Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

lenses:
- N.A. 0.3 for low-power objectives (this is the lens offered here)
- N.A. up to 1.4 (variable aperture) for high resolution and magnification
- oil dark field lens (cardioid condenser)

This condenser is used in Carl Zeiss Jena microscopes:
- Nf
- Nu / Nu2
- Lumipan
- Amplival (gray condenser)

but can also be mounted in the following microscopes:
- Jenaval
- Jenalumar
- Lu (I'm not sure)
- Ng
- Ergaval
- Docuval
- Polmi A

The companies IOR Bucuresti and Lomo made their own versions of pancratic condensers - I don't know if this lens is compatible with them.

Description of this part for the microscope.

Hohlspiegelkondensor 10)
- Carl Zeiss Jena Apochromat 32x microscope objective

Model: Hohlspiegelkondensor 10
Color: Black
Internal thread: M19

Objective:
---------
Manufacturer: Carl Zeiss Jena
Model: Apochromat 32x 0.65 oo
Tube length: infinity
Magnification: 32x
Numerical aperture: 0.65
Cover glass: no
Type: EPI (reflected light)
Thread: M19

This element is used for EPI observations in reflected light in microscopes with a suitable EPI illuminator (Auflichtkondensor) installed, e.g. Carl Zeiss Jena NF or NU / NU-2 and with Vertival, Epival, Epignost, BK 70x50 microscopes - although they are also available in versions supporting other objectives).

Description of this part for the microscope.

Hohlspiegelkondensor 9)
- Carl Zeiss Jena Planachromat 4x microscope objective

Model: Hohlspiegelkondensor 9
Color: Black
Internal thread: M19

Objective:
---------
Manufacturer: Carl Zeiss Jena
Model: Planachromat K 4x/0,05 oo/0 oo/2
Tube length: infinity
Magnification: 4x
Numerical aperture: 0.05
Cover glass: no OR 2 mm
Type: EPI (reflected light)
Thread: M19
Info: this microscope objective can work in oo/0 mode or after unscrewing the upper lens in oo/2 mode (e.g. for a Petri dish or through a microscope slide)

Mirror objective slides / inserts are used for EPI observations in reflected light in microscopes with a suitable EPI illuminator (Auflichtkondensor) installed, e.g. Carl Zeiss Jena NF or NU / NU-2 and with Vertival, Epival, Epignost, BK 70x50 microscopes - although they are also available in versions supporting other objectives).

Description of this part for the microscope.

NU / NU2
For: 63x Phv objective

The EPI condenser (illuminator) of the Carl Zeiss Jena NU and NU2 microscopes, while it may look similar to the one in the Nf model, is not identical, and many parts can be interchanged between these devices.
I'm not sure if this applies to this insert.

Description of this part for the microscope.

NU / NU2
For: 25x Phv objective

The EPI condenser (illuminator) of the Carl Zeiss Jena NU and NU2 microscopes, while it may look similar to the one in the Nf model, is not identical, and many parts can be interchanged between these devices.
I'm not sure if this applies to this insert.

Description of this part for the microscope.

NU / NU2
For: 10x Phv objective

The EPI condenser (illuminator) of the Carl Zeiss Jena NU and NU2 microscopes, while it may look similar to the one in the Nf model, is not identical, and many parts can be interchanged between these devices.
I'm not sure if this applies to this insert.

Description of this part for the microscope.

NU / NU2
For: 4x Phv objective

The EPI condenser (illuminator) of the Carl Zeiss Jena NU and NU2 microscopes, while it may look similar to the one in the Nf model, is not identical, and many parts can be interchanged between these devices.
I'm not sure if this applies to this insert.

Description of this part for the microscope.

NU / NU2
For: "0" - empty

The EPI condenser (illuminator) of the Carl Zeiss Jena NU and NU2 microscopes, while it may look similar to the one in the Nf model, is not identical, and many parts can be interchanged between these devices.
I'm not sure if this applies to this insert.

Description of this part for the microscope.

Description of this part for the microscope.

came from an EPI-POL illuminator for the Carl Zeiss Jena NU microscope, but as far as I know, the same sliders are compatible with the polarizing kit for the Carl Zeiss Jena Lg, NF, and Polmi-A polarizing microscopes. It's very possible it fits other configurations I'm not aware of, or even microscopes from other manufacturers.

Description of this part for the microscope.

