Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

I don't remember the specifications for the Jenatech.

Note: this is the version with the frosted glass; there are also versions without it.

Description of this part for the microscope.

This mounting screw fits most Carl Zeiss Jena microscopes of the CF250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenapol
- Jenatech
- Jenavert

Carl Zeiss Jena developed a complete modular microscope system based on connections using this type of screw. Therefore, this screw as a service part is also compatible with most accessories, modules and microscope elements that can be mounted to the microscope, including:
- magnification changers
- VIS analyzers
- trinocular heads
- Interphako heads

Important - carefully check the shape and dimensions of the screw to make sure it is the size you need. For example, the modular design of the Carl Zeiss Jena Amplival microscope is based on mounting screws of a different shape and size (search for it in this database to have a comparison).

Description of this part for the microscope.

molded parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the number 2580 (full designation: Si10 CZ 2580).

This is a service element (replacement part) for the trino head (head with photo output), suitable for Carl Zeiss Jena CF-250 microscopes. Please note that this is a microscope element for a microscope part (the trinocular head) and not a part for a specific microscope model.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the upper main part of the housing is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this housing DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the head, in order to clearly identify this part.

Many different names are commonly used for the trino head. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trino head
- trinocular head
- trinocular head unit
- photo dome
- photo tube
- inclined tube with photo output

Description of this part for the microscope.

assembly of two lenses
- knob for moving and shifting the lenses
- mechanism for moving and shifting the lenses

Metal, cast or injection-molded parts manufactured by Carl Zeiss Jena have their own identification numbers. In this mechanism the lens is mounted on a cast part marked with number 2582 (full marking: Si10 CZ 2582).

This is a service element (repair part) of the trinocular head (photo tube), suitable for Carl Zeiss Jena microscopes of the CF-250 series. Please note that this is an element (component) of a microscope part (German: "Fototubus") and not a part dedicated to a specific microscope model.

Carl Zeiss Jena microscopes of the CF-250 series have a modular design and the microscope part to which the eyepieces are mounted (commonly referred to as "head", "binocular" or "twin tube") is a separate element from the angle tube (sometimes the German term "Winkeltubus" is used). If the angle tube has a photographic output, it is referred to as a "photo tube". The Bertrand lens offered and described here is intended specifically for this microscope part.

Hinweis - Carl Zeiss Jena microscopes Jenapol and Jenatech, although they also belong to the CF-250 series, have a differently designed photographic output and this mechanism DOES NOT FIT these models.

Hinweis - Carl Zeiss Jena also produced a simplified version of the photo tube which does not contain a Bertrand lens inside. In the image gallery there is also a page from the manufacturer's catalog so that it is visible whether these versions differ externally in appearance. This Bertrand lens shown and offered here CANNOT be installed in such a simplified version of the photo tube.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is concerned and where it is located in the head, in order to clearly identify this part.

In common usage many names are used for the photo tube. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trinocular head
- trinocular microscope head
- trinocular head assembly
- photo dome
- inclined tube with photo output

Description of this part for the microscope.

allows correction of vision in one eye and proper adjustment of image focus.

Basic parameters:
- Type: tube with diopter correction ring
- Diameter of supported eyepieces: 30 mm
- Color: white

Fits 30 mm heads used, among others, in the following Carl Zeiss Jena microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

Description of this part for the microscope.

250 series microscopes.
Note that this element is a component of a microscope element (the angled tube) and not a part dedicated to a specific microscope model.

This element fits, among others, the following Carl Zeiss Jena microscopes from the CF-250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenavert
- Jenatech
- Jenapol

Important: the element DOES NOT INCLUDE the screw used to secure the microscope head.

Inside this element there is a protective glass (without its own magnification, so called "zero lens") with a violet anti-reflection coating.
Although this holder for the binocular microscope head and the holder located at the photographic port look the same, have the same dimensions and are mechanically compatible - they are NOT (!) identical.
- the binocular microscope head mount contains a protective glass with a violet anti-reflection coating
- the mount located at the photographic port contains a protective glass with a green anti-reflection coating.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

250 series microscopes.
Note that this element is a component of a microscope element (the angled tube with photo port) and not a part dedicated to a specific microscope model.

This element fits, among others, the following Carl Zeiss Jena microscopes from the CF-250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenavert
- Jenatech
- Jenapol

Important: the element DOES NOT INCLUDE the screw used to secure the microscope head.

