Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Coarse focus element.

Description of this part for the microscope.

microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Coarse focus element.

Description of this part for the microscope.

microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Coarse focus element.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Mikroval series:
- Eduval
- Laboval
- Ergaval
- Amplival (the entire series, including Epival, Vertival, Amplival-Pol)
- Fluoval
- Metaval
- Telaval
- and even Epignost

Description of this part for the microscope.

Jena's Mikroval series microscopes:
- Eduval
- Laboval
- Ergaval
- Amplival (the entire series, including Epival, Vertival, Amplival-Pol)
- Fluoval
- Metaval
- Telaval
- and even Epignost

Description of this part for the microscope.

transmitted or reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Model: D42 15x
Magnification: 15x
Image: micrometer and X-crosshair
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Identical K15x eyepieces were also made by other manufacturers, such as Lomo and PZO.

Description of this part for the microscope.

screw also fits microscope stages with the handle pointing down, which were used in microscopes:
- Carl Zeiss Jena Amplival / Metaval (long handle)
- Carl Zeiss Jena Ergaval (short handle).

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

6x
Angle: 30°

Other names for this part:
- intermediate tube
- mirror tube

Description of this part for the microscope.

Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena NU-2

There are several models of mechanical microscope stages from Carl Zeiss Jena designed for microscopes of the Mikroval series. They differ mainly in the placement of the control knobs used for movement in both axes, for example:
- the Ergaval model has a short handle with control knobs
- the Amplival model has a long handle
- some variants of the Laboval model had a stage without a handle with control knobs, where the knobs were arranged horizontally on both sides of the stage.

However, many of the individual components used in these stages are identical.

Many of these stages can also be used interchangeably with other microscopes of the Vertival series, which means that many microscopes today no longer have their original stages. For this reason it is best to examine the photos carefully to make sure that the element shown and offered here will fit.

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena NU-2

There are several models of mechanical microscope stages from Carl Zeiss Jena designed for microscopes of the Mikroval series. They differ mainly in the placement of the control knobs used for movement in both axes, for example:
- the Ergaval model has a short handle with control knobs
- the Amplival model has a long handle
- some variants of the Laboval model had a stage without a handle with control knobs, where the knobs were arranged horizontally on both sides of the stage.

However, many of the individual components used in these stages are identical.

Many of these stages can also be used interchangeably with other microscopes of the Vertival series, which means that many microscopes today no longer have their original stages. For this reason it is best to examine the photos carefully to make sure that the element shown and offered here will fit.

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena NU-2

There are several models of mechanical microscope stages from Carl Zeiss Jena designed for microscopes of the Mikroval series. They differ mainly in the placement of the control knobs used for movement in both axes, for example:
- the Ergaval model has a short handle with control knobs
- the Amplival model has a long handle
- some variants of the Laboval model had a stage without a handle with control knobs, where the knobs were arranged horizontally on both sides of the stage.

However, many of the individual components used in these stages are identical.

Many of these stages can also be used interchangeably with other microscopes of the Vertival series, which means that many microscopes today no longer have their original stages. For this reason it is best to examine the photos carefully to make sure that the element shown and offered here will fit.

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

probably fits most Carl Zeiss Jena microscope stages models

In the photo gallery there are detailed photos of this element together with the dimensions. Thanks to this it is possible to identify exactly which part of the microscope stage it is.

Description of this part for the microscope.

Zeiss Jena produced two very similar microscope stage models - one with a long manipulator (used, for example, in Amplival microscopes) and the other with a short manipulator (used, for example, in Ergaval microscopes). This element fits the models with the long manipulator (long handle).

In the photo gallery there are detailed photos of this element together with the dimensions. Thanks to this it is possible to identify exactly which part of the microscope stage it is.

Description of this part for the microscope.

Zeiss Jena produced two very similar microscope stage models - one with a long manipulator (used, for example, in Amplival microscopes) and the other with a short manipulator (used, for example, in Ergaval microscopes). This element fits the models with the long manipulator (long handle).