Jena NU microscope, but as far as I know, the same sliders are compatible with the polarizing kit for the Carl Zeiss Jena Lg, NF, and Polmi-A polarizing microscopes. It's very possible it fits other configurations I'm not aware of, or even microscopes from other manufacturers.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Ergaval
- Amplival
- Docuval
- Metaval
- Epival
- Vertival
- Nf
- NU
- Epityp
- Epignost

Also for Carl Zeiss Jena devices and accessories such as:
- Winkeltube
- Pankratik Zoom-System
- Interphako
- and many others.

Note - some models have different dimensions for these screws, for example, longer ones.

Note - older models of the Carl Zeiss Jena Lg microscope use a different screw.

Note - the small screw at the front of this part unscrews in the OPPOSITE direction than most screws, and this is the most common cause of damage.

Description of this part for the microscope.

Ergaval
- Amplival
- Docuval
- Metaval
- Epival
- Vertival
- Nf
- NU

Note: Please examine the photos carefully. If I have more than one of this part, some of the screws may show traces of improper (forceful) unscrewing. These are not major traces - mostly minor scratches. Of course, they do not affect the functionality of the element at all.

Note - some models have different screw dimensions, for example, longer ones.

Note - in microscopes with a centering stage holder (for polarizing stages), this screw may be different.

Note - the small screw at the front of this part unscrews in the OPPOSITE direction than most screws, and this is the most common cause of damage.

Description of this part for the microscope.

NU2

This holder features two centering screws on the side, which are very important for polarization. The front retaining screw is also different from standard microscope stage holders (i.e., those without centering). Of course, standard stages, rectangular, round, and sliding EPI stages can also be used with this holder.

Description of this part for the microscope.

Hohlspiegelkondensor 12)
- Carl Zeiss Jena Planachromat 12,5x microscope objective

Model: Hohlspiegelkondensor 12
Color: Grey
Internal thread: M19

Objective:
---------
Manufacturer: Carl Zeiss Jena
Model: Planachromat 12,5x 0.25 oo/0
Tube length: infinity
Magnification: 12,5x
Numerical aperture: 0.25
Cover glass: no
Type: EPI (reflected light)
Thread: M19

This element is used for EPI observations in reflected light in microscopes with a suitable EPI illuminator (Auflichtkondensor) installed, e.g. Carl Zeiss Jena NF or NU / NU-2 and with Vertival, Epival, Epignost, BK 70x50 microscopes - although they are also available in versions supporting other objectives).

Description of this part for the microscope.

Hohlspiegelkondensor 12)
- Carl Zeiss Jena Planachromat 10x microscope objective

Model: Hohlspiegelkondensor 12
Color: Black
Internal thread: M19

Objective:
---------
Manufacturer: Carl Zeiss Jena
Model: Planachromat 10x 0.20 oo/-
Tube length: infinity
Magnification: 10x
Numerical aperture: 0.20
Cover glass: no
Type: EPI (reflected light)
Thread: M19

This element is used for EPI observations in reflected light in microscopes with a suitable EPI illuminator (Auflichtkondensor) installed, e.g. Carl Zeiss Jena NF or NU / NU-2 and with Vertival, Epival, Epignost, BK 70x50 microscopes - although they are also available in versions supporting other objectives).

Description of this part for the microscope.

eu/foto/owner-1/_manuals/Carl-Zeiss-Jena-MHP-160.pdf

Description of this part for the microscope.

polarized transmitted light with the possibility of use as a brightfield condenser
Mounting: the condenser is permanently integrated with a dovetail mount
Top lens: flip-out system allowing the upper lens to be moved into or out of the optical path to change the numerical aperture
Iris diaphragm: yes
Diffuser: yes, with the possibility of moving it into or out of the optical path
Polarizer: yes, rotatable, with the possibility of moving it into or out of the optical path

This condenser fits the following Carl Zeiss Jena microscope models:
- Polmi-A
- Nf
- Ng
- Nu / Nu2

Note: despite the visual similarity of the mounting interface, this condenser does NOT fit the Carl Zeiss Jena Lu microscope.

Important: the condenser is permanently integrated with the dovetail mount and cannot be used with other microscopes without significant modifications.

Description of this part for the microscope.

4 mo2 condenser holder that was used in the Carl Zeiss Jena Ergaval microscope. The same condenser (but with a different lower lens) is used in an identical holder in Fluoval microscopes. Condenser holders with such screws can also be found in the following microscopes:
- Docuval
- Amplival
- NU-2

The purpose of this spring screw is to push the clamp in which the condenser is mounted outward. Thanks to the spring integrated in the screw, it is possible to center the condenser using long centering screws (you can find such a centering screw in the database under number 99132).