Inside this element there is a protective glass (without its own magnification, so called "zero lens") with a green anti-reflection coating.
Although this holder at the photographic port and the holder for the binocular microscope head look the same, have the same dimensions and are mechanically compatible - they are NOT (!) identical.
- the binocular microscope head mount contains a protective glass with a violet anti-reflection coating
- the mount located at the photographic port contains a protective glass with a green anti-reflection coating.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the element is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this part DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos.

Description of this part for the microscope.

suitable for Carl Zeiss Jena CF-250 microscopes. Please note that this is a microscope element for a microscope part (the trinocular head) and not a part for a specific microscope model.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the prism carrier is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this part DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the head, in order to clearly identify this part.

Many different names are commonly used for the trino head. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trino head
- trinocular head
- trinocular head unit
- photo dome
- photo tube
- inclined tube with photo output

Description of this part for the microscope.

holder into which a round filter with a diameter of 32 mm can be inserted
- the hinged, tilting cover allows the light output to be completely blocked

This slide-in element is used in the following microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Cast or injection-molded metal parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the numbers 2645 (full designation: Si10 2645) and 2683 (full designation: Si10 CZ 2683).

By default, in the basic versions of the CZJ Jenaval microscope, a simpler version of this element is installed - only a slide with a filter holder, without a light blocking cover.

In models with EPI illumination (de: Auflicht), such as Carl Zeiss Jena Jenavert and Carl Zeiss Jena Jenalumar, the transmitted light illuminator cover allows the transmitted light to be completely shut off when working exclusively with EPI illumination.

In the last photo in the gallery, the exact location of this element in the microscope is indicated with an arrow. This allows you to identify it precisely.

Description of this part for the microscope.

microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Cast or injection-molded metal parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the number 2645 (full designation: Si10 2645).

In the last photo in the gallery, the exact location of this element in the microscope is indicated with an arrow. This allows you to identify it precisely.

Description of this part for the microscope.

commonly used in microscopes with a 30 mm eyepiece mounting diameter:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older microscopes of the Mikroval series (e.g. Ergaval and Amplival) - in such cases this eyepiece will also fit them, because - in general - eyepieces fit the head mounted on the microscope, not the microscope itself.

A single Carl Zeiss Jena PW 6.3x (25) eyepiece can solve the following problems:
- a second 6.3x eyepiece is missing to complete a pair
- a low magnification eyepiece is needed for use in a trinocular photo tube

Description of this part for the microscope.

Jena
Name: Grossfeld Binocular
Eyepiece mounting diameter: 30 mm
Microscope mount: 41 mm dovetail mount
Diopter adjustment: yes, for one eyepiece

The set also includes two eyepieces:
- Model: Carl Zeiss Jena GF-Pw 10x (25)
- Mounting diameter: 30 mm

This head is most commonly used in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, widefield binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older Mikroval series microscopes (for example Ergaval and Amplival). If the microscope is additionally equipped with GF-Planachromat series widefield objectives (or GF-Planapochromat objectives used in Docuval microscopes) - this creates the best possible combination for Carl Zeiss Jena microscopes with a 160 mm tube length.

This microscope head model is identical to the Baader Mark V binocular viewer used in astronomical telescopes and is often purchased by astronomy enthusiasts and adapted for telescope mounting.

Description of this part for the microscope.

Variant, Cytology, Hematology, Histology, Jenamed-2, Fluorescence)
- Jenapol
- Jenavert
- Jenaval
- Jenatech
- Jenalumar

Please note - this is only the adjustment knob, that is the knob used by the microscope user to make the illumination brighter or dimmer. It is not a potentiometer and therefore not a part of the electrical circuit.

This knob features the characteristic white cap used on Carl Zeiss Jena microscopes, which is often lost during decades of microscope use.

Mechanically, this knob is attached to the potentiometer. The fixing screw is covered by a white metal cap.

In the last photo I indicate with an arrow exactly which element it is and where it is located in a Carl Zeiss Jena Jenamed microscope. In Jenaval and Jenalumar microscopes it is located on the microscope base.

Description of this part for the microscope.

allows two filters to be inserted into the EPI optical path, for example a frosted diffuser filter, a blue colour-balancing filter or a green filter used to facilitate metallurgical observations.

The photographs in the gallery show the exact dimensions of this slide.

Description of this part for the microscope.

Carl Zeiss Jena microscope heads with a wide field of view (German: Grossfeld) have one eyepiece tube with diopter adjustment and a second one without it. Here I present the tube without diopter adjustment (straight eyepiece tube).

