Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

20x / 0.45 oo/0.17-A
Color correction: Achromat
Numerical aperture: 0.45
Tube length: infinity
Focal length: not sure
Cover glass: 0.17 mm
Immersion: no
Thread: M25

This lens is often used with Leica microscopes (e.g., the DMLB, DMLS, or DM1000 models). It is often shorter than Leica objectives, but an extension adapter is used in these cases.

Description of this part for the microscope.

Achromat HI 100x / 1,25 oo/0.17-A
Color correction: Achromat
Numerical aperture: 1,25
Tube length: infinity
Focal length: not sure
Cover glass: 0.17 mm
Immersion: yes, oil
Thread: M25

This lens is often used with Leica microscopes (e.g., the DMLB, DMLS, or DM1000 models). It is often shorter than Leica objectives, but an extension adapter is used in these cases.

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

filter is exceptionally rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

installed. It enables ergonomic work with the microscope by tilting the observation head at an angle.

Note - this is not a tube with a photo port (that is, it is not a so-called "trino"). It is a tube intended for mounting a binocular head and it does not have a third optical light path.

Other names used for this microscope part:
- Angle tube
- Angular tube
- Inclined tube
- Intermediate tube
- Angle intermediate tube
- Inclined intermediate tube

Description of this part for the microscope.

This mounting screw fits most Carl Zeiss Jena microscopes of the CF250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenapol
- Jenatech
- Jenavert

Carl Zeiss Jena developed a complete modular microscope system based on connections using this type of screw. Therefore, this screw as a service part is also compatible with most accessories, modules and microscope elements that can be mounted to the microscope, including:
- magnification changers
- VIS analyzers
- trinocular heads
- Interphako heads

Important - carefully check the shape and dimensions of the screw to make sure it is the size you need. For example, the modular design of the Carl Zeiss Jena Amplival microscope is based on mounting screws of a different shape and size (search for it in this database to have a comparison).

Description of this part for the microscope.

into the slot located above the objective turret and below the microscope head.

Note - Carl Zeiss Jena produced several types of sliders with different dimensions and shapes. For Jenamed series microscopes there are at least six versions. Always carefully check the slider dimensions to make sure this is exactly the type you need. A millimeter scale is shown in each photo.

Description of this part for the microscope.

CZ

This is a slider inserted into the slot located above the objective turret and below the microscope head.

Note - Carl Zeiss Jena produced several types of sliders with different dimensions and shapes. For Jenamed series microscopes there are at least six versions. Always carefully check the slider dimensions to make sure this is exactly the type you need. A millimeter scale is shown in each photo.

Description of this part for the microscope.

stage and under the condenser, e.g. for discs used for phase contrast or darkfield
- three smaller sliders fit into three additional slots between the objective turret and the head (e.g. Pol analyzer, quartz ROT I and quarter-wave plate)

Note - Carl Zeiss Jena produced several types of sliders with different dimensions and shapes. There are at least six variants for microscopes of the Jenamed series. Always carefully check the slider dimensions to make sure this is the exact type you need. A millimeter scale is shown in each photo.

Description of this part for the microscope.

Jenalumar 50

Please note the following:
- both microscopes listed here use this illuminator for EPI fluorescence, i.e. reflected light. This is not transmitted-light fluorescence.
- this illuminator requires a Carl Zeiss Jena SH 50 power supply for operation
- the Carl Zeiss Jena Jenalumar microscope was produced in two variants - this illuminator fits the Jenalumar version with two small, separate illumination modules
- information can be found on the Internet claiming that this illuminator is suitable for Carl Zeiss Jena Jenavert microscopes. This is NOT correct.
- an HBO lamp is not the same as an XBO lamp.
- Jenamed microscopes other than the "Fluorescence" version have a differently mounted head and this illuminator CANNOT be installed on them.

Important - operating used, overheated HBO lamps, lamps with unknown operating time or from an uncertain source may result in explosion, damage to the illuminator, contamination of the room and a risk to the user's life and health. For this reason, this illuminator DOES NOT INCLUDE a light source (i.e. it does not include the HBO mercury burner).

Description of this part for the microscope.

molded parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the number 2580 (full designation: Si10 CZ 2580).

This is a service element (replacement part) for the trino head (head with photo output), suitable for Carl Zeiss Jena CF-250 microscopes. Please note that this is a microscope element for a microscope part (the trinocular head) and not a part for a specific microscope model.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the upper main part of the housing is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this housing DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the head, in order to clearly identify this part.

Many different names are commonly used for the trino head. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trino head
- trinocular head
- trinocular head unit
- photo dome
- photo tube
- inclined tube with photo output

Description of this part for the microscope.

assembly of two lenses
- knob for moving and shifting the lenses
- mechanism for moving and shifting the lenses

Metal, cast or injection-molded parts manufactured by Carl Zeiss Jena have their own identification numbers. In this mechanism the lens is mounted on a cast part marked with number 2582 (full marking: Si10 CZ 2582).

