Description of this part for the microscope.

following microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

Each of these discs has 5 seats that take filters of 32 mm diameter. The filters are locked in place by a springy retaining ring (a so-called Sprengring) so that they cannot fall out. The set offered here comes with 10 such rings. Since each wheel can be loaded with five filters, the total number of possible combinations is 25.

At the moment these filter seats are empty. Neither wheel has any filters fitted - you are free to load them with whatever filters you like.

This two-wheel module fits halogen, HBO and XBO lamphouses.

Parts made by Carl Zeiss Jena, cast or injection moulded from ZnAl alloy, carry their own numbers by which they can be identified. This double filter revolver module consists of 3 cast components:
- 2672 Si10 CZ - the frame carrying both wheels. It is at the same time the outer cover plate with which the whole module is screwed onto the lamphouse
- 2957 Si10 CZ - the thick filter wheel
- and note: the thin filter wheel also carries the number 2957 Si10 CZ, which is unusual for this manufacturer - that two parts differing in dimensions should share the same number

This double filter wheel is sometimes also called:
- double filter holder
- double filter turret
- dual filter carrier
- double filter slider
- double filter changer

Here https://www.microscopeparts.eu/part/99693 you can see what a complete 6V 25W halogen illuminator looks like with a single filter wheel fitted. The double set offered here fits such an illuminator among others, so the single filter wheel from the illuminator of a Carl Zeiss Jena Jenaval microscope can, for example, be replaced by the double one.

Description of this part for the microscope.

microscopes, a so-called "objective pair"
Magnification: 2.5x
Anti-reflective coating: yes, this is an objective carrying the red letter "T", i.e. T-coated

On the black plastic housing the magnification is written as "2,5" - unlike the older versions of such objectives (made for the Stereomikroskop XII model), where the format used was "2 1/2" (see here: https://www.microscopeparts.eu/part/91035)

In stereo microscopes built on the Greenough principle, what is called "the microscope objective" is in fact a pair (two pieces) of objectives set at a specific angle to each other. This is exactly why the housings of older examples of such objectives (more precisely: the common housing covering the pair of objectives) carried two serial numbers. Each of these objectives simply had its own individual serial number. Such a case can be seen on this 1.25x objective: https://www.microscopeparts.eu/part/00654.

This technical design has a very interesting consequence - each single objective, once taken out of the housing, becomes an interesting choice for anyone working in macro photography, all the more so because these are usually low-magnification objectives, which are exactly what macro photography looks for.

Since the 1930s Carl Zeiss Jena has produced many models and variants of stereo microscopes, and this objective will fit the vast majority of them, because the way they are mounted is the same throughout.

Several names are in use on the market for the stereo microscope this objective comes from:
- Carl Zeiss Jena Stereomikroskop XVI
- Carl Zeiss Jena Präpariermikroskop XVI
- Carl Zeiss Jena Stereomikroskop PM XVI
- Carl Zeiss Jena SM XVI
- Carl Zeiss Jena PM XVI

Sometimes, to avoid Roman numerals, you also come across the spellings "SM-16" and "PM-16".

Interestingly, in the instruction manual from 1954 available online (https://www.microscopemuseum.eu/catalogues/Carl_Zeiss_1954_Stereomikroskop_PM_XVI.pdf), the header on page 3 reads "Stereomikroskop PH XVI". I do not know whether this is an OCR error or an original misprint, but it means that this (incorrect) name may be in circulation as well - and all of the names listed above refer to one and the same microscope.