Basic parameters:
- Type: straight eyepiece tube
- Compatible eyepiece diameter: 30 mm
- Colour: white

Compatible with 30 mm microscope heads used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

Description of this part for the microscope.

hand when adjusting the interpupillary distance. It is a rounded metal cover that protects the eyepiece prism located underneath.

The last photo in the gallery shows a complete microscope head. An arrow indicates exactly which component is being described and where it is located inside the head, making it easy to identify.

Carl Zeiss Jena wide field microscope heads (those designed for 30 mm eyepieces) have two such components (two prism covers). They protect the prisms of the right and left eyepieces. Both covers are identical and interchangeable, so there is no constructional difference between the right-hand and left-hand cover.

This is a component for a microscope head, not for a specific microscope model.

This component fits microscope heads designed for 30 mm eyepieces used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Metal cast or injection-moulded components manufactured by Carl Zeiss Jena have their own part numbers. This component is marked with the number 2630 (full designation: Si10 2630 / Si10 CZ 2630). In addition, the number "1" or "2" appears next to the part number to indicate whether it is the cover for the right-hand or left-hand prism. This is the only difference, because mechanically the right-hand and left-hand covers are identical.

Description of this part for the microscope.

the front, in the centre of the binocular head, between the two eyepiece tubes. It is a round cover plate (end cap) carrying a scale from 55 to 75 indicating the interpupillary distance (eyepiece tube spacing).

The last photograph in the gallery shows the complete binocular head. An arrow indicates the exact component being offered and its location within the head, allowing it to be identified unambiguously.

This is a component of the binocular head rather than a component dedicated to a particular microscope model.

This component fits 30 mm eyepiece binocular heads used, among others, on the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Description of this part for the microscope.

microscope head to the microscope.

Basic specifications:
Mount type: dovetail
Diameter: 41 mm, the Carl Zeiss Jena and Lomo standard
Internal thread: 34 mm

The last photograph in the gallery shows a complete binocular head. An arrow indicates exactly which component is being offered and where it is located on the head, making visual identification straightforward.

This is a component of the microscope head rather than of any specific microscope model.

This component fits 30 mm binocular heads used, among others, on the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

This 41 mm Carl Zeiss Jena dovetail mounting standard is commonly used:
- if you want to perform a DIY conversion and mount a microscope head from another manufacturer onto a Carl Zeiss Jena or Lomo microscope
- if you want to connect another dovetail-mounted accessory to a Carl Zeiss Jena or Lomo microscope, such as an Optovar magnification changer, a polarisation intermediate tube, a DIC head or an EPI reflected-light illuminator
- if you want to use the 34 mm internal thread to mount a photographic tube for a camera

Description of this part for the microscope.

knobs (via a pinion mounted on the shaft between the knobs) into the vertical movement of the integrated microscope stage and condenser support. This support is mounted on a dovetail guide, which is an integral part of the focusing block (included with this assembly).

This mechanism is suitable for the following microscope models:
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenavert

Description of this part for the microscope.

The complete set presented here consists of three components:
1. a small metal plate marked with the numbers 1 to 8 - these identify the terminal positions
2. an electrical tab terminal strip with eight terminals, housed in a plastic body
3. the rear sheet-metal cover of the microscope arm with the printed 6V illumination wiring diagram

This set was removed from a Carl Zeiss Jena Jenalumar microscope.

Components "1" and "2" (the numbered plate and the electrical tab terminal strip) are universal and fit the following microscope models:
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenavert
- Carl Zeiss Jena Jenapol

Component "3" (the rear sheet-metal cover of the microscope arm)
- fits the Carl Zeiss Jena Jenalumar microscope
- does not fit the Carl Zeiss Jena Jenaval microscope
- I do not know whether it fits the Carl Zeiss Jena Jenavert or Jenapol microscopes, as I have not personally tested this.

The 6V supply wires coming from the power supply are connected to the input terminals on the underside of this electrical tab terminal strip. The power supply is built into the microscope base. The lampenhaus fitted with a 6V 25W halogen bulb is connected to the output terminals on the upper side. In the Carl Zeiss Jena Jenaval and Jenalumar microscopes this supplies the transmitted-light illuminator. In the Carl Zeiss Jena Jenavert microscope it supplies the reflected-light illuminator.