This is a service element (repair part) of the trinocular head (photo tube), suitable for Carl Zeiss Jena microscopes of the CF-250 series. Please note that this is an element (component) of a microscope part (German: "Fototubus") and not a part dedicated to a specific microscope model.

Carl Zeiss Jena microscopes of the CF-250 series have a modular design and the microscope part to which the eyepieces are mounted (commonly referred to as "head", "binocular" or "twin tube") is a separate element from the angle tube (sometimes the German term "Winkeltubus" is used). If the angle tube has a photographic output, it is referred to as a "photo tube". The Bertrand lens offered and described here is intended specifically for this microscope part.

Hinweis - Carl Zeiss Jena microscopes Jenapol and Jenatech, although they also belong to the CF-250 series, have a differently designed photographic output and this mechanism DOES NOT FIT these models.

Hinweis - Carl Zeiss Jena also produced a simplified version of the photo tube which does not contain a Bertrand lens inside. In the image gallery there is also a page from the manufacturer's catalog so that it is visible whether these versions differ externally in appearance. This Bertrand lens shown and offered here CANNOT be installed in such a simplified version of the photo tube.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is concerned and where it is located in the head, in order to clearly identify this part.

In common usage many names are used for the photo tube. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trinocular head
- trinocular microscope head
- trinocular head assembly
- photo dome
- inclined tube with photo output

Description of this part for the microscope.

allows correction of vision in one eye and proper adjustment of image focus.

Basic parameters:
- Type: tube with diopter correction ring
- Diameter of supported eyepieces: 30 mm
- Color: white

Fits 30 mm heads used, among others, in the following Carl Zeiss Jena microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

Description of this part for the microscope.

250 series microscopes.
Note that this element is a component of a microscope element (the angled tube) and not a part dedicated to a specific microscope model.

This element fits, among others, the following Carl Zeiss Jena microscopes from the CF-250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenavert
- Jenatech
- Jenapol

Important: the element DOES NOT INCLUDE the screw used to secure the microscope head.

Inside this element there is a protective glass (without its own magnification, so called "zero lens") with a violet anti-reflection coating.
Although this holder for the binocular microscope head and the holder located at the photographic port look the same, have the same dimensions and are mechanically compatible - they are NOT (!) identical.
- the binocular microscope head mount contains a protective glass with a violet anti-reflection coating
- the mount located at the photographic port contains a protective glass with a green anti-reflection coating.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

250 series microscopes.
Note that this element is a component of a microscope element (the angled tube with photo port) and not a part dedicated to a specific microscope model.

This element fits, among others, the following Carl Zeiss Jena microscopes from the CF-250 series:
- Jenamed
- Jenaval
- Jenalumar
- Jenavert
- Jenatech
- Jenapol

Important: the element DOES NOT INCLUDE the screw used to secure the microscope head.

Inside this element there is a protective glass (without its own magnification, so called "zero lens") with a green anti-reflection coating.
Although this holder at the photographic port and the holder for the binocular microscope head look the same, have the same dimensions and are mechanically compatible - they are NOT (!) identical.
- the binocular microscope head mount contains a protective glass with a violet anti-reflection coating
- the mount located at the photographic port contains a protective glass with a green anti-reflection coating.

The photos visible in the gallery show the exact dimensions of the element described and offered here. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the microscope head, in order to clearly identify this part.

Description of this part for the microscope.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the element is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this part DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos.

Description of this part for the microscope.

suitable for Carl Zeiss Jena CF-250 microscopes. Please note that this is a microscope element for a microscope part (the trinocular head) and not a part for a specific microscope model.

Carl Zeiss Jena CF-250 microscopes have a modular design, and the microscope part to which the eyepieces are mounted (commonly referred to as the "head", "binocular" or "binocular tube") is a separate element from the angled tube (sometimes the German term "Winkeltubus" is used). If the angled tube has a photographic output, it is referred to as a "Fototubus". It is precisely for this microscope part that the prism carrier is offered and described here.

Note - although the Carl Zeiss Jena Jenapol and Jenatech microscopes also belong to the CF-250 series, they have a differently constructed photographic output and this part DOES NOT FIT them.

The exact dimensions of the described and offered microscope element can be seen in the gallery photos. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located in the head, in order to clearly identify this part.

