Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena NU-2

There are several models of mechanical microscope stages from Carl Zeiss Jena designed for microscopes of the Mikroval series. They differ mainly in the placement of the control knobs used for movement in both axes, for example:
- the Ergaval model has a short handle with control knobs
- the Amplival model has a long handle
- some variants of the Laboval model had a stage without a handle with control knobs, where the knobs were arranged horizontally on both sides of the stage.

However, many of the individual components used in these stages are identical.

Many of these stages can also be used interchangeably with other microscopes of the Mikroval series, which means that many microscopes today no longer have their original stages. For this reason it is best to examine the photos carefully to make sure that the element shown and offered here will fit.

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

Note that there are two such guides in the stage. They are made of a soft, thin piece of brass sheet and are often damaged; the bearing rollers also frequently fall out of them.

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

cover.

This microscope part was removed from a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

operation of 1 objective at a time - this is not a objective turret (revolver)
- the adapter allows work in brightfield mode
- the adapter does not support objectives with RMS thread (approx. 20 mm)

Description of this part for the microscope.

The Carl Zeiss Jena Amplival microscope has a modular design and by replacing individual elements it can be converted into other versions based on this platform, e.g. Amplival-Pol, Epival or Vertival.
After replacing the arm from a transmitted light version to one designed for reflected light, it is also necessary to supply light into the arm. This adapter is used for that purpose.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

microscope stage. Both are the same, and there's no difference between right and left. This knob moves the worm shaft (link: https://www.microscopeparts.eu/part/99272). The specimen holder carrier (link: https://www.microscopeparts.eu/part/99273) is mounted on this shaft and moves the specimen holder sideways (lateral movement).

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

main plate (forward-backward, i.e. longitudinal movement). There are two such knobs in the microscope stage, and the right and left are different. This is the left knob.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

main plate (forward-backward, i.e. longitudinal movement). There are two such knobs in the microscope stage, and the right and left are different. This is the right knob.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

160 mm
Focal Length: 45 mm
Cover Glass: no
Immersion: no
Thread: RMS
Info: Phv = phase contrast variable

It can be used with any microscope from any manufacturer, along with a compatible Phv phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

numbers. This microscope element bears the number 2480 (full designation: Si10 2480).

Inside there is a classic mirror reflecting light and a matte mirror diffusing light. Both are in very good condition.

Note - this base does not fit the first models of Carl Zeiss Jena Technival and Citoval stereomicroscopes, as they have a smaller stand foot.

The complete factory set consists of:
- transmitted light base
- wrist supports
- light source
Here I present and offer only the base - without wrist supports and without the light source.

Description of this part for the microscope.

transmitted light is inserted. Inside there is a lens that collimates the light beam. In the lower part of this element there are three filter holders and a shutter that allows complete cutoff of this light source.

The illumination block in the Carl Zeiss Jena Fluoval-2 fluorescence microscope is modular, and each of its elements can be easily detached and attached. This microscope element is mounted to the whole module using screws and the key https://www.microscopeparts.eu/part/00588.

Description of this part for the microscope.

micrometer scale: no
- dedicated for polarization: no
- material: brass
- mounting diameter: 71 mm

This stage fits the following microscopes:
- Carl Zeiss Jena L-Stativ
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lr
- Carl Zeiss Jena Lumipan

This Carl Zeiss Jena stage also fits microscopes:
- Lomo MBI-1
- Lomo MBR-3
- Lomo Biolam
- Lomo sold under the names Bresser and Zenith

If any of the above microscopes currently has a fixed stage (screwed), it is possible to retrofit a holder for interchangeable stages ( like this: https://www.microscopeparts.eu/part/99175) - this applies to both Carl Zeiss Jena and Lomo microscopes.

From the 1930s to approximately the mid-1960s many German manufacturers produced microscopes with the same stage mounting standard, so this stage will also fit them.