In microscope versions equipped with two illuminators, only one of them can be powered from the power supply built into the microscope base, because the built-in power supply has a maximum output power of 25 W. The second illuminator requires an external power supply appropriate for the particular light source (a halogen lamp, a fluorescence light source, or - in the case of LED illuminators - an LED power supply with a dimmer).

This database also contains, under item number 99694, the same component together with the rear sheet-metal cover of the microscope arm from a Carl Zeiss Jena Jenaval microscope. You can compare the two versions to see the difference in the size of the rear sheet-metal cover between the Carl Zeiss Jena Jenaval and Jenalumar models.

If you need only one component from this set - either the rear microscope arm cover or only the electrical tab terminal strip - please contact us by email or through social media.

Description of this part for the microscope.

It is not an illuminator holder in the literal sense. The illuminator is secured with screws to the sides of the microscope's vertical arm. Instead, the central circular opening in this component is designed to receive and accurately position the cylindrical light-output section of the illuminator (lamphouse).

Microscopes designed for reflected-light operation (either exclusively or in addition to transmitted light), such as the Carl Zeiss Jena Jenalumar, Jenavert and Jenapol-U, have a different upper horizontal microscope arm from models intended exclusively for transmitted light, such as the Carl Zeiss Jena Jenaval. The reflected-light arm includes a slot for filter sliders, a slot for an aperture slider and, of course, an angled mirror.

Interestingly, this component is also present in Carl Zeiss Jena Jenaval microscopes, even though the standard version of this model is not equipped with an EPI reflected-light illuminator. Since it is not used there, it is normally covered by the rear sheet-metal cover of the microscope arm. This is exactly why the rear cover of the Carl Zeiss Jena Jenalumar microscope is shorter than that of the Jenaval model - it does not have to cover this component (see item no. 99679 in this database).

This component fits the following microscope models:
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenavert
- Carl Zeiss Jena Jenapol

- in the Carl Zeiss Jena Jenaval microscope this component is hidden behind the rear sheet-metal cover and is not used
- in the Carl Zeiss Jena Jenalumar 50 this component receives the small 50W HBO fluorescence illuminator
- in the Carl Zeiss Jena Jenalumar 250 with the large integrated lamphouse, this component receives the light-output section of the 250W HBO fluorescence illuminator
- in the Carl Zeiss Jena Jenavert this component receives the 50W/100W halogen illuminator
- Carl Zeiss Jena Jenapol microscopes may be equipped with various EPI reflected-light illuminators

Cast or injection-moulded ZnAl components manufactured by Carl Zeiss Jena carry identification numbers that allow them to be identified. This component bears the number 2650 (full marking: Si10 2650).

Description of this part for the microscope.

Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

The function of this microscope component is to reflect the light coming from the microscope base vertically upwards so that, after passing through the microscope slide with the specimen and the objective, it reaches the eyepieces and finally the user's eyes.

This component is a metal casting with a circular opening. The mirror is mounted in this opening. The complete assembly is fastened to the microscope base with screws.

Metal cast or injection-moulded microscope components manufactured by Carl Zeiss Jena carry identification numbers. The part to which the mirror is attached bears the number 2649 (full marking: Si10 CZ 2649).

Replacement of the right-angle mirror in Carl Zeiss Jena microscopes may be necessary in the following situations:
- if the mirror has become significantly scratched due to improper cleaning (minor scratches are usually not visible during normal use)
- if the reflective silver coating of the installed mirror has become oxidised
- if the mirror has been damaged, chipped or cracked, for example after becoming detached from its mount
- if the metal casting holding the mirror chips or breaks due to age, stresses caused by the mounting screw or mechanical damage

Description of this part for the microscope.

The complete set presented here consists of three components:
1. a small metal plate marked with the numbers 1 to 8 - these identify the terminal positions
2. an electrical tab terminal strip with eight terminals, housed in a plastic body
3. the rear sheet-metal cover of the microscope arm with the printed 6V illumination wiring diagram

This set was removed from a Carl Zeiss Jena Jenaval microscope.

Components "1" and "2" (the numbered plate and the electrical tab terminal strip) are universal and fit the following microscope models:
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenavert
- Carl Zeiss Jena Jenapol

Component "3" (the rear sheet-metal cover of the microscope arm)
- fits the Carl Zeiss Jena Jenaval microscope
- does not fit the Carl Zeiss Jena Jenalumar microscope
- I do not know whether it fits the Carl Zeiss Jena Jenavert or Jenapol microscopes, as I have not personally tested this.