In the last photo, an arrow clearly indicates which screw is meant and where it is mounted in the condenser holder.

Description of this part for the microscope.

that was used in the Carl Zeiss Jena Ergaval microscope. The same condenser (but with a different lower lens) is used in an identical holder in Fluoval microscopes. Condenser holders with such screws can also be found in the following microscopes:
- Docuval
- Amplival
- NU-2

In the last photo, an arrow clearly indicates which screw is meant and where it is mounted in the condenser holder.

Description of this part for the microscope.

this adapter allows operation of 1 objective at a time - this is not a objective turret (revolver)
- the adapter allows centering the objective relative to the optical axis, which is extremely important in polarization
- the adapter does not support objectives with RMS thread (approx. 20 mm)

Interesting fact:
This adapter fits the Carl Zeiss Jena Polmi-A microscope. This microscope is a construction designed for work with objectives with RMS thread and a tube length of 160 mm, but after using this adapter it is possible to use objectives with M19 thread corrected for infinity. Such tests were performed by Mr. Wojciech Plonka and he found that it works, but in this case the objectives produce stronger magnification than nominal (link: https://www.facebook.com/groups/254539018060854/?multi_permalinks=1857582481089825).

Description of this part for the microscope.

rotating the condenser, and for the condenser stopping in the correct position. This part is a plate that fits into the appropriate recess (detent).

Fits pancratic condensers used in the following microscopes:
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Nf
- Carl Zeiss Jena NU / NU2

Does not fit the gray pancratic condenser used in the Carl Zeiss Jena Amplival microscope.

In the photo gallery detailed photos of this element together with the dimensions are available. Additionally, in the last photo an arrow indicates which element it is and where it is located in the condenser in order to clearly identify this part.

Description of this part for the microscope.

Lumipan
- Carl Zeiss Jena Nf
- Carl Zeiss Jena NU / NU2

does NOT fit the gray pancratic condenser used in the Carl Zeiss Jena Amplival microscope.

In the photo gallery detailed photos of this element together with the dimensions are available. Additionally, in the last photo an arrow indicates which element it is and where it is located in the condenser in order to clearly identify this part.

Description of this part for the microscope.

Lumipan
- Carl Zeiss Jena Nf
- Carl Zeiss Jena NU / NU2

Does NOT fit the gray pancratic condenser used in the Carl Zeiss Jena Amplival microscope.

In the photo gallery detailed photos of this element together with the dimensions are available. Additionally, in the last photo an arrow indicates which element it is and where it is located in the condenser in order to clearly identify this part.

Description of this part for the microscope.

microscopes:
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Nf
- Carl Zeiss Jena NU / NU2

does NOT fit the gray pancratic condenser used in the Carl Zeiss Jena Amplival microscope.

In the photo gallery detailed photos of this element together with the dimensions are available. Additionally, in the last photo an arrow indicates which element it is and where it is located in the condenser in order to clearly identify this part.

Description of this part for the microscope.

microscopes:
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Nf
- Carl Zeiss Jena NU / NU2

Does not fit the gray pancratic condenser used in the Carl Zeiss Jena Amplival microscope.

In the photo gallery detailed photos of this element together with the dimensions are available. Additionally, in the last photo an arrow indicates which element it is and where it is located in the condenser in order to clearly identify this part.

Description of this part for the microscope.

probably fits most Carl Zeiss Jena microscope stages models

In the photo gallery there are detailed photos of this element together with the dimensions. Thanks to this it is possible to identify exactly which part of the microscope stage it is.

Description of this part for the microscope.

Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Nf
- Carl Zeiss Jena NU / NU2

does NOT fit the gray pancratic condenser used in the Carl Zeiss Jena Amplival microscope.

In the photo gallery detailed photos of this element together with the dimensions are available. Additionally, in the last photo an arrow indicates which element it is and where it is located in the condenser in order to clearly identify this part.

Description of this part for the microscope.

Carl Zeiss Jena Nf
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena NU / NU2

This lens DOES NOT FIT grey pancratic condensers from the following microscopes:
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Docuval

IOR Bucuresti and Lomo produced their own versions of pancratic condensers - I do not know whether this lens is compatible with them.