Many different names are commonly used for the trino head. It is worth listing them here - each of them refers to the same microscope part.
- photo head
- trino head
- trinocular head
- trinocular head unit
- photo dome
- photo tube
- inclined tube with photo output

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

06 oo/-A
Magnification: 3.2x
Numerical aperture N.A.: 0.006
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: not required, may be present or not
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

25 oo/-A
Magnification: 12,5x
Numerical aperture N.A.: 0.25
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: not required, may be present or not
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

17-A
Magnification: 25x
Numerical aperture N.A.: 0.50
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: yes, 0,17 mm
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

17-A
Magnification: 40x
Numerical aperture N.A.: 0.65
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: yes, 0,17 mm
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

commonly used in microscopes with a 30 mm eyepiece mounting diameter:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older microscopes of the Mikroval series (e.g. Ergaval and Amplival) - in such cases this eyepiece will also fit them, because - in general - eyepieces fit the head mounted on the microscope, not the microscope itself.

A single Carl Zeiss Jena PW 6.3x (25) eyepiece can solve the following problems:
- a second 6.3x eyepiece is missing to complete a pair
- a low magnification eyepiece is needed for use in a trinocular photo tube

Description of this part for the microscope.

Jena
Name: Grossfeld Binocular
Eyepiece mounting diameter: 30 mm
Microscope mount: 41 mm dovetail mount
Diopter adjustment: yes, for one eyepiece

The set also includes two eyepieces:
- Model: Carl Zeiss Jena GF-Pw 10x (25)
- Mounting diameter: 30 mm

This head is most commonly used in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, widefield binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older Mikroval series microscopes (for example Ergaval and Amplival). If the microscope is additionally equipped with GF-Planachromat series widefield objectives (or GF-Planapochromat objectives used in Docuval microscopes) - this creates the best possible combination for Carl Zeiss Jena microscopes with a 160 mm tube length.

This microscope head model is identical to the Baader Mark V binocular viewer used in astronomical telescopes and is often purchased by astronomy enthusiasts and adapted for telescope mounting.

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
Carl Zeiss Jena Jenamed 2 and Jenamed Histology microscopes already use different stages.

This particular example shown and offered here was removed from a Carl Zeiss Jena Jenamed Cytology microscope.

The stage in Carl Zeiss Jena Jenamed microscopes is a flat, smooth surface permanently attached with screws to the microscope body, onto which cross table mechanisms or specimen holders are mounted - various versions depending on individual needs.

Mechanically, this stage consists of two elements:
- a smooth upper steel surface attached to the cast form underneath
- the lower cast form (with manufacturer number), which is attached to the microscope body
Both parts have an opening for the microscope condenser. The condenser is mounted from the underside of the stage (condenser available separately).

Metal cast or injection-moulded microscope parts made by Carl Zeiss Jena have their own numbers. This part carries the number 2712 (full marking: Si10 CZ 2712).

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

microscope. It will most likely also fit other models from the Jenamed series (e.g. Jenamed Variant, Jenamed Fluorescence, Jenamed-2, Jenamed Hematology). Please note however that the Carl Zeiss Jena Jenamed Histology microscope is factory-equipped with a different type of condenser - the "flip-out" type.

To make sure whether this condenser will fit a specific Carl Zeiss Jena microscope from the Jenamed series, it is best to carefully check all dimensions based on the gallery photos or ask a question on a professional forum, e.g. https://www.mikroskopie-forum.de/

Mechanically, this condenser is mounted from the underside of the microscope stage - first it is screwed into the threaded opening in the stage and then secured with three screws. The upper lens can be unscrewed to obtain a condenser with a lower numerical aperture N.A. This condenser does not have an iris diaphragm installed because in Jenamed microscopes it is a separate element.

Replacing the condenser in a Carl Zeiss Jena Jenamed microscope may be necessary:
- when the upper lens becomes damaged, for example when it turns matte due to exposure to various chemical reagents
- when the upper lens becomes damaged due to rubbing. Surprisingly, this unusual type of damage is very common after several decades of microscope use.

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

was removed from a Carl Zeiss Jena Jenamed Cytology microscope. It will most likely also fit other models from the Jenamed series (e.g. Jenamed Variant, Jenamed Fluorescence, Jenamed-2, Jenamed Hematology).

It does not fit the Jenamed Histology model because the Carl Zeiss Jena Jenamed Histology microscope features a different type of condenser (a 'flip-out' type) by default. For this reason, the iris diaphragm is located slightly lower than in other models and is different.

To make sure whether this iris diaphragm will fit a specific Carl Zeiss Jena microscope from the Jenamed series, it is best to carefully check all dimensions based on the gallery photos or ask a question on a professional forum, e.g. https://www.mikroskopie-forum.de/

Mechanically, this diaphragm is mounted underneath the condenser. The entire diaphragm module is attached to the microscope body with four screws. It is not mechanically connected to the condenser - these are separate elements. The lever pin used to open / close the diaphragm protrudes through a special opening at the front of the microscope, making it possible to adjust the diaphragm opening. This opening is located in the cover of the filter wheel - here one can see further relationships between the individual elements of the light path.

Carl Zeiss Jena Jenamed microscopes do not have a field diaphragm.