In the photo gallery there are detailed photos of this element together with the dimensions. Thanks to this it is possible to identify exactly which part of the microscope stage it is.

Description of this part for the microscope.

screw also fits microscope cross-stage attachments used in microscopes such as:
- Carl Zeiss Jena Laboval
- Carl Zeiss Jena Eduval

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

Zeiss Jena produced two very similar microscope stage models - one with a long manipulator (used, for example, in Amplival microscopes) and the other with a short manipulator (used, for example, in Ergaval microscopes). This element fits the models with the long manipulator (long handle).

In the photo gallery there are detailed photos of this element together with the dimensions. Thanks to this it is possible to identify exactly which part of the microscope stage it is.

Description of this part for the microscope.

Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena NU-2

There are several models of mechanical microscope stages from Carl Zeiss Jena designed for microscopes of the Mikroval series. They differ mainly in the placement of the control knobs used for movement in both axes, for example:
- the Ergaval model has a short handle with control knobs
- the Amplival model has a long handle
- some variants of the Laboval model had a stage without a handle with control knobs, where the knobs were arranged horizontally on both sides of the stage.

However, many of the individual components used in these stages are identical.

Many of these stages can also be used interchangeably with other microscopes of the Mikroval series, which means that many microscopes today no longer have their original stages. For this reason it is best to examine the photos carefully to make sure that the element shown and offered here will fit.

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena NU-2

There are several models of mechanical microscope stages from Carl Zeiss Jena designed for microscopes of the Mikroval series. They differ mainly in the placement of the control knobs used for movement in both axes, for example:
- the Ergaval model has a short handle with control knobs
- the Amplival model has a long handle
- some variants of the Laboval model had a stage without a handle with control knobs, where the knobs were arranged horizontally on both sides of the stage.

However, many of the individual components used in these stages are identical.

Many of these stages can also be used interchangeably with other microscopes of the Mikroval series, which means that many microscopes today no longer have their original stages. For this reason it is best to examine the photos carefully to make sure that the element shown and offered here will fit.

The surface of these microscope stages is often very worn. You could try painting it, but it's definitely better to replace it. The piece I'm showing here isn't perfect - it shows signs of wear, but it's in very good condition.

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena NU-2

There are several models of mechanical microscope stages from Carl Zeiss Jena designed for microscopes of the Mikroval series. They differ mainly in the placement of the control knobs used for movement in both axes, for example:
- the Ergaval model has a short handle with control knobs
- the Amplival model has a long handle
- some variants of the Laboval model had a stage without a handle with control knobs, where the knobs were arranged horizontally on both sides of the stage.

However, many of the individual components used in these stages are identical.

Many of these stages can also be used interchangeably with other microscopes of the Mikroval series, which means that many microscopes today no longer have their original stages. For this reason it is best to examine the photos carefully to make sure that the element shown and offered here will fit.

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena NU-2

There are several models of mechanical microscope stages from Carl Zeiss Jena designed for microscopes of the Mikroval series. They differ mainly in the placement of the control knobs used for movement in both axes, for example:
- the Ergaval model has a short handle with control knobs
- the Amplival model has a long handle
- some variants of the Laboval model had a stage without a handle with control knobs, where the knobs were arranged horizontally on both sides of the stage.

However, many of the individual components used in these stages are identical.

Many of these stages can also be used interchangeably with other microscopes of the Mikroval series, which means that many microscopes today no longer have their original stages. For this reason it is best to examine the photos carefully to make sure that the element shown and offered here will fit.

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: micrometer
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: none
Mounting diameter: 23.2 mm

There is no measuring scale glass inside the eyepiece. Any 19mm diameter glass can be inserted inside, for example, with a crosshair, micrometer, or reticle.