How does compatibility of stages between Carl Zeiss Jena and Lomo microscopes work?
- Carl Zeiss Jena stages for L-Stativ microscopes have a mounting diameter of 71 mm
- Lomo stages for MBR-3 / MBI-1 microscopes have a mounting diameter of 73 mm
- The spring-loaded front screw and long side centering screws in the mounting holder compensate for these differences
- Carl Zeiss Jena stages are more solid, heavier, made of brass
- Lomo stages are lighter, made of aluminium with plastic elements

Note that although this is a round and rotating stage, it is not a polarizing stage. It does not have a micrometer scale to read how many degrees (0-360) the rotation has occurred. Without this scale it can of course be used for amateur observations in polarized light, however for professional applications this is disqualifying.

Description of this part for the microscope.

micrometer scale: no
- dedicated for polarization: no
- material: aluminium with plastic elements
- mounting diameter: 73 mm

This stage fits the following microscopes:
- Lomo MBI-1
- Lomo MBR-3
- Lomo Biolam
- Lomo sold under the names Bresser and Zenith

This Lomo stage also fits microscopes:
- Carl Zeiss Jena L-Stativ
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lr
- Carl Zeiss Jena Lumipan

If any of the above microscopes currently has a fixed stage (screwed), it is possible to retrofit a holder for interchangeable stages (like this: https://www.microscopeparts.eu/part/99175) - this applies to both Lomo and Carl Zeiss Jena microscopes.

How does compatibility of stages between Carl Zeiss Jena and Lomo microscopes work?
- Carl Zeiss Jena stages for L-Stativ microscopes have a mounting diameter of 71 mm
- Lomo stages for MBR-3 / MBI-1 microscopes have a mounting diameter of 73 mm
- The spring-loaded front screw and long side centering screws in the mounting holder compensate for these differences
- Carl Zeiss Jena stages are more solid, heavier, made of brass
- Lomo stages are lighter, made of aluminium with plastic elements

From the 1930s to approximately the mid-1960s many German manufacturers produced microscopes with the same stage mounting standard, so this stage will also fit them.

Note that although this is a round and rotating stage, it is not a polarizing stage. It does not have a micrometer scale to read how many degrees (0-360) the rotation has occurred. Without this scale it can of course be used for amateur observations in polarized light, however for professional applications this is disqualifying.

Description of this part for the microscope.

mm
Focal Length: 33 mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

Description of this part for the microscope.

Carl Zeiss Jena Nf
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena NU / NU2

This lens DOES NOT FIT grey pancratic condensers from the following microscopes:
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Docuval

IOR Bucuresti and Lomo produced their own versions of pancratic condensers - I do not know whether this lens is compatible with them.

Description of this part for the microscope.

illumination.

The set consists of the following elements:
- potentiometer
- bulb holder / lamp socket
- halogen bulb 6V 30W
- transformer on the electronic board

Markings found on the electronic board:
- 0630
- 505
- 73
- 0630 505-73
- K&B 25/99
- E41625 FR4

This repair element may solve the following issues:
- power supply in Zeiss Axiolab microscope is burned out
- illumination in Zeiss Axiolab microscope does not work
- halogen bulb holder in Zeiss Axiolab is broken
- how to repair power supply in Zeiss Axiolab?
- electronics repair in Zeiss Axiolab microscope

Various names are commonly used for this microscope service element:
- power supply
- transformer unit
- lamp
- bulb holder
- lamp socket
- lamp housing
- halogen bulb
- illumination
- illuminator
- electrical system
- electronics
- electronic board
- potentiometer
- brightness control
- dimmer

Description of this part for the microscope.

The set includes a cable Zeiss P/N 452112-9081/X2.

This service part for repair of Zeiss Axiovert 100M microscope may solve the following issues:
- coarse movement does not work in Zeiss Axiovert 100M microscope
- fine movement does not work in Zeiss Axiovert 100M microscope
- where to find original spare parts for Zeiss Axiovert 100

The Zeiss Axiovert 100M microscope shares many components with the non-motorized version (Axiovert 100), so it is possible that this element can also be installed in the non-motorized version, i.e. Axiovert 100.

The photos show dimensions and exact appearance of this element from multiple views. Additionally, the video shows how the mechanism works.