Replacement of the aperture diaphragm module in a Carl Zeiss Jena Jenamed microscope may be necessary:
- when some of the iris diaphragm blades become damaged (bent or broken)
- when the lever used to open / close the diaphragm breaks off
- when the teeth of the gear wheel mounted in this module become damaged

Metal cast or injection-moulded microscope parts made by Carl Zeiss Jena have their own numbers. This part carries the number 2713 (full marking: Si10 CZ 2713).

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

Basic parameters:
- Number of objective positions: 5
- Thread: M25
- Mounting method: integrated with a larger block attached to the microscope body using screws

Yes - the "click-stop" detent mechanism (German: Blattfeder) is included, as it is frequently damaged in this model.

Metal cast or injection-moulded parts made by Carl Zeiss Jena have their own numbers. This part carries the number: 2708 (full marking: Si10 CZ 2708).

Please note - the small block with slots for microscope sliders, attached to this revolver and bearing the number Si10 CZ 2709/2, is available separately.

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

Variant, Cytology, Hematology, Histology, Jenamed-2, Fluorescence)
- Jenapol
- Jenavert
- Jenaval
- Jenatech
- Jenalumar

Please note - this is only the adjustment knob, that is the knob used by the microscope user to make the illumination brighter or dimmer. It is not a potentiometer and therefore not a part of the electrical circuit.

This knob features the characteristic white cap used on Carl Zeiss Jena microscopes, which is often lost during decades of microscope use.

Mechanically, this knob is attached to the potentiometer. The fixing screw is covered by a white metal cap.

In the last photo I indicate with an arrow exactly which element it is and where it is located in a Carl Zeiss Jena Jenamed microscope. In Jenaval and Jenalumar microscopes it is located on the microscope base.

Description of this part for the microscope.

Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

The function of this element is to reflect light coming from the microscope base vertically upwards so that, after passing through the microscope slide with the specimen and the objective, it reaches the eyepieces and ultimately the user's eyes.

Metal cast or injection-moulded parts made by Carl Zeiss Jena have their own numbers. This part carries the number: 2721 (full marking: Si10 CZ 2721).

Replacement of the angle mirror in Carl Zeiss Jena Jenamed microscopes may be necessary in the following cases, among others:
- if the mirror becomes significantly scratched as a result of improper cleaning (minor scratches are usually not visible during normal use)
- if the reflective silver coating of the installed mirror becomes oxidised
- if the mirror becomes damaged, chipped or cracked, for example after coming loose from its mount

Description of this part for the microscope.

attached to the microscope stand with screws. It serves as a mounting platform for mechanical stages, XY stage mechanisms, or specimen holders - various versions depending on the user's requirements.

Mechanically, this stage consists of two elements:
- a smooth upper steel plate attached to the cast component below
- a lower cast component (with the manufacturer's part number) attached to the microscope stand
Both parts have an opening for the microscope condenser. The condenser is mounted from below the stage (condenser available separately).

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This part is marked with number 2712 (full marking: Si10 CZ 2712).

This microscope stage DOES NOT FIT the following Carl Zeiss Jena microscopes:
- Jenamed 2
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Fluorescence

More precisely: the lower part (marked Si10 CZ 2712) is identical to the one used in other Jenamed microscope models (except Jenamed-2), whereas the smooth upper steel plate used in the Jenamed Histology differs from those used in other models by the size of the condenser cut-out (opening).

In the last photo, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

This diaphragm DOES NOT FIT the following Carl Zeiss Jena microscopes:
- Jenamed 2
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Fluorescence

Mechanically, this diaphragm is mounted below the condenser. The complete diaphragm module is attached to the microscope stand with two screws. It is not mechanically connected to the condenser - these are separate components. The lever (pin) used to open and close the diaphragm extends through a dedicated opening at the front of the microscope, allowing adjustment of the diaphragm opening. This opening is located in the cover of the filter wheel - illustrating further relationships between successive elements of the light path.

Carl Zeiss Jena Jenamed microscopes do not have a field diaphragm.

Replacement of the aperture diaphragm module in a Carl Zeiss Jena Jenamed Histology microscope may be necessary:
- when one or more iris diaphragm blades become damaged (bent or broken)
- when the lever used to open and close the diaphragm breaks off
- when the teeth of the gear wheel installed in this module become damaged

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This part bears number 2714 (full marking: Si10 CZ 2714). The iris diaphragm module used in the other Carl Zeiss Jena Jenamed microscope models bears part number Si10 CZ 2713.

Description of this part for the microscope.

therefore cannot be used in:
- Jenamed Cytology
- Jenamed Variant
- Jenamed Hematology
- Jenamed Fluorescence
- Jenamed-2

Mechanically, this condenser is a "flip-out" design and is mounted in a metal frame together with a lever used to rotate it in order to obtain one of two operating modes: low or high numerical aperture N.A. This lever extends outside the microscope housing so that the user can operate it.