The 6V supply wires coming from the power supply are connected to the input terminals on the underside of this electrical tab terminal strip. The power supply is built into the microscope base. The lampenhaus fitted with a 6V 25W halogen bulb is connected to the output terminals on the upper side. In the Carl Zeiss Jena Jenaval and Jenalumar microscopes this supplies the transmitted-light illuminator.

In microscope versions equipped with two illuminators, only one of them can be powered from the power supply built into the microscope base, because the built-in power supply has a maximum output power of 25 W. The second illuminator requires an external power supply appropriate for the particular light source (a halogen lamp, a fluorescence light source, or - in the case of LED illuminators - an LED power supply with a dimmer).

This database also contains, under item number 99679, the same component together with the rear sheet-metal cover of the microscope arm from a Carl Zeiss Jena Jenalumar microscope. You can compare the two versions to see the difference in the size of the rear sheet-metal cover between the Carl Zeiss Jena Jenaval and Jenalumar models.

If you need only one component from this set - either the rear microscope arm cover or only the electrical tab terminal strip - please contact us by email or through social media.

Description of this part for the microscope.

Jenapol
- Carl Zeiss Jena Jenalumar

This cover serves two main functions in the microscope:
- it protects the power supply and all electrical components built into the microscope base, protecting both the electrical system and the user from electric shock
- it protects the optical components located inside the microscope base from dust and other contamination

The base of Carl Zeiss Jena Jenaval, Jenalumar and similar microscopes contains part of the optical light path, and this area occasionally requires maintenance, especially cleaning. Since these microscopes are now more than 30 years old, it is not uncommon to find examples with this cover missing because it has been lost over the years.

Description of this part for the microscope.

Jena microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- can also be installed in a Carl Zeiss Jena Jenavert microscope to add transmitted-light capability

This component is located inside the microscope base. It receives the light beam from the illuminator, homogenises it (by diffusing the image of the lamp filament using a frosted filter acting as a diffuser) and then properly collimates it using a collimating lens. The prepared light beam then passes through another lens before reaching the right-angle mirror (sold as a separate component).

This part is well known on the secondary market among hobbyists and engineers building their own DIY optical projects, where it is frequently reused.

Interestingly, microscope versions intended exclusively for reflected-light operation (for example, the basic versions of the Carl Zeiss Jena Jenavert) do not contain this component because they do not have a transmitted-light optical path. However, both the microscope arm and the microscope base are identical to those used in transmitted-light models. This makes it possible to upgrade such an EPI microscope for transmitted-light operation by installing the complete lower transmitted-light optical path. The component offered here is one of the parts required for this conversion.

In the last photograph, an arrow indicates where this component is located inside the microscope, making it easy to identify.

Description of this part for the microscope.

Jena microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

This component serves almost exclusively a cosmetic purpose. At both the top and bottom of the sheet-metal cover there are openings through which the long screws pass. These screws secure the transmitted-light lamp housing to the rear of the microscope body (at the bottom) or the reflected-light EPI lamp housing (at the top).

Each microscope has two of these sheet-metal covers - one on the left side and one on the right. Both are identical, so there is no difference between the left-hand and right-hand cover.

The cover is attached using ordinary adhesive and, after many years, it may simply come loose and fall off. These covers are also sometimes lost during repairs or maintenance, so older microscopes are often missing them. Reattaching an original cover is an easy way to restore the microscope to its original appearance.

In the last photograph, an arrow indicates where this component is located on the microscope, making it easy to identify.

Description of this part for the microscope.

models:
1. Carl Zeiss Jena Jenaval
2. Carl Zeiss Jena Jenalumar
3. Carl Zeiss Jena Jenapol
4. Carl Zeiss Jena Jenavert

1. In Carl Zeiss Jena Jenaval microscopes, this lamp house is used as the transmitted-light illuminator.

2a. In Carl Zeiss Jena Jenalumar 50 microscopes (equipped with the small HBO 50 fluorescent lamp house, identical to the one used in Carl Zeiss Jena Jenamed Fluorescence microscopes), this lamp house serves as the transmitted-light source.

2b. Carl Zeiss Jena Jenalumar 250 microscopes are equipped with a large integrated lamp house. The unit offered here is therefore not compatible with this model.

3. In Carl Zeiss Jena Jenapol microscopes, this halogen lamp house is used both for transmitted light (mounted underneath) and for reflected light (mounted on the top). However, some Jenapol versions are equipped only for transmitted-light operation or only for reflected-light operation.