Description of this part for the microscope.

electrical contacts

This service part for repair of Zeiss Axiovert 100M microscope may solve the following issues:
- no image on photo output in Zeiss Axiovert 100 microscope
- damaged image reflecting mirror in Zeiss Axiovert 100
- where to find original spare parts for Zeiss Axiovert 100

The Zeiss Axiovert 100M microscope shares many components with the non-motorized version (Axiovert 100), so it is possible that this element can also be installed in the non-motorized version, i.e. Axiovert 100.

The photos show dimensions and exact appearance of this element from multiple views. Additionally, the video shows how the mechanism works.

Description of this part for the microscope.

the image to the photo output. It also has two electrical contacts.

This service part for repair of Zeiss Axiovert 100M microscope may solve the following issues:
- no image on photo output in Zeiss Axiovert 100 microscope
- damaged image reflecting mirror in Zeiss Axiovert 100
- where to find original spare parts for Zeiss Axiovert 100

The Zeiss Axiovert 100M microscope shares many components with the non-motorized version (Axiovert 100), so it is possible that this element can also be installed in the non-motorized version, i.e. Axiovert 100.

The photos show dimensions and exact appearance of this element from multiple views. Additionally, the video shows how the mechanism works.

Description of this part for the microscope.

black Carl Zeiss Jena microscopes
- Nf
- Ng
- Lg
- Lr
- Lu
- Lumipan

as well as newer, gray Carl Zeiss Jena
- Ergaval
- Amplival
- Fluoval
- Epival
- Interphako
- Vertival
- and other variants

and
- Lomo Biolam
- Bresser Biolam
- Lomo MBB-1A
- Lomo MBI-1
- Lomo MBR-3
- and some IOR Bucuresti

have an interchangeable objective turret.

This is an excellent solution for owning, using, and quickly replacing entire sets of objectives.

For example, you can have separate turrets already equipped with a complete set of objectives:
- low magnification for observing macro objects with side illumination, without a cover glass (e.g., 2.5x / 3.2x / 5x / 8x / 10x)
- for phase contrast
- for various phase contrasts (positive, anoptral, amplitude, Zernike)
- for DIC
- for water immersion (e.g., Lomo)
- all for oil immersion (e.g., Leitz 10x Oil / 25x Oil / 40x Oil / 100x Oil)
- apochromatic for better color
- for polarization
- only high magnifications, e.g., for analyzing cell wall ornamentation (50x / 63x / 80x / 100x)
- for darkfield work (objectives with an iris diaphragm in the center)

Therefore, having only one microscope we can use it for different purposes and not screw in and unscrew all the lenses manually each time.

This is the newest, matte version of the objective revolver. If you're looking for the glossy version, see here: https://www.microscopeparts.eu/00736.

Description of this part for the microscope.

dimensions and exact appearance of this component from various angles. The first photo also shows the lens's precise position within the microscope.

The Opton ICM 405 (ICM-405, ICM405) is equivalent to the Zeiss IM 35 (IM-35, IM35) microscope.

Description of this part for the microscope.

They also act as vibration absorbers.

These rubber feet will likely fit other Zeiss inverted microscopes, such as the Axiovert 100 or Axiovert 200.

The photos show the dimensions and exact appearance of this part from multiple angles.

The equivalent of the Zeiss IM 35 (IM-35, IM35) is the Opton ICM 405 (ICM-405, ICM405).

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: micrometer
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: none
Mounting diameter: 23.2 mm

There is no measuring scale glass inside the eyepiece. Any 19mm diameter glass can be inserted inside, for example, with a crosshair, micrometer, or reticle.

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

08 160/-
Color correction: Planachromat
Numerical aperture: 0.08
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

filter holder of Carl Zeiss Jena Vertival microscopes.

Description of this part for the microscope.

160 mm
Focal Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: no
Thread: RMS
Info: Phv = phase contrast variable

It can be used with any microscope from any manufacturer, along with a compatible Phv phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

Length: 33 mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

Description of this part for the microscope.

Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: no
Thread: RMS
Info: Ph = phase contrast

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

mm
Focal Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: Ph3 = phase contrast

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

microscope from any manufacturer that allows the use of eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

yes

This condenser fits microscopes from many manufacturers (e.g. Steindorff Berlin, Zeiss, Carl Zeiss Jena, Leitz, Kremp Wetzlar, Will Wetzlar and many others) with a condenser holder diameter of 39.5 mm.