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

used, for example, in microscopes from Carl Zeiss Jena of the Mikroval series:
- Eduval
- Laboval
- Ergaval
- Amplival (entire series including Epival, Vertival, Amplival-Pol)
- Fluoval
- Metaval
- Telaval
- even Epignost

In microscope models with fluorescence illumination (e.g. Laboval Fluoreszenz or Fluoval), a filter wheel is installed in this head. When the manufacturer installed this head in other microscope models - a blanking plug was placed instead of the filter wheel - and this is exactly the element shown here.

Over the years, this element is very often lost and on the secondary market there are many such photo trino adapters without the blanking plug. The lack of this blanking plug can cause even large contaminants to enter the optics.

Description of this part for the microscope.

(and its variants: Fluoval, Epival, Vertival)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

Both the left and the right knob are identical, but when installing be careful about the screw length, as they may differ).

VERY IMPORTANT: although the right and left knobs are identical - different screws are used to attach them.

Lengths of screws used to attach the knobs in Carl Zeiss Jena Ergaval and Amplival microscopes:
- left fine adjustment knob (micro): 1 pc. screw 12 mm
- left coarse adjustment knob (macro): 3 pcs. screws 8 mm
- right fine adjustment knob (micro): 1 pc. screw 16 mm
- right coarse adjustment knob (macro): 3 pcs. screws 12 mm

Over the years these plastic knobs are often damaged:
- sometimes they crack due to impact or improper transport securing
- often they are partially melted by a soldering iron, light bulb or even a cigarette
- sometimes they are damaged during attempts to remove them

Description of this part for the microscope.

Amplival (and its variants: Fluoval, Epival, Vertival)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

Both the left and the right knob are identical, but when installing be careful about the screw length, as they may differ).

VERY IMPORTANT: although the right and left knobs are identical - different screws are used to attach them.

Lengths of screws used to attach the knobs in Carl Zeiss Jena Ergaval and Amplival microscopes:
- left fine adjustment knob (micro): 1 pc. screw 12 mm
- left coarse adjustment knob (macro): 3 pcs. screws 8 mm
- right fine adjustment knob (micro): 1 pc. screw 16 mm
- right coarse adjustment knob (macro): 3 pcs. screws 12 mm

Over the years these plastic knobs are often damaged:
- sometimes they crack due to impact or improper transport securing
- often they are partially melted by a soldering iron, light bulb or even a cigarette
- sometimes they are damaged during attempts to remove them
- sometimes, when the grease has dried out, the user tries to move the knob using pliers and damages it

Description of this part for the microscope.

Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the left clamp, which does have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

microscopes:
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the right clamp, which does have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the left clamp, simple, which does NOT have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

meaning the shaft with focusing knobs mounted on both ends on the sides of the microscope. Part of this shaft contains a toothed rack, or more precisely speaking, it is a toothed shaft. In the item shown and offered here, the fine focus knob (micro focus) is mounted on the left end of the shaft. Please note that the left and right knobs are identical - however, screws of different lengths are used to attach them: the left knob is attached with a 12 mm screw, while the right knob uses a 16 mm screw. Detailed information about the screws used to attach the coarse and fine focus knobs can be found here: https://www.facebook.com/MikroskopyPZO/posts/pfbid0x2tFPHAEqjn4B7BRsvm2vAt9yyuuSM836QS6K4951GqeUFpU2FJH8YXfFFxbz3cPl

Such focus shafts are used in the following microscopes:
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival (and its variants: Fluoval, Epival, Vertival, Interphako)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

This coarse and fine focus shaft may help solve the following problems in Carl Zeiss Jena Ergaval / Amplival microscopes and related models:
- if the shaft became bent, causing a noticeable jump while rotating it (a very common failure)
- if the screw holding the fine focus knob broke off or snapped, leaving part of the screw inside the shaft
- if the left fine focus knob is missing or damaged
- if the thread on the right or left end of the shaft, where the fine focus knobs are attached, is damaged
- if the toothed rack on the shaft (because such a shaft is effectively a toothed shaft) becomes damaged

Description of this part for the microscope.

for taking microscope photographs or recording microscope videos. This is a gray photographic adapter.