The complete module is mounted underneath the microscope stage by attaching the entire condenser assembly from below with four screws. This condenser does not contain an iris diaphragm because, in Jenamed microscopes, it is a separate component mounted beneath the condenser.

In the Carl Zeiss Jena Jenamed Histology microscope, this condenser is not used together with the wide-field lens that is installed beneath the condenser in other Jenamed models (part Si10 CZ 2711-1). In the Jenamed Histology model, a polarizer is installed in this position instead.

Replacement of the condenser in a Carl Zeiss Jena Jenamed Histology microscope may be necessary:
- when the upper lens becomes damaged, for example by becoming cloudy due to exposure to various chemical reagents
- when the upper lens is damaged by friction. Surprisingly, this unusual type of damage is very common after several decades of microscope use
- when the mechanical lens switching mechanism ("flip-out") becomes damaged

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This condenser module bears number 2713 (full marking: Si10 CZ 2713).

In the last photograph, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

2 Fluorescence

It DOES NOT FIT Carl Zeiss Jena microscopes from the Jenamed series and therefore cannot be used in:
- Jenamed Cytology
- Jenamed Variant
- Jenamed Hematology
- Jenamed Histology

Mechanically, this condenser is mounted on the microscope stage support plate (stage support). The microscope stage is installed onto this support plate together with the condenser. The upper condenser lens can be unscrewed - after removing it, the condenser operates with a lower numerical aperture N.A.

This condenser does not contain an iris diaphragm because, in Jenamed microscopes, it is a separate component mounted beneath the condenser.

Replacement of the condenser in a Carl Zeiss Jena Jenamed-2 microscope may be necessary:
- when the upper lens becomes damaged, for example by becoming cloudy due to exposure to various chemical reagents (common in fluorescence applications)
- when the upper lens is damaged by friction. Surprisingly, this unusual type of damage is very common after several decades of microscope use

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. The microscope stage support plate on which the condenser is mounted bears number 3030 (full marking: Si10 CZ 3030).

In the last photograph, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

This is a microscope element placed in the microscope base. It transmits the light beam from the illuminator, unifies it (blurs the filament image using a diffuser), and then properly focuses it using a collimating lens. The light beam prepared in this way then hits an angular mirror (this is a separate element).

This microscope part is known on the secondary market among DIY enthusiasts creating their own optics projects and is frequently used by them.

Description of this part for the microscope.

Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed-2
- Jenamed Fluorescence

Important: this element is not used in the Jenamed Histology model. In this microscope version, a flip-out type condenser is used, and instead of the wide-field lens there is a polarizer. In other words - this element does not fit the Carl Zeiss Jena Jenamed Histology microscope.

This lens enables uniform illumination of the specimen when working with low magnification objectives. It is most commonly used with 3.2x and 5x objectives. It is an element installed in the microscope base and is part of the transmitted light illumination system.

Mechanically, this lens has a pin that extends outside the housing so that the user can insert or remove the lens from the optical path. It is mounted below the condenser aperture diaphragm. In Jenamed microscopes, the condenser, the aperture diaphragm, and this wide-field lens are all separate modules.

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This condenser module bears number 2711-1 (full marking: Si10 CZ 2711-1).

Description of this part for the microscope.

following Carl Zeiss Jena microscopes:
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology

This is a large module that is mechanically integrated, although it can be disassembled into smaller parts. However, if replacement becomes necessary, it is usually more convenient to replace the complete assembly. For this reason it is presented and offered here as a complete unit.

The assembly shown here includes:
- internal power supply electronics (potentiometer, transformer, etc.)
- fine focus mechanism (micro-adjustment)

If you need any individual component from this assembly, for example the transformer, a specific electronic board, only the brightness control potentiometer, or only the fine focus mechanism itself, please contact us by email.

Please note:
- the power supply is compatible with every Carl Zeiss Jena Jenamed microscope model, including Jenamed 2 and Jenamed Fluorescence
- however, the complete fine focus mechanism assembly does NOT fit Jenamed-2 and Jenamed Fluorescence, although some smaller components of the fine focus mechanism are identical across all Jenamed microscope models

This complete assembly may be required to solve, among others, the following problems in Carl Zeiss Jena Jenamed microscopes:
- when the microscope illumination does not work due to a defective power supply. This may be caused by mains voltage surges, ageing electronic components, or damage resulting from improper modifications (for example LED conversions)
- when the illumination works but brightness adjustment does not function because of a defective or worn potentiometer
- when the fine focus mechanism does not work properly, for example when the objective turret does not move upward or slowly drops by itself

It is very important to note that the internal power supply used in Carl Zeiss Jena Jenamed microscopes converts 220-240V mains voltage to 6V with a maximum power output of 25W. This power supply has the same specifications as those used in Carl Zeiss Jena Jenaval and Carl Zeiss Jena Jenalumar microscopes. If you own one of these microscopes with a defective power supply, any qualified electronics technician can transfer the electronics from a Jenamed microscope.