Description of this part for the microscope.

microscope objective
- Manufacturer: Carl Zeiss Jena
- Designation: Planachromat 25x/0,50 oo/0,17
- Magnification: 25x
- Numerical aperture N.A.: 0,50
- Optical correction: infinity-corrected tube length
- Optical correction class: planachromat
- Cover glass: yes, 0.17 mm
- Thread: M19

Some facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes from this manufacturer:
- these objectives are most commonly used for technical applications rather than biological applications, therefore most objectives available on the secondary market are intended for use without a cover glass (designation oo/0)
- CZJ M19 objectives intended for biological applications (designation oo/0,17) are most commonly used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with an EPI illuminator
- CZJ M19 objectives can be used in Carl Zeiss Jena Polmi-A microscopes, but they provide a different magnification than the nominal value
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes feature interchangeable nosepieces, and a dedicated nosepiece for M19-thread objectives was also produced for these microscopes
- Carl Zeiss Jena Metaval and Neophot microscopes use newer versions of CZJ M19 objectives (with a coarse-knurled edge and shiny housing), although many users still experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various versions with completely different configurations - and some of them operate with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow the use of CZJ M19 objectives in EPI dark-field mode
- on the Carl Zeiss Jena Epityp-2 inverted metallurgical microscope, many users employ biological objectives designed for use with a cover glass, placing the microscope slide "upside down", with the cover glass facing downward toward the objective.

Description of this part for the microscope.

adjustment together with a rack gear and the component on which the condenser holder is mounted.

Note - this module DOES NOT FIT Carl Zeiss Jena Nf and Carl Zeiss Jena Lu microscopes, even though the assemblies performing the same function in those microscopes look VERY similar.

In the last photos in the gallery, I use arrows to show exactly which microscope component is being offered and where it is located in the Carl Zeiss Jena NU-2 microscope.

Description of this part for the microscope.

2

this module serves as the aperture diaphragm. The field diaphragm is built into the illumination path inside the microscope base.

At the same time, it provides a holder for 32 mm round filters. The video available in the gallery also demonstrates how a filter is inserted into this holder.

The sliding iris diaphragm mounted beneath the microscope condenser allows oblique illumination to be set, producing a three-dimensional image with enhanced contrast of transparent specimens (such as unstained cells). The resulting image is similar to differential interference contrast (DIC).

This component is known under various names, including:
- decenterable iris diaphragm
- decentering aperture diaphragm
- off-axis iris diaphragm
- eccentric iris diaphragm
- sliding iris diaphragm
- sliding iris
- oblique illumination condenser
- condenser with sliding iris
- oblique illumination module
- oblique illumination diaphragm
- offset iris
- Poor Man's DIC device

Note - this diaphragm DOES NOT FIT the Carl Zeiss Jena Lumipan microscope, even though it appears very similar at first glance.

Because this module is removable, it is missing from a large proportion of microscopes available on the second-hand market. During decades of use, these diaphragm modules were frequently lost.

In addition, they are often damaged and need replacement. The most common failures include:
- the protective glass covering the diaphragm becomes scratched or broken
- the diaphragm blades become bent or broken
- the screw used to decenter the diaphragm bends or breaks
- the return spring responsible for restoring the diaphragm to its centred position becomes damaged or is missing

Replacing the damaged assembly with the diaphragm module offered here solves these problems.

Description of this part for the microscope.

Zeiss Jena
Model: Apl 1.4
Holder name according to the manufacturer's catalogue: Kondensor-Einhänger mo
Condenser name according to the manufacturer's catalogue: Aplanatischer Kondensor 1.4 mo / ms
Version: grey version from a Carl Zeiss Jena Ergaval microscope (as opposed to the black version used, for example, on Carl Zeiss Jena Nf microscopes)
Numerical aperture N.A.: 1.4
Aperture diaphragm: yes, mounted in the condenser holder
Wide-field lens: yes, swing-out type
Removable top lens: yes, unscrewable
Mounting diameter: the optical section (the condenser without the iris diaphragm) has a mounting diameter of 39.5 mm and can be unscrewed from the condenser holder

The complete assembly consists of the following components:
- upper Apl 1.4 lens
- removable condenser (mo / ms)
- iris diaphragm attached to the condenser holder
- condenser holder mo
- swing-out wide-field lens
- two centring screws

The last photograph in the gallery shows a page from the manufacturer's original catalogue. Arrows indicate both this exact condenser holder model and the matching condenser.