Basic technical parameters:
- mounting connection to microscope stand: 41 mm dovetail
- output connection type on the photo port: 49 mm internal thread
- connection for binocular head mounting: Jena standard 41 mm dovetail
- magnification directed to the binocular head: 1.6x
- magnification on the photo output: none (that is 1.0x)

Because this photo head has a 49 mm threaded output, virtually any device, camera, adapter, tube or other accessory can be connected after using an appropriate 49 mm thread adapter. Direct projection technique may be used (because there is no additional optics inside), or any projection eyepieces may be installed in the optical path.

This photographic attachment is intended mainly (but not exclusively) for the following microscope models:
- Carl Zeiss Jena Eduval
- Carl Zeiss Jena Laboval
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Telaval
- Carl Zeiss Jena Pictoval
- Carl Zeiss Jena Epignost

The list above contains Mikroval series microscopes with gray housings - just like the tube shown and offered here. However, it also works with older black Carl Zeiss Jena microscopes:
- Carl Zeiss Jena L-Stativ (models Lg, Lu and Lr)
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Ng
- Carl Zeiss Jena Nf (and NfPk)

Please note that microscopes from other manufacturers also use the 41 / 41.5 mm dovetail connection standard. Because of this, this photographic head can also be used with microscopes made by:
- Lomo (for example Lomo Biolam)
- Meopta
- IOR
- selected Reichert microscopes (for example Reichert Neozet)
- Will Wetzlar
- Hund Wetzlar
- Leitz Wetzlar

This Carl Zeiss Jena tube is also very often used with microscopes having a larger head mounting diameter. In such cases users apply additional spacer or thickening rings. Because of this, this photo adapter also fits microscopes from manufacturers such as:
- PZO (for example the PZO Biolar model with 43 mm connection)
- Olympus (for example the Olympus CH model with 42 mm connection)

The element that allows a photographic camera or imaging camera to be connected to Carl Zeiss Jena Mikroval series microscopes may be referred to by different names. Commonly used names include:
- trino head
- trinocular head
- photo head
- photographic head
- photo attachment
- photographic attachment
- photo adapter
- photographic adapter
- photo tube
- photographic tube
- phototube
- photographic angle tube
- and various combinations of the words head, attachment, adapter or tube with terms such as photo, photographic, for camera and similar

Description of this part for the microscope.

microscope objective
- Manufacturer: Carl Zeiss Jena
- Designation: Planachromat 25x/0,50 oo/0,17
- Magnification: 25x
- Numerical aperture N.A.: 0,50
- Optical correction: infinity-corrected tube length
- Optical correction class: planachromat
- Cover glass: yes, 0.17 mm
- Thread: M19

Some facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes from this manufacturer:
- these objectives are most commonly used for technical applications rather than biological applications, therefore most objectives available on the secondary market are intended for use without a cover glass (designation oo/0)
- CZJ M19 objectives intended for biological applications (designation oo/0,17) are most commonly used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with an EPI illuminator
- CZJ M19 objectives can be used in Carl Zeiss Jena Polmi-A microscopes, but they provide a different magnification than the nominal value
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes feature interchangeable nosepieces, and a dedicated nosepiece for M19-thread objectives was also produced for these microscopes
- Carl Zeiss Jena Metaval and Neophot microscopes use newer versions of CZJ M19 objectives (with a coarse-knurled edge and shiny housing), although many users still experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various versions with completely different configurations - and some of them operate with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow the use of CZJ M19 objectives in EPI dark-field mode
- on the Carl Zeiss Jena Epityp-2 inverted metallurgical microscope, many users employ biological objectives designed for use with a cover glass, placing the microscope slide "upside down", with the cover glass facing downward toward the objective.

Description of this part for the microscope.

in the microscope.

As far as I know, the same mechanism is used in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval
- Peraval

This component is installed onto the shaft by sliding the internal tab into the keyway groove on the shaft. After tightening the round slotted nut, a locking mechanism is created that prevents the nut from loosening on its own due to vibration.