Description of this part for the microscope.

for microscope slides. It allows quick insertion and replacement of slides without the use of an XY mechanical stage.

Several different specimen holding systems are found in Carl Zeiss Jena microscopes. The slide cassette system is one of them and represents an alternative to traditional designs using a mechanical stage and slide-retaining clips.

Various names are commonly used for this specimen holder, including:
- slide cassette (German: Gleitkassette)
- specimen cassette (Ger.: Objektkassette)
- microscope specimen cassette
- specimen holder
- slide holder

This is not a complete stage-mounted system and therefore it is not a "slide cassette system". It is only the cassette itself (slide cassette), which is a replaceable wear item installed into the appropriate carrier assembly.

In the last gallery photograph, I indicate the exact component being offered with an arrow.

Description of this part for the microscope.

objective nosepiece. It consists of slots (empty openings) into which filter sliders are inserted. This is the component that the Microscopy-UK portal (https://www.microscopy-uk.org.uk/mag/imgmar09/JenamedFinal.pdf) referred to as "in-tube filter holders".

This filter holder is compatible with the following Carl Zeiss Jena microscopes:
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

Metal, cast, and injection-moulded parts manufactured by Carl Zeiss Jena have their own identification numbers. This part bears the number: 2709/2 (full designation: Si10 CZ 2709/2).

Mechanically, this "block with empty slots" is attached to the casting numbered Si10 CZ 2708, which is the objective nosepiece block.

In the last photo of the gallery, I use an arrow to show exactly which component is being described.

Description of this part for the microscope.

Carl Zeiss Jena microscope heads with a wide field of view (German: Grossfeld) have one eyepiece tube with diopter adjustment and a second one without it. Here I present the tube without diopter adjustment (straight eyepiece tube).

Basic parameters:
- Type: straight eyepiece tube
- Compatible eyepiece diameter: 30 mm
- Colour: white

Compatible with 30 mm microscope heads used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

Description of this part for the microscope.

hand when adjusting the interpupillary distance. It is a rounded metal cover that protects the eyepiece prism located underneath.

The last photo in the gallery shows a complete microscope head. An arrow indicates exactly which component is being described and where it is located inside the head, making it easy to identify.

Carl Zeiss Jena wide field microscope heads (those designed for 30 mm eyepieces) have two such components (two prism covers). They protect the prisms of the right and left eyepieces. Both covers are identical and interchangeable, so there is no constructional difference between the right-hand and left-hand cover.

This is a component for a microscope head, not for a specific microscope model.

This component fits microscope heads designed for 30 mm eyepieces used, among others, in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Metal cast or injection-moulded components manufactured by Carl Zeiss Jena have their own part numbers. This component is marked with the number 2630 (full designation: Si10 2630 / Si10 CZ 2630). In addition, the number "1" or "2" appears next to the part number to indicate whether it is the cover for the right-hand or left-hand prism. This is the only difference, because mechanically the right-hand and left-hand covers are identical.

Description of this part for the microscope.

the front, in the centre of the binocular head, between the two eyepiece tubes. It is a round cover plate (end cap) carrying a scale from 55 to 75 indicating the interpupillary distance (eyepiece tube spacing).

The last photograph in the gallery shows the complete binocular head. An arrow indicates the exact component being offered and its location within the head, allowing it to be identified unambiguously.

This is a component of the binocular head rather than a component dedicated to a particular microscope model.

This component fits 30 mm eyepiece binocular heads used, among others, on the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Some Carl Zeiss Jena Jenalab and Jenamed microscopes (for example the Jenamed Fluorescence) were factory-equipped with binocular heads accepting 23.2 mm eyepieces. In that case this end cap is **not** compatible with that binocular head. By "that" I specifically mean the binocular head, as this is a component of the head rather than of the microscope itself.

Interestingly, 30 mm wide-field binocular heads are also occasionally fitted to older microscopes from the Mikroval series (for example Ergaval and Amplival). When combined with GF-Planachromat or GF-Planapochromat objectives (the latter also used on the Docuval), this provides arguably the best optical combination available for Carl Zeiss Jena microscopes with a 160 mm tube length.

The Carl Zeiss Jena wide-field binocular head for 30 mm eyepieces is mechanically the same device as the Baader Mark V binocular viewer used with astronomical telescopes. They are based on the same binocular head; the Baader Mark V differs only in having a modified mounting interface, astronomical eyepiece adapters and, in some versions, different external markings. Consequently, the component offered here is also compatible with the Baader Mark V binocular viewer.

Description of this part for the microscope.

microscope head to the microscope.