4. Carl Zeiss Jena Jenavert microscopes are normally equipped with a different lamp housing for reflected light. However, when the original unit is missing, users often modify a lamp house like the one offered here for DIY projects. In addition, if a Jenavert is equipped with a transmitted-light optical path, this lamp house is used as its transmitted-light source.

The lamp house is attached to the microscope using two long screws. Unusually - and this often makes them difficult to find - the screws are removed FROM THE FRONT of the microscope. Their heads are accessible through openings in the white sheet-metal side covers of the microscope body. These covers with the screw openings are shown in this database under item number 99692.

This lamp house contains a filter wheel with four positions for 32 mm diameter round filters. It is fitted with the same filter configuration originally supplied by Carl Zeiss Jena for the Jenaval model:
- one position is empty
- Carl Zeiss Jena C312 blue filter
- Carl Zeiss Jena D282 grey filter
- Carl Zeiss Jena V231 green filter

The filter wheel is an optional part of this lamp house. The example offered here is fitted with it, but it can be removed and the illuminator will still function perfectly as a light source.

Cast or injection-moulded ZnAl components manufactured by Carl Zeiss Jena carry identification numbers. The housing of this lamp house bears the number 2670 (full marking: 2670 Si10 CZ).

In the last photograph, an arrow indicates where this component is located in the microscope, making it easy to identify.

Description of this part for the microscope.

transformer assembly installed inside the microscope base. It converts an input voltage of 110-240 V into a 6 V output with a maximum power of 25 W. It is intended to power a halogen lamp house. An example of this lamp house can be found in this database under item number 99693.

This is not the power supply for the 50W/100W reflected-light lamp housing used on the Carl Zeiss Jena Jenavert. It is also not the power supply for the fluorescent lamp houses used on the Carl Zeiss Jena Jenalumar.

Compatible with the following microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

If you only need one component from this assembly - for example the transformer, one of the electronic circuit boards or just the potentiometer used to adjust the lamp brightness - please contact us by email or through our social media channels.

This complete assembly may be useful for solving the following microscope problems, among others:
- if the microscope illumination no longer works because of a faulty power supply. This may be caused by mains voltage surges, ageing electronic components or damage resulting from incorrect modifications (for example, conversion to LED lighting)
- if the illumination works but the brightness can no longer be adjusted because the potentiometer is worn out or defective

Originally, the complete power supply assembly (transformer, electronic circuit boards and wiring) is installed inside the microscope base, and it is offered here exactly in that configuration. How can it be used?
- the electrical components can be removed and used as spare parts to repair a damaged power supply
- the complete microscope base can be transplanted to another microscope (please note that it does not include any optical components)

An interesting DIY modification is to leave the power supply in the base offered here and then place the microscope on top of that base. This effectively raises the microscope while also providing an integrated power supply for a second lamp house.

Description of this part for the microscope.

microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- can also be installed in a Carl Zeiss Jena Jenavert microscope to add transmitted-light capability

This component is located inside the microscope base and enables the microscope illumination to be adjusted according to the Köhler illumination principle.

Interestingly, microscope versions intended exclusively for reflected-light operation (for example, the basic versions of the Carl Zeiss Jena Jenavert) do not include this transmitted-light field diaphragm because they do not have a transmitted-light optical path. However, the microscope base is identical to that used in transmitted-light models. This makes it possible to upgrade such an EPI microscope for transmitted-light operation by installing the complete lower transmitted-light optical path. The field diaphragm offered here is one of the components required for this conversion.

In the last photograph, an arrow indicates where the transmitted-light field diaphragm is located inside the microscope base, making this component easy to identify.

Description of this part for the microscope.

microscope base. This metal element (in which the lens is mounted) also serves as a rail onto which the interchangeable filter holder slides (like this one: https://www.microscopeparts.eu/part/99383, this one: https://www.microscopeparts.eu/part/99404 or the one with a polarizer).

This element is used in the following microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Cast and die-cast metal parts made by Carl Zeiss Jena carry their own numbers. This part bears the number 2648 (full marking: 2648 Si10 CZ).

In the last photos of the gallery, an arrow shows exactly where this element sits in the microscope, so you can identify it without any doubt.

Description of this part for the microscope.

Jenaval and Jenalumar microscopes (and of Carl Zeiss Jena Jenavert microscopes, if they are equipped for transmitted light) holds a set of lenses that collimate the light beam. Together they form the Koehler illumination collector, even though they are not mechanically connected to each other.