Instructions for disassembling the fine- and coarse focus mechanism in a Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

movement in the microscope.

As far as I know, the same mechanism is used in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval
- Peraval

This component acts as a resistance regulator and functions as a friction brake. Tightening the outer element compresses the tapered section of the bushing, causing the slotted bushing to contract at the slit. This increases friction on the shaft and makes the entire mechanism move with greater resistance.

Note - in some descriptions available on the Internet, this component is referred to as a "piece of wood".

Instructions for disassembling the coarse focus and fine focus mechanism in a Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

unscrewed. It is mounted onto the dovetail guide located underneath the microscope stage carrier and secured with a clamping screw.

Carl Zeiss Jena Ergaval microscopes were originally equipped with a condenser attached to the "MO" holder. This holder has a permanently mounted iris diaphragm and wide-field lens, while the condenser itself is screwed into the upper thread. In this configuration, the condenser cannot be exchanged.
The Carl Zeiss Jena Fluoval uses a similar arrangement, whereas the Carl Zeiss Jena Amplival was originally equipped with a panchromatic condenser.

If the user wishes to use other condensers (including those made by manufacturers other than Carl Zeiss Jena), the original condenser holder must be replaced with the MZ condenser holder. Once this has been done, any microscope condenser with a mounting diameter of 39.5 mm can be installed. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

This is exactly such a holder for interchangeable condensers.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: grey, the version manufactured for the Mikroval microscope series
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this component is grey, it is also compatible with older black Carl Zeiss Jena microscopes from the 1950s and 1960s (it simply will not look completely original unless it is repainted).

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of condenser holder, making it easy to identify the component.

Description of this part for the microscope.

unscrewed. It is mounted onto a dovetail guide located underneath the microscope stage carrier. The condenser holder is secured to the guide with a clamping screw.

It can accommodate any microscope condenser with a mounting diameter of 39.5 mm, regardless of the manufacturer. Condensers with a 37 mm mounting diameter can also be used if they are fitted with a suitable adapter ring.

Basic specifications:
Manufacturer: Carl Zeiss Jena
Original documentation name and model: Kondensor-Einhänger MZ
Colour: black, the version manufactured for the black Carl Zeiss Jena microscopes from the 1950s and 1960s
Internal diameter: for mounting condensers with a 39.5 mm mounting diameter (for example the Carl Zeiss Jena cardioid darkfield condenser)
Condenser retaining screw: yes, central condenser clamping screw
Centering screws: yes, two condenser centering screws
Microscope mounting: dovetail

Although this microscope component is black, it is also compatible with the newer grey Carl Zeiss Jena microscopes of the Mikroval series.

This condenser holder is compatible with, among others:
- Carl Zeiss Jena Ng (black microscope)
- Carl Zeiss Jena Polmi-A (black microscope)
- Carl Zeiss Jena Nf (black microscope)
- Carl Zeiss Jena Nu (the NU-2 version is grey)
- Carl Zeiss Jena Ergaval (grey microscope)
- Carl Zeiss Jena Fluoval / Fluoval-2 (grey microscope)
- Carl Zeiss Jena Amplival and its variants (grey microscope)
- Carl Zeiss Jena Docuval (grey microscope)

Various names are used for this microscope component, including:
- condenser holder
- condenser carrier
- condenser mount
- condenser support

The last photograph includes an excerpt from the original manufacturer's documentation. An arrow indicates this exact model of the condenser holder, making it easy to identify the component.

Description of this part for the microscope.

diameter: 23.2 mm

This eyepiece allows the microscope image to be projected onto a surface such as a wall, ceiling or projection screen.

Originally, this eyepiece model was supplied with the Carl Zeiss Jena Pictoval projection microscope. It can also be installed on virtually any microscope from any manufacturer with a 23.2 mm eyepiece tube.

Important: Projecting a microscope image requires a very large amount of light, so a high-power illuminator is necessary.