Basic specifications:
Mount type: dovetail
Diameter: 41 mm, the Carl Zeiss Jena and Lomo standard
Internal thread: 34 mm

The last photograph in the gallery shows a complete binocular head. An arrow indicates exactly which component is being offered and where it is located on the head, making visual identification straightforward.

This is a component of the microscope head rather than of any specific microscope model.

This component fits 30 mm binocular heads used, among others, on the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

This 41 mm Carl Zeiss Jena dovetail mounting standard is commonly used:
- if you want to perform a DIY conversion and mount a microscope head from another manufacturer onto a Carl Zeiss Jena or Lomo microscope
- if you want to connect another dovetail-mounted accessory to a Carl Zeiss Jena or Lomo microscope, such as an Optovar magnification changer, a polarisation intermediate tube, a DIC head or an EPI reflected-light illuminator
- if you want to use the 34 mm internal thread to mount a photographic tube for a camera

Description of this part for the microscope.

17-A
Magnification: 50x
Numerical aperture N.A.: 0.95
Optical correction: Apochromat
Additionally: cover glass thickness correction collar, range 0.12 - 0.22 mm
Tube length: infinity
Thread: M25
Cover glass: yes, required
Immersion: no (so-called dry objective)

Commonly used, cheap cover glasses are 0.17 mm thick mostly on paper. Even the standard for class #1.5 allows a range of 0.16-0.19 mm, and cheap Chinese cover glasses in practice come in anywhere from approx. 0.13 to 0.25 mm, often not matching the thickness stated on the box. Only #1.5H (high precision) cover glasses have a guaranteed thickness of 0.170 mm with a tolerance of +/- 0.005 mm. With high-aperture dry objectives such as this Apochromat 50x/0.95, variation in cover glass thickness noticeably reduces image contrast and resolution (spherical aberration). The correction collar fitted to this objective lets you adjust the optics to the combined thickness of the cover glass and the mounting medium layer beneath it, within a range of 0.12 mm to 0.22 mm. This compensates for most of the variation encountered in practice.

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

As for the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

be attached to a trinocular head or directly to the microscope body, even when there is no trinocular head.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: grey
Tilt angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to the trinocular head or microscope body: ring with a dovetail
Dovetail diameter: 41 mm
Type of connection at the output: empty tube / barrel
Tube diameter at the output: 23.2 mm internal diameter
Length of the barrel / tube: 25 mm
Length adjustment: no - this is not a tube with adjustable height

Since the adapter has an empty barrel with an internal diameter of 23.2 mm on the output side, a projection eyepiece of that diameter can be placed in it, or a so-called "USB eyepiece", that is a digital microscope camera. Adapters between the 23.2 mm barrel and the M42 thread are also widely available, and from the M42 thread you can move on to any other mount: Nikon, Canon, Sony and others.

Such a tube can be mounted directly on the microscope body instead of the head. A dovetail seat with a diameter of 41.0 - 41.5 mm is found, among others, on the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH

It is also often used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can equally well be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol microscopes
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in the LOMO Polam microscopes
- some versions of the intermediate photo tubes for the Carl Zeiss Jena Mikroval series microscopes (others require a tube screwed onto a thread)

This is not a "tube for one specific microscope model". A trinocular head can be mounted not only on the microscope it was sold with - it is therefore correct to assume that this is a universal tube, with a 41 mm dovetail on one side and a 23.2 mm barrel on the other.

The "compatibility" section gives an example list of microscopes this tube fits, although it is not a complete list.

Description of this part for the microscope.

Zeiss Jena
Lettering: Jenamed hematology
Material: aluminium
Length: 65 mm
Width: 12 mm
Mounting: the plate is glued on

By default, such a plate was fitted to every Carl Zeiss Jena Jenamed microscope in the "hematology" version. Since the adhesive used to attach these plates to the microscope body loses its properties over the years, these plates very often fall off.

Such a plate lets you bring your microscope back to its factory appearance using original parts.

Description of this part for the microscope.

camera to a trinocular head or directly to the microscope stand, even when there is no trinocular head at all.

This is a black tube with an upper element (barrel) 55 mm long. Here (https://www.microscopeparts.eu/gallery/91057) you can see a functionally identical adapter, but grey and with an upper barrel only 25 mm long.

Black adapters of this kind come from the era of the Carl Zeiss Jena L stands (models Carl Zeiss Jena Lg, Lumipan, Ng, Nf or Nu). The grey ones are newer, from the era of the Mikroval series (models Carl Zeiss Jena Laboval, Eduval, Ergaval or Amplival and Docuval).

The mounting fit is of course identical, so both can be used interchangeably.