Mechanically, this condenser is mounted using a dovetail guide located beneath the microscope stage. On the Carl Zeiss Jena Ergaval this is a separate condenser mounting assembly, while on the Carl Zeiss Jena Amplival the dovetail is integrated into the microscope stage support assembly.

Description of this part for the microscope.

unscrewed. It is mounted onto the dovetail guide located underneath the microscope stage carrier and secured with a clamping screw.

Carl Zeiss Jena Ergaval microscopes were originally equipped with a condenser attached to the "MO" holder. This holder has a permanently mounted iris diaphragm and wide-field lens, while the condenser itself is screwed into the upper thread. In this configuration, the condenser cannot be exchanged.
The Carl Zeiss Jena Fluoval uses a similar arrangement, whereas the Carl Zeiss Jena Amplival was originally equipped with a panchromatic condenser.

If the user wishes to use other condensers (including those made by manufacturers other than Carl Zeiss Jena), the original condenser holder must be replaced with the MZ condenser holder. Once this has been done, any microscope condenser with a mounting diameter of 39.5 mm can be installed. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

This is exactly such a holder for interchangeable condensers.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: grey, the version manufactured for the Mikroval microscope series
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this component is grey, it is also compatible with older black Carl Zeiss Jena microscopes from the 1950s and 1960s (it simply will not look completely original unless it is repainted).

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of condenser holder, making it easy to identify the component.

Description of this part for the microscope.

unscrewed. It is mounted onto a dovetail guide located underneath the microscope stage carrier. The condenser holder is secured to the guide with a clamping screw.

It can accommodate any microscope condenser with a mounting diameter of 39.5 mm, regardless of the manufacturer. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: black, the version manufactured for the black Carl Zeiss Jena microscopes from the 1950s and 1960s
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this microscope component is black, it is also compatible with the newer grey Carl Zeiss Jena microscopes of the Mikroval series.

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of the condenser holder, making it easy to identify the component.

Description of this part for the microscope.

diameter: 23.2 mm

This eyepiece allows the microscope image to be projected onto a surface such as a wall, ceiling or projection screen.

Originally, this eyepiece model was supplied with the Carl Zeiss Jena Pictoval projection microscope. It can also be installed on virtually any microscope from any manufacturer with a 23.2 mm eyepiece tube.

Important: Projecting a microscope image requires a very large amount of light, so a high-power illuminator is necessary.

Description of this part for the microscope.

head in Carl Zeiss Jena Pictoval projection microscopes (microprojectors). The adjustable tilt angle of the eyepiece tube, which held a projection eyepiece (usually f=100), allowed the position of the projected image on the projection surface to be changed.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Eyepiece mounting diameter: 23.2 mm
Mounting to the microscope arm: 41 mm diameter dovetail ring

Because this microscope head has a Carl Zeiss Jena standard microscope mount (a 41 mm diameter dovetail ring), it can be mounted on most microscopes from this manufacturer (e.g. Carl Zeiss Jena Eduval, Laboval, Ergaval, Amplival, etc.), as well as on microscopes made by Lomo (e.g. Lomo Biolam), IOR and Meopta.

It seems useful to mention a few points:
- never look through this microscope head with the naked eye if a projection eyepiece is installed in it and the head is mounted in a Carl Zeiss Jena Pictoval microprojector. This may result in loss of eyesight due to the very high light output emitted by this microscope
- when mounting this microscope head on a microscope other than a Carl Zeiss Jena Pictoval, a different magnification scale may be obtained than with the original heads designed for the particular microscope model
- projecting a microscope image requires a great deal of light, i.e. a powerful illuminator. This is worth remembering if you intend to use this head to project an image from biological microscopes with standard incandescent illumination (e.g. 15 W 6 V), which is definitely not sufficient
- visual observation using this microscope head may be inconvenient because it has a different (smaller) tilt angle than standard monocular or binocular microscope heads

Description of this part for the microscope.