Description of this part for the microscope.

head in Carl Zeiss Jena Pictoval projection microscopes (microprojectors). The adjustable tilt angle of the eyepiece tube, which held a projection eyepiece (usually f=100), allowed the position of the projected image on the projection surface to be changed.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Eyepiece mounting diameter: 23.2 mm
Mounting to the microscope arm: 41 mm diameter dovetail ring

Because this microscope head has a Carl Zeiss Jena standard microscope mount (a 41 mm diameter dovetail ring), it can be mounted on most microscopes from this manufacturer (e.g. Carl Zeiss Jena Eduval, Laboval, Ergaval, Amplival, etc.), as well as on microscopes made by Lomo (e.g. Lomo Biolam), IOR and Meopta.

It seems useful to mention a few points:
- never look through this microscope head with the naked eye if a projection eyepiece is installed in it and the head is mounted in a Carl Zeiss Jena Pictoval microprojector. This may result in loss of eyesight due to the very high light output emitted by this microscope
- when mounting this microscope head on a microscope other than a Carl Zeiss Jena Pictoval, a different magnification scale may be obtained than with the original heads designed for the particular microscope model
- projecting a microscope image requires a great deal of light, i.e. a powerful illuminator. This is worth remembering if you intend to use this head to project an image from biological microscopes with standard incandescent illumination (e.g. 15 W 6 V), which is definitely not sufficient
- visual observation using this microscope head may be inconvenient because it has a different (smaller) tilt angle than standard monocular or binocular microscope heads

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

be attached to a trinocular head or directly to the microscope body, even when there is no trinocular head.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: grey
Tilt angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to the trinocular head or microscope body: ring with a dovetail
Dovetail diameter: 41 mm
Type of connection at the output: empty tube / barrel
Tube diameter at the output: 23.2 mm internal diameter
Length of the barrel / tube: 25 mm
Length adjustment: no - this is not a tube with adjustable height

Since the adapter has an empty barrel with an internal diameter of 23.2 mm on the output side, a projection eyepiece of that diameter can be placed in it, or a so-called "USB eyepiece", that is a digital microscope camera. Adapters between the 23.2 mm barrel and the M42 thread are also widely available, and from the M42 thread you can move on to any other mount: Nikon, Canon, Sony and others.

Such a tube can be mounted directly on the microscope body instead of the head. A dovetail seat with a diameter of 41.0 - 41.5 mm is found, among others, on the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH

It is also often used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can equally well be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol microscopes
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in the LOMO Polam microscopes
- some versions of the intermediate photo tubes for the Carl Zeiss Jena Mikroval series microscopes (others require a tube screwed onto a thread)

This is not a "tube for one specific microscope model". A trinocular head can be mounted not only on the microscope it was sold with - it is therefore correct to assume that this is a universal tube, with a 41 mm dovetail on one side and a 23.2 mm barrel on the other.

The "compatibility" section gives an example list of microscopes this tube fits, although it is not a complete list.

Description of this part for the microscope.

Carl Zeiss Jena
Engraving on the objective: Planachromat 25x/0,50 ∞/0
Magnification: 25x
Numerical aperture N.A.: 0,50
Free working distance: 3,1 mm
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: no - this objective has no phase ring inside
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective calls for eyepieces with additional correction (designated "PK" by Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography by connecting the objective directly to a camera

This objective can be used as:
- an objective for work in reflected light (EPI), for biological as well as, among others, metallurgical or mineralogical applications
- an objective for work in transmitted light, among others with biological specimens or, for example, with mineralogical thin sections