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

03
Magnification: 32x
Correction: achromat
Numerical aperture: 0.4
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 1 mm (!)
Immersion: no
Thread: RMS
Ph1: phase contrast
LD: "long distance" meaning long working distance

Note: this is an objective for an inverted microscope, therefore it is corrected for observation through a 1.0 mm cover glass

It can be used with any inverted microscope from any manufacturer together with a compatible phase contrast condenser (or slider with phase rings). Of course the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

It can very likely also be used with other inverted Zeiss microscopes (e.g. Axiovert 25).

Description of this part for the microscope.

06
Magnification: 20x
Correction: achromat
Numerical aperture: 0.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 2 mm (!)
Immersion: no
Thread: RMS
Ph1: phase contrast
LD: "long distance" meaning long working distance

Note: this is an objective for an inverted microscope, therefore it is corrected for observation through a 2.0 mm cover glass

It can be used with any inverted microscope from any manufacturer together with a compatible phase contrast condenser (or slider with phase rings). Of course the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

It can very likely also be used with other inverted Zeiss microscopes (e.g. Axiovert 25).

Description of this part for the microscope.

9904
Magnification: 10x
Correction: achromat
Numerical aperture: 0.22
Tube length: 160 mm
Focal length: 45 mm
Cover glass: indifferent
Immersion: no
Thread: RMS
Ph1: phase contrast

This specific unit was used in an inverted Zeiss ID 02 microscope, but I have also seen this objective model in Zeiss KF-2 ICS and Zeiss Axiostar microscopes.

Objectives with such low magnification (here 10x) can be used without a cover glass, with a cover glass, or for observation through thicker glass (e.g. through a Petri dish), therefore they can be used both in upright and inverted microscopes.

It can be used with any microscope from any manufacturer together with a compatible phase contrast condenser (or slider with phase rings). Of course the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

10x
Correction: Achromat
Numerical aperture: 0.24
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS
Info: PI = polarization-interference objective (red ring).

Compatible with the following PZO condensers:
- PZO KPI 2
- slit condenser
PI objectives are among the components of the PZO UPI set (i.e. the so-called DIC).

VERY IMPORTANT: the marking on the objective is "PI" (in lowercase: "pi"), meaning [P]-polarization [I]-interference.
In many descriptions available on the Internet, you can find information that this is a PLAN objective. This is an ERROR caused by misinterpreting the marking as PL.

Note: another INCORRECT piece of information often found online is that these are DIC objectives. This is not true.
DIC according to Pluta (niem: DIC nach Pluta), sold by PZO, achieves the DIC effect (i.e. a 3D relief image) using standard achromatic PZO objectives (and not only those). Objectives marked PI with a red ring are not required for this.

It can be used with any microscope from any manufacturer that supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

40
Mounting diameter: 39.5 mm
Iris diaphragm: yes
Filter holder: yes, for round filters with 32 mm diameter
Removable top lens: yes

This is a very rarely encountered condenser designed for use with high numerical aperture objectives (e.g. Nikon Plan Apo or Leitz PL-Fluotar Oel Fluoreszenz).

This condenser fits microscopes from many manufacturers (e.g. PZO, Zeiss, Carl Zeiss Jena, Leitz, Kremp Wetzlar, Will Wetzlar and many others) with a condenser holder diameter of 39.5 mm.

Description of this part for the microscope.

Zeiss DRC
- Zeiss DV-4

This microscope part may solve the following problems occurring in a Zeiss Stemi D, DR, DRC or DV 4 microscope:
- focusing does not work
- raising the microscope on the stand does not work
- lowering the microscope using the knobs does not work
- focusing rack has worn teeth

Description of this part for the microscope.

models:
- Zeiss D
- Zeiss DR
- Zeiss DRC
- Zeiss DV-4

This microscope part may solve the following problems occurring in a Zeiss Stemi D, DR, DRC or DV 4 microscope:
- missing eyepiece tube in the microscope
- eyepiece cannot be inserted into the tube
- eyepiece tube in the microscope is deformed

In the last photos, an arrow shows where this element is located inside the microscope head, allowing precise identification.