Here I present a module consisting of:
- the second collector lens in the sequence
- the metal mount holding the lens
- the screws for fastening the mount with the lens to the microscope base

The last photos in the gallery show the complete base of a Carl Zeiss Jena Jenaval microscope. An arrow indicates which part this is and exactly where it sits, so the part can be identified unambiguously.

This lens in its mount fits the bases of the following microscope models:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Note - Carl Zeiss Jena Jenavert microscopes come in two versions: reflected light (EPI) only, and reflected (EPI) plus transmitted light. The lens presented here fits both versions, but in the version without transmitted light... it simply has nothing to do :)

This is a service part for anyone who needs to replace this particular part in their microscope. It is not a complete illumination collector.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

be attached to a trinocular head or directly to the microscope body, even when there is no trinocular head.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: grey
Tilt angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to the trinocular head or microscope body: ring with a dovetail
Dovetail diameter: 41 mm
Type of connection at the output: empty tube / barrel
Tube diameter at the output: 23.2 mm internal diameter
Length of the barrel / tube: 25 mm
Length adjustment: no - this is not a tube with adjustable height

Since the adapter has an empty barrel with an internal diameter of 23.2 mm on the output side, a projection eyepiece of that diameter can be placed in it, or a so-called "USB eyepiece", that is a digital microscope camera. Adapters between the 23.2 mm barrel and the M42 thread are also widely available, and from the M42 thread you can move on to any other mount: Nikon, Canon, Sony and others.

Such a tube can be mounted directly on the microscope body instead of the head. A dovetail seat with a diameter of 41.0 - 41.5 mm is found, among others, on the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH

It is also often used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can equally well be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol microscopes
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in the LOMO Polam microscopes
- some versions of the intermediate photo tubes for the Carl Zeiss Jena Mikroval series microscopes (others require a tube screwed onto a thread)

This is not a "tube for one specific microscope model". A trinocular head can be mounted not only on the microscope it was sold with - it is therefore correct to assume that this is a universal tube, with a 41 mm dovetail on one side and a 23.2 mm barrel on the other.

The "compatibility" section gives an example list of microscopes this tube fits, although it is not a complete list.

Description of this part for the microscope.

The tube allows a camera or a camera body to be attached to a trinocular head or directly to the microscope body, even when there is no trinocular head.

Basic technical parameters of this tube:
Manufacturer: LOMO (ЛОМО)
Colour: black, rings and barrel chrome-plated
Tilt angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to the trinocular head or microscope body: ring dovetail (male part)
Dovetail diameter: 41 mm
Type of connection at the output: empty tube / barrel
Tube diameter at the output: 23.2 mm internal diameter
Length of the barrel / tube: variable
Length adjustment: yes - the barrel is extendable, with a scale from 140 to 200 mm and a knurled locking ring

This is the version with adjustable tube length. A scale from 140 to 200 mm is engraved on the extendable barrel, with a reference line and intermediate divisions, and the setting is locked with a knurled ring. This gives two things at once. First, a continuous change of the image scale - the longer the tube, the larger the image falling on the sensor or the film, so the framing can be adjusted without changing the objective. Second, and more importantly, the ability to work with objectives computed for different optical tube lengths: 160, 170, 180, 190 and 200 mm. Carl Zeiss Jena and LOMO objectives are computed for 160 mm, Leitz Wetzlar for 170 mm, some objectives of metallurgical and measuring microscopes for 190 or 200 mm - here you simply set the barrel to the right value and the objective works under its design conditions, instead of delivering an image with residual aberration.

Since the adapter has an empty barrel with an internal diameter of 23.2 mm on the output side, a projection eyepiece of that diameter can be placed in it, or a so-called "USB eyepiece", that is a digital microscope camera. Adapters between the 23.2 mm barrel and the M42 thread are also widely available, and from the M42 thread you can move on to any other mount: Nikon, Canon, Sony and others.

Such a tube can be mounted directly on the microscope body instead of the head. A dovetail seat with a diameter of 41.0 - 41.5 mm is found, among others, on the microscopes:
- LOMO
- Carl Zeiss Jena
- Meopta
- IOR
- Reichert Biopan
- Olympus CH

It is also often used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The "compatibility" section gives an example list of microscopes this tube fits, although it is not a complete list.

The last photo shows a LOMO Erudit microscope with this photo tube and a projection eyepiece mounted. It is an example of use.