meters:
Manufacturer: Carl Zeiss Jena
Designation: Apl. 1,4
Name of the mount according to the manufacturer's catalogue: Kondensoreinhänger mfl 2, Bestellnummer 301080:021.26/0
Name of the condenser according to the manufacturer's catalogue: Aplanatischer Kondensor 1.4 mo / ms (applies only to the upper optical part)
Name of the condenser according to the manufacturer's catalogue: Kondensor hoher Lichtstärke mit Vorschaltsystem (applies to the entire module)
Version: grey colour with a black upper lens. Variant with a "dot" in the name after "Apl"
Numerical aperture N.A.: 1.4
Aperture diaphragm: yes, attached to the condenser mount
Wide-field lens: yes, it can be swung out of the optical path. This is the version with the large lens in a housing (see description below)
Removable upper lens: yes, it can be rotated
Mounting diameter: the optical part (condenser without diaphragm) has a mounting diameter of 39.5 mm and can be unscrewed from the condenser mount
Operating modes: the condenser can be used both as a dry condenser and as an immersion condenser

The entire part consists of the following elements:
- upper Apl. 1,4 lens
- screw-on/removable condenser (mo / ms)
- iris diaphragm screwed onto the condenser mount
- condenser mount model mfl 2
- swing-out wide-field lens
- two centering screws

This condenser is mainly used in Carl Zeiss Jena Fluoval / Fluoval-2 fluorescence microscopes. It is optimal for use with high-numerical-aperture apochromatic microscope objectives. For precisely this reason, users often install it on Carl Zeiss Jena Ergaval and Carl Zeiss Jena Amplival microscopes equipped with apochromatic objectives (Carl Zeiss Jena Apochromat).

It is worth mentioning again that this condenser can be used in two modes:
- without immersion oil on the upper lens of the condenser. In this case, it operates as a "dry condenser" and its numerical aperture N.A. is 0.9.
- with immersion oil on the upper lens of the condenser (i.e. underneath the microscope slide). In this case, it operates as an "immersion condenser" and its numerical aperture N.A. is 1.4, allowing a very bright image to be obtained - this is important in fluorescence microscopy or when using high-N.A. immersion objectives.

During production, this condenser was available in several versions:
- with a black upper lens, a dot in the model name (Apl. 1,4) and a wide-field module consisting of a single lens
- with a black upper lens, without a dot in the model name (Apl 1,4) and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a wide-field module consisting of two independently swing-out lenses, each on its own mount

I have not found any information anywhere as to whether the above-mentioned versions differ in their operation. From experience, I know that they are used interchangeably - but I do not know whether any differences in operation can actually be noticed.

Mechanically, this condenser is mounted on dovetail rails located underneath the microscope stage. In Carl Zeiss Jena Ergaval microscopes, this is a separate condenser mounting block, whereas in Carl Zeiss Jena Fluoval / Amplival microscopes, the dovetail is located on the microscope stage holder block.

The manufacturer describes this condenser as follows: "High-intensity condenser with an auxiliary system for illuminating large fields while imaging the field diaphragm. [...] The condenser of the FLUOVAL 2 can be used as a dry and immersion condenser of the highest aperture to achieve the highest possible excitation intensity. It is equipped with a switchable wide-field system that illuminates the large fields of low-power objectives while providing a sharp image of the field diaphragm in the object plane."

Description of this part for the microscope.

meters:
Manufacturer: Carl Zeiss Jena
Designation: Apl. 1,4
Name of the mount according to the manufacturer's catalogue: Kondensoreinhänger mfl 2, Bestellnummer 301080:021.26/0
Name of the condenser according to the manufacturer's catalogue: Aplanatischer Kondensor 1.4 mo / ms (applies only to the upper optical part)
Name of the condenser according to the manufacturer's catalogue: Kondensor hoher Lichtstärke mit Vorschaltsystem (applies to the entire module)
Version: grey colour with a black upper lens. Variant without the "dot" in the name after "Apl"
Numerical aperture N.A.: 1.4
Aperture diaphragm: yes, attached to the condenser mount
Wide-field lens: yes, it can be swung out of the optical path. This is the version with the large lens in a housing (see description below)
Removable upper lens: yes, it can be rotated
Mounting diameter: the optical part (condenser without diaphragm) has a mounting diameter of 39.5 mm and can be unscrewed from the condenser mount
Operating modes: the condenser can be used both as a dry condenser and as an immersion condenser

The entire part consists of the following elements:
- upper Apl 1,4 lens
- screw-on/removable condenser (mo / ms)
- iris diaphragm screwed onto the condenser mount
- condenser mount model mfl 2
- swing-out wide-field lens
- two centering screws

This condenser is mainly used in Carl Zeiss Jena Fluoval / Fluoval-2 fluorescence microscopes. It is optimal for use with high-numerical-aperture apochromatic microscope objectives. For precisely this reason, users often install it on Carl Zeiss Jena Ergaval and Carl Zeiss Jena Amplival microscopes equipped with apochromatic objectives (Carl Zeiss Jena Apochromat).