A few facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes of this company:
- these objectives serve mostly technical applications and are intended for work without a cover glass (marking ∞/0)
- CZJ M19 objectives intended for biological applications (that is, marked ∞/0,17) are most often used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with the EPI illuminator and can then work both in bright field and in dark field
- in Carl Zeiss Jena Polmi-A microscopes, CZJ M19 objectives can be used, but they give a magnification other than the nominal one
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes have an interchangeable nosepiece, and there is also a nosepiece intended for these microscopes that accepts objectives with M19 thread
- Carl Zeiss Jena Metaval microscopes use newer versions of CZJ M19 objectives (those with a coarsely knurled rim and a glossy barrel), yet many people experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various configurations - and some work with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow work with CZJ M19 objectives in EPI dark field mode
- on inverted metallographic Carl Zeiss Jena Epityp-2 / Neophot-21 microscopes, many people use biological objectives intended for work with a cover glass alongside metallurgical ones, and place the slide with the specimen on the stage "upside down", that is, with the cover glass facing downwards

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 25x/0,50 ∞/0 Ph
Magnification: 25x
Numerical aperture N.A.: 0,50
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) is the same objective in the version without phase rings. Its description tells you more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 12.5x/0.25 ∞/0 Ph
Magnification: 12.5x
Numerical aperture N.A.: 0.25
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) you can read more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

21 microscope.

Basic parameters:
Manufacturer: Carl Zeiss Jena
Engraving on the objective: Planachromat 6.3x/0.12 ∞/0 Ph
Magnification: 6.3x
Numerical aperture N.A.: 0.12
Tube length: infinity (more precisely: 250 mm)
Optical correction: planachromatic
Cover glass: no - this objective is intended for work without a cover glass
Immersion: no - this is a so-called dry objective
Phase contrast: yes, a special phase contrast for work in reflected light
Polarisation: no - this is not a polarising objective
Thread: M19
Plan compensating eyepieces: yes, required - this objective needs eyepieces with additional correction (marked "PK" at Carl Zeiss Jena)
Direct projection and macro photography: no - this objective does not work in direct projection mode and is not suitable for macro photography with the objective attached directly to a camera

Phase contrast objectives for the Neophot microscopes have a phase ring built differently from the other Ph objectives made by Carl Zeiss Jena - instead of a continuous ring there is a three-segment pattern, somewhat reminiscent of a Wankel engine rotor. This is worth knowing, because it means that a phase contrast objective from a biological microscope will not replace this one in a Neophot, and the other way round.

The reason is a matter of design. In a metallurgical microscope the objective also acts as the condenser, so the illuminating light passes through the same pupil as the light forming the image. With a continuous ring the whole illumination would pass through the phase coating, which lets only part of the light through and reflects a fair amount of it - and those reflections would swamp the already faint phase contrast image. The solution turned out to be an odd number of segments: the image of the diaphragm formed after reflection off the specimen is rotated by 180 degrees, so with three segments it falls into the gaps between them. The illuminating light therefore enters beside the phase coating and returns through it. The solution is described in patent AT 295883 B.

The objective is offered together with its matching slider (Objektivwechselschlitten) with an M19 thread - and that is no coincidence. The position in which the phase sectors come to rest is decided by how far the objective screws into the thread, and every specimen stops slightly differently, which is why the factory selected objective and slider in pairs and wrote both numbers on the card in the case. Buying such a pair together avoids the whole problem - the objective already sits in relation to its slider exactly as it left the works.

Setting it up in the microscope needs neither a service technician nor a phase telescope - the Neophot has a built-in, swing-out Bertrand lens. The procedure is basically this: switch in the Bertrand lens, focus on the phase sectors and use the adjusting screws to bring the image of the sector diaphragm into coincidence with the image of the sectors in the objective; sometimes a slight rotation of the aperture diaphragm helps as well. Should the position of the glass in the sector diaphragm itself ever need correcting - it is held down by an ordinary threaded ring, so it can be turned. The whole thing resembles centring the phase rings in the condenser of a biological microscope.

Two more things are needed on the microscope side for work in phase contrast: the sector diaphragm (Sektorenblende), pushed in front of the open aperture diaphragm, and the auxiliary lens turret (Hilfslinsenrevolver) on the dovetail of the illuminator. The latter images the diaphragm exactly in the plane of the phase coating, which lies slightly differently in each objective - hence a separate auxiliary lens for every magnification. In bright field the objective of course works perfectly normally.