Description of this part for the microscope.

These screws fit the following Carl Zeiss Jena microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

The so-called "small illuminators", that is the halogen 25W one (like this: https://www.microscopeparts.eu/gallery/99693) or the HBO 50W, are held by two such screws. Large HBO 250W illuminators with an integrated power supply are mounted on 4 such screws.

If your microscope has only one small illuminator (for example a Jenaval with transmitted light or a Jenavert with EPI illumination), you can extend it with a second (also small) illuminator. You will then need two screws for that.

What is unusual (and sometimes the reason why a user cannot find these screws for a long time) is that they are unscrewed FROM THE FRONT of the microscope. The heads of these screws sit in openings cut into the white sheet-metal side covers of the microscope. You can see these covers with the screw openings here: https://www.microscopeparts.eu/gallery/99692.

Description of this part for the microscope.

camera to a trinocular head or directly to the microscope stand, even when there is no trinocular head at all.

This is a black tube with an upper element (barrel) 55 mm long. Here (https://www.microscopeparts.eu/gallery/91057) you can see a functionally identical adapter, but grey and with an upper barrel only 25 mm long.

Black adapters of this kind come from the era of the Carl Zeiss Jena L stands (models Carl Zeiss Jena Lg, Lumipan, Ng, Nf or Nu). The grey ones are newer, from the era of the Mikroval series (models Carl Zeiss Jena Laboval, Eduval, Ergaval or Amplival and Docuval).

The mounting fit is of course identical, so both can be used interchangeably.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: black
Inclination angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to a trinocular head or microscope stand: ring dovetail
Ring dovetail diameter: 41.5 mm
Type of connection at the output: empty barrel / tube
Tube diameter at the output: 23.2 mm inner diameter
Barrel / tube length: 55 mm
Tube length adjustment: no - this is not a height-adjustable tube

Because on the output side this adapter has an empty barrel with an inner diameter of 23.2 mm, you can place in it a projection eyepiece of that diameter or a so-called USB eyepiece, that is a digital microscope camera. In addition, adapters between the 23.2 mm barrel and the M42 thread are widely available, and from the M42 thread you can already move on to any other mount: Nikon, Canon, Sony and all the rest.

Such a tube can be mounted directly on the microscope stand, in place of the head. A seat for a ring dovetail of 41.0 - 41.5 mm diameter is found among others in the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH
- Gamma

It is also used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can likewise be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the microscopes Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in LOMO Polam microscopes
- some versions of the black intermediate photo tubes for the microscopes Carl Zeiss Jena Lg / Lumipan / Nf and of the grey ones from the Mikroval series (others require a tube that screws in on a thread)

This is not a tube for one particular microscope model. A trinocular head can be mounted not only on the microscope it was sold with, so the correct assumption is that this is a universal tube with a ring dovetail of 41.5 mm diameter on one side and a barrel of 23.2 mm diameter on the other.

In the compatibility section you will find an example list of microscopes this tube fits, although that list is not complete.

Description of this part for the microscope.

following microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenavert

Each of these discs has 5 seats that take filters of 32 mm diameter. The filters are locked in place by a springy retaining ring (a so-called Sprengring) so that they cannot fall out. The set offered here comes with 10 such rings. Since each wheel can be loaded with five filters, the total number of possible combinations is 25.

At the moment these filter seats are empty. Neither wheel has any filters fitted - you are free to load them with whatever filters you like.

This two-wheel module fits halogen, HBO and XBO lamphouses.

Parts made by Carl Zeiss Jena, cast or injection moulded from ZnAl alloy, carry their own numbers by which they can be identified. This double filter revolver module consists of 3 cast components:
- 2672 Si10 CZ - the frame carrying both wheels. It is at the same time the outer cover plate with which the whole module is screwed onto the lamphouse
- 2957 Si10 CZ - the thick filter wheel
- and note: the thin filter wheel also carries the number 2957 Si10 CZ, which is unusual for this manufacturer - that two parts differing in dimensions should share the same number

This double filter wheel is sometimes also called:
- double filter holder
- double filter turret
- dual filter carrier
- double filter slider
- double filter changer

Here https://www.microscopeparts.eu/part/99693 you can see what a complete 6V 25W halogen illuminator looks like with a single filter wheel fitted. The double set offered here fits such an illuminator among others, so the single filter wheel from the illuminator of a Carl Zeiss Jena Jenaval microscope can, for example, be replaced by the double one.