Basic technical parameters of this tube:
Manufacturer: Carl Zeiss Jena
Colour: black
Inclination angle: none, this is a straight tube
Internal optics: none - not even a deflecting prism
Mounting to a trinocular head or microscope stand: ring dovetail
Ring dovetail diameter: 41.5 mm
Type of connection at the output: empty barrel / tube
Tube diameter at the output: 23.2 mm inner diameter
Barrel / tube length: 55 mm
Tube length adjustment: no - this is not a height-adjustable tube

Because on the output side this adapter has an empty barrel with an inner diameter of 23.2 mm, you can place in it a projection eyepiece of that diameter or a so-called USB eyepiece, that is a digital microscope camera. In addition, adapters between the 23.2 mm barrel and the M42 thread are widely available, and from the M42 thread you can already move on to any other mount: Nikon, Canon, Sony and all the rest.

Such a tube can be mounted directly on the microscope stand, in place of the head. A seat for a ring dovetail of 41.0 - 41.5 mm diameter is found among others in the microscopes:
- Carl Zeiss Jena
- LOMO
- Meopta
- IOR
- Reichert Biopan
- Olympus CH
- Gamma

It is also used in microscopes with a slightly larger seat, among others Zeiss West Germany, Leitz Wetzlar, PZO, Will Wetzlar, Hund Wetzlar.

The adapter can likewise be fitted onto trinocular heads, as many of them have a seat prepared for it, among others:
- the output in the trinocular tubes of the microscopes Carl Zeiss Jena Jenamed, Jenaval, Jenalumar, Jenatech, Jenavert, Jenapol
- the LOMO TRN-1 heads (ЛОМО ТРН-1), found in LOMO Polam microscopes
- some versions of the black intermediate photo tubes for the microscopes Carl Zeiss Jena Lg / Lumipan / Nf and of the grey ones from the Mikroval series (others require a tube that screws in on a thread)

This is not a tube for one particular microscope model. A trinocular head can be mounted not only on the microscope it was sold with, so the correct assumption is that this is a universal tube with a ring dovetail of 41.5 mm diameter on one side and a barrel of 23.2 mm diameter on the other.

In the compatibility section you will find an example list of microscopes this tube fits, although that list is not complete.

Description of this part for the microscope.

Jena
Inscription: logo "Carl Zeiss Jena" and text "Q1 MADE IN DDR"
Material: aluminium
Length: 52 mm
Width: 14 mm
Mounting: the nameplate is glued on

By default such a nameplate was fitted to most Carl Zeiss Jena microscopes from the Mikroval series onwards. There is also a smaller nameplate - with the manufacturer logo only (without the "Q1 Made in DDR" text). You can see it here: https://www.microscopeparts.eu/part/00604.

Because the adhesive used to attach these plates to the microscope body loses its properties over the years, these plates very often fall off. A nameplate like this makes it possible to restore the factory appearance of a microscope using original parts.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP425
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - because this is an interference filter (it has a mirrored surface), the angle at which the filter sits relative to the incoming light matters and affects its parameters.

The coating on interference filters is sensitive not only to mechanical damage, for example scratches from improper storage or cleaning. Several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP490
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - this is an interference filter, which you can tell from the mirrored surface. For that reason the angle at which the filter sits relative to the incoming light matters and affects its parameters.

The coating on interference filters is sensitive to mechanical damage, for example scratches from improper storage or cleaning. Age is a separate matter - several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: KP560
Type: interference excitation filter for fluorescence
Diameter: 32 mm
Mirror coating: yes

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Note - the mirrored surface gives away that this is an interference filter. With filters of this kind the angle to the incoming light is not indifferent and affects their parameters.

The coating on interference filters is sensitive to mechanical damage, for example scratches from improper storage or cleaning. The second enemy is time - several decades of work right next to the HBO lamp can cloud it or make it delaminate, which shows as patches or rainbow islands that do not disappear when you rotate it. In that case the best solution is to replace the filter with one like the one I offer here.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B226g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The letter "g" at the end of the designation is short for the German gehärtet, meaning toughened - the manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red passed by that filter and to narrow the excitation band further.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B228g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The "g" at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red that filter passes and to narrow the excitation band further.

Description of this part for the microscope.

Carl Zeiss Jena
Model: B229g
Filter type: red-absorbing glass filter (the manufacturer calls it Rotsperrfilter)
Diameter: 32 mm
Colour: blue
Toughened version: yes

The "g" at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

In the excitation path this filter does not work on its own. It is added to the main filter to cut off the red that filter passes and to narrow the excitation band further.

Description of this part for the microscope.

filter:
Manufacturer: Carl Zeiss Jena
Model: U204g
Filter type: glass excitation filter for UV fluorescence (the manufacturer calls it Erregerfilter)
Glass type: UG 1
Diameter: 32 mm
Thickness: 2 mm
Colour: black-violet, passes very little visible light
Toughened version: yes

The g at the end of the designation stands for the German gehärtet, meaning toughened. The manufacturer gave it to filters meant to work right next