A note for the DIY-minded: an objective like this can be adapted for transmitted light, except that the diaphragm in the condenser is then set not opposite but in line with the segments of the objective, because there is no second pass through the pupil. Phase contrast should appear, but with stronger halo and a directional relief effect, since the gaps in the ring mean that part of the illumination azimuths is missing. On top of that comes the infinity design with no cover glass correction, so a tube lens will be needed. More of an experiment than a working solution - but doable in one evening.

The last photos in the gallery show:

* a photo of the original table indicating which serial numbers of the objective sliders are factory-paired with which serial numbers of the objectives
* two pages of errata to the instruction manual of the Carl Zeiss Jena Neophot 2 microscope.

The "compatibility" section lists, besides the Carl Zeiss Jena Neophot 21 microscope, those microscopes that this objective fits mechanically and optically. What result you get on them, however, can sometimes be a surprise.

Here (https://www.microscopeparts.eu/part/91056) you can read more about using Carl Zeiss Jena objectives with an M19 thread.

Description of this part for the microscope.

camera to a trinocular head or directly to the microscope stand, even when there is no trinocular head at all.

This is a black tube with an upper element (barrel) 55 mm long. Here (https://www.microscopeparts.eu/gallery/91057) you can see a functionally identical adapter, but grey and with an upper barrel only 25 mm long.

Black adapters of this kind come from the era of the Carl Zeiss Jena L stands (models Carl Zeiss Jena Lg, Lumipan, Ng, Nf or Nu). The grey ones are newer, from the era of the Mikroval series (models Carl Zeiss Jena Laboval, Eduval, Ergaval or Amplival and Docuval).

The mounting fit is of course identical, so both can be used interchangeably.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: black
Inclination angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to a trinocular head or microscope stand: ring dovetail
Ring dovetail diameter: 41.5 mm
Type of connection at the output: empty barrel / tube
Tube diameter at the output: 23.2 mm inner diameter
Barrel / tube length: 55 mm
Tube length adjustment: no - this is not a height-adjustable tube

Because on the output side this adapter has an empty barrel with an inner diameter of 23.2 mm, you can place in it a projection eyepiece of that diameter or a so-called USB eyepiece, that is a digital microscope camera. In addition, adapters between the 23.2 mm barrel and the M42 thread are widely available, and from the M42 thread you can already move on to any other mount: Nikon, Canon, Sony and all the rest.

Such a tube can be mounted directly on the microscope stand, in place of the head. A seat for a ring dovetail of 41.0 - 41.5 mm diameter is found among others in the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH
- Gamma

It is also used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can likewise be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the microscopes Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in LOMO Polam microscopes
- some versions of the black intermediate photo tubes for the microscopes Carl Zeiss Jena Lg / Lumipan / Nf and of the grey ones from the Mikroval series (others require a tube that screws in on a thread)

This is not a tube for one particular microscope model. A trinocular head can be mounted not only on the microscope it was sold with, so the correct assumption is that this is a universal tube with a ring dovetail of 41.5 mm diameter on one side and a barrel of 23.2 mm diameter on the other.

In the compatibility section you will find an example list of microscopes this tube fits, although that list is not complete.

Description of this part for the microscope.

Jena
Inscription: logo "Carl Zeiss Jena" and text "Q1 MADE IN DDR"
Material: aluminium
Length: 52 mm
Width: 14 mm
Mounting: the nameplate is glued on

By default such a nameplate was fitted to most Carl Zeiss Jena microscopes from the Mikroval series onwards. There is also a smaller nameplate - with the manufacturer logo only (without the "Q1 Made in DDR" text). You can see it here: https://www.microscopeparts.eu/part/00604.

Because the adhesive used to attach these plates to the microscope body loses its properties over the years, these plates very often fall off. A nameplate like this makes it possible to restore the factory appearance of a microscope using original parts.