It is worth mentioning again that this condenser can be used in two modes:
- without immersion oil on the upper lens of the condenser. In this case, it operates as a "dry condenser" and its numerical aperture N.A. is 0.9.
- with immersion oil on the upper lens of the condenser (i.e. underneath the microscope slide). In this case, it operates as an "immersion condenser" and its numerical aperture N.A. is 1.4, allowing a very bright image to be obtained - this is important in fluorescence microscopy or when using high-N.A. immersion objectives.

During production, this condenser was available in several versions:
- with a black upper lens, a dot in the model name (Apl. 1,4) and a wide-field module consisting of a single lens
- with a black upper lens, without a dot in the model name (Apl 1,4) and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a single wide-field module consisting of several lenses (including one with a very small diameter)
- with a grey upper lens marked Apl 1,4mo2 and a wide-field module consisting of two independently swing-out lenses, each on its own mount

I have not found any information anywhere as to whether the above-mentioned versions differ in their operation. From experience, I know that they are used interchangeably - but I do not know whether any differences in operation can actually be noticed.

Mechanically, this condenser is mounted on dovetail rails located underneath the microscope stage. In Carl Zeiss Jena Ergaval microscopes, this is a separate condenser mounting block, whereas in Carl Zeiss Jena Fluoval / Amplival microscopes, the dovetail is located on the microscope stage holder block.

The manufacturer describes this condenser as follows: "High-intensity condenser with an auxiliary system for illuminating large fields while imaging the field diaphragm. [...] The condenser of the FLUOVAL 2 can be used as a dry and immersion condenser of the highest aperture to achieve the highest possible excitation intensity. It is equipped with a switchable wide-field system that illuminates the large fields of low-power objectives while providing a sharp image of the field diaphragm in the object plane."

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

be attached to a trinocular head or directly to the microscope body, even when there is no trinocular head.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: grey
Tilt angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to the trinocular head or microscope body: ring with a dovetail
Dovetail diameter: 41 mm
Type of connection at the output: empty tube / barrel
Tube diameter at the output: 23.2 mm internal diameter
Length of the barrel / tube: 25 mm
Length adjustment: no - this is not a tube with adjustable height

Since the adapter has an empty barrel with an internal diameter of 23.2 mm on the output side, a projection eyepiece of that diameter can be placed in it, or a so-called "USB eyepiece", that is a digital microscope camera. Adapters between the 23.2 mm barrel and the M42 thread are also widely available, and from the M42 thread you can move on to any other mount: Nikon, Canon, Sony and others.

Such a tube can be mounted directly on the microscope body instead of the head. A dovetail seat with a diameter of 41.0 - 41.5 mm is found, among others, on the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH

It is also often used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can equally well be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol microscopes
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in the LOMO Polam microscopes
- some versions of the intermediate photo tubes for the Carl Zeiss Jena Mikroval series microscopes (others require a tube screwed onto a thread)

This is not a "tube for one specific microscope model". A trinocular head can be mounted not only on the microscope it was sold with - it is therefore correct to assume that this is a universal tube, with a 41 mm dovetail on one side and a 23.2 mm barrel on the other.

The "compatibility" section gives an example list of microscopes this tube fits, although it is not a complete list.

Description of this part for the microscope.

Carl Zeiss Jena
Engraving on the objective: Planachromat 25x/0,50 ∞/0
Magnification: 25x
Numerical aperture N.A.: 0,50
Free working distance: 3,1 mm
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: no - this objective has no phase ring inside
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective calls for eyepieces with additional correction (designated "PK" by Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography by connecting the objective directly to a camera

This objective can be used as:
- an objective for work in reflected light (EPI), for biological as well as, among others, metallurgical or mineralogical applications
- an objective for work in transmitted light, among others with biological specimens or, for example, with mineralogical thin sections