Description of this part for the microscope.

it is the left metal holder for the eyepiece prism
- at the same time it is the mounting thread into which the eyepiece tube is screwed

Important: this is the LEFT prism holder. In the head of the Zeiss DRC microscope (and other Stemi D series models) there are two such holders - left and right - and they are not identical.

This element is made of an alloy that very often breaks (this can be seen in one of the last photos in the gallery).

Fits the following models:
- Zeiss D
- Zeiss DR
- Zeiss DRC
- Zeiss DV-4

This microscope part may solve the following problems occurring in a Zeiss Stemi D, DR, DRC or DV 4 microscope:
- eyepiece tube cannot be screwed in
- thread inside the head is broken
- damaged microscope head

In the last photos, an arrow shows where this element is located in the head to allow correct identification.

Description of this part for the microscope.

it is the right metal holder for the eyepiece prism
- at the same time it is the mounting thread into which the eyepiece tube is screwed

Important: this is the RIGHT prism holder. In the head of the Zeiss DRC microscope (and other Stemi D series models) there are two such holders - left and right - and they are not identical.

This element is made of an alloy that very often breaks (this can be seen in one of the last photos in the gallery).

Fits the following models:
- Zeiss D
- Zeiss DR
- Zeiss DRC
- Zeiss DV-4

This microscope part may solve the following problems occurring in a Zeiss Stemi D, DR, DRC or DV 4 microscope:
- eyepiece tube cannot be screwed in
- thread inside the head is broken
- damaged microscope head

In the last photos, an arrow shows where this element is located in the head to allow correct identification.

Description of this part for the microscope.

interpupillary distance adjustment in Zeiss Stemi D series stereo microscopes (i.e. models D, DR, DRC and DV 4) is controlled by two plastic elements:
- right, female element with an opening
- left, male element with a protrusion fitting into the opening in the right element

The one shown here is the RIGHT (female) element.

This element is made of plastic and often breaks when the user tries to spread the eyepiece tubes too forcefully.

Compatible with the following models:
- Zeiss D
- Zeiss DR
- Zeiss DRC
- Zeiss DV-4

In the last images, an arrow indicates where this element is located in the microscope head to allow correct identification.

Description of this part for the microscope.

interpupillary distance adjustment in Zeiss Stemi D series stereo microscopes (i.e. models D, DR, DRC and DV 4) is controlled by two plastic elements:
- right, female element with an opening
- left, male element with a protrusion fitting into the opening in the right element

The one shown here is the LEFT (male) element.

This element is made of plastic and often breaks when the user tries to spread the eyepiece tubes too forcefully.

Compatible with the following models:
- Zeiss D
- Zeiss DR
- Zeiss DRC
- Zeiss DV-4

In the last images, an arrow indicates where this element is located in the microscope head to allow correct identification.

Description of this part for the microscope.

used, for example, in microscopes from Carl Zeiss Jena of the Mikroval series:
- Eduval
- Laboval
- Ergaval
- Amplival (entire series including Epival, Vertival, Amplival-Pol)
- Fluoval
- Metaval
- Telaval
- even Epignost

In microscope models with fluorescence illumination (e.g. Laboval Fluoreszenz or Fluoval), a filter wheel is installed in this head. When the manufacturer installed this head in other microscope models - a blanking plug was placed instead of the filter wheel - and this is exactly the element shown here.

Over the years, this element is very often lost and on the secondary market there are many such photo trino adapters without the blanking plug. The lack of this blanking plug can cause even large contaminants to enter the optics.

Description of this part for the microscope.

Description of this part for the microscope.

(changing) the objective, a "click" can be heard and felt, and the objective stops in the correct position. This part is a spring tab that falls into a corresponding recess (latch).

Detailed photos of this element along with dimensions are available in the image gallery. Additionally, in the last image an arrow indicates which element it is and where it is located, allowing clear identification of this part.

Description of this part for the microscope.

10 160/-
Color correction: Planachromat
Numerical aperture: 0.10
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Color correction: Planachromat
Numerical aperture: 0.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.32
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.