A few facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes of this company:
- these objectives serve mostly technical applications and are intended for work without a cover glass (marking ∞/0)
- CZJ M19 objectives intended for biological applications (that is, marked ∞/0,17) are most often used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with the EPI illuminator and can then work both in bright field and in dark field
- in Carl Zeiss Jena Polmi-A microscopes, CZJ M19 objectives can be used, but they give a magnification other than the nominal one
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes have an interchangeable nosepiece, and there is also a nosepiece intended for these microscopes that accepts objectives with M19 thread
- Carl Zeiss Jena Metaval microscopes use newer versions of CZJ M19 objectives (those with a coarsely knurled rim and a glossy barrel), yet many people experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various configurations - and some work with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow work with CZJ M19 objectives in EPI dark field mode
- on inverted metallographic Carl Zeiss Jena Epityp-2 / Neophot-21 microscopes, many people use biological objectives intended for work with a cover glass alongside metallurgical ones, and place the slide with the specimen on the stage "upside down", that is, with the cover glass facing downwards

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 25x/0,50 ∞/0 Ph
Magnification: 25x
Numerical aperture N.A.: 0,50
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) is the same objective in the version without phase rings. Its description tells you more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 12.5x/0.25 ∞/0 Ph
Magnification: 12.5x
Numerical aperture N.A.: 0.25
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) you can read more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 6.3x/0.12 ∞/0 Ph
Magnification: 6.3x
Numerical aperture N.A.: 0.12
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) you can read more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

camera to a trinocular head or directly to the microscope stand, even when there is no trinocular head at all.

This is a black tube with an upper element (barrel) 55 mm long. Here (https://www.microscopeparts.eu/gallery/91057) you can see a functionally identical adapter, but grey and with an upper barrel only 25 mm long.

Black adapters of this kind come from the era of the Carl Zeiss Jena L stands (models Carl Zeiss Jena Lg, Lumipan, Ng, Nf or Nu). The grey ones are newer, from the era of the Mikroval series (models Carl Zeiss Jena Laboval, Eduval, Ergaval or Amplival and Docuval).

The mounting fit is of course identical, so both can be used interchangeably.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: black
Inclination angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to a trinocular head or microscope stand: ring dovetail
Ring dovetail diameter: 41.5 mm
Type of connection at the output: empty barrel / tube
Tube diameter at the output: 23.2 mm inner diameter
Barrel / tube length: 55 mm
Tube length adjustment: no - this is not a height-adjustable tube

Because on the output side this adapter has an empty barrel with an inner diameter of 23.2 mm, you can place in it a projection eyepiece of that diameter or a so-called USB eyepiece, that is a digital microscope camera. In addition, adapters between the 23.2 mm barrel and the M42 thread are widely available, and from the M42 thread you can already move on to any other mount: Nikon, Canon, Sony and all the rest.

Such a tube can be mounted directly on the microscope stand, in place of the head. A seat for a ring dovetail of 41.0 - 41.5 mm diameter is found among others in the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH
- Gamma

It is also used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can likewise be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the microscopes Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in LOMO Polam microscopes
- some versions of the black intermediate photo tubes for the microscopes Carl Zeiss Jena Lg / Lumipan / Nf and of the grey ones from the Mikroval series (others require a tube that screws in on a thread)

This is not a tube for one particular microscope model. A trinocular head can be mounted not only on the microscope it was sold with, so the correct assumption is that this is a universal tube with a ring dovetail of 41.5 mm diameter on one side and a barrel of 23.2 mm diameter on the other.

In the compatibility section you will find an example list of microscopes this tube fits, although that list is not complete.

Description of this part for the microscope.

Jena
Inscription: logo "Carl Zeiss Jena" and text "Q1 MADE IN DDR"
Material: aluminium
Length: 52 mm
Width: 14 mm
Mounting: the nameplate is glued on

By default such a nameplate was fitted to most Carl Zeiss Jena microscopes from the Mikroval series onwards. There is also a smaller nameplate - with the manufacturer logo only (without the "Q1 Made in DDR" text). You can see it here: https://www.microscopeparts.eu/part/00604.

Because the adhesive used to attach these plates to the microscope body loses its properties over the years, these plates very often fall off. A nameplate like this makes it possible to restore the factory appearance of a microscope using original parts.

Description of this part for the microscope.

Carl Zeiss Jena NU microscope (this socket carries the number 44 in the instruction manual). It measures the brightness of the image, from which the exposure time for photographs is determined.

The instruction manual for the Carl Zeiss Jena NU microscope is made available by the excellent site mikroskop-online.de here: https://www.mikroskop-online.de/mikroskope/wp-content/uploads/simple-file-list/Mikroskop-Bedienanleitungen-Druckschriften-Carl-Zeiss-Jena-Mikroskopen/30-040-1_G-Grosses-Universal-Forschungsmikroskop-NU-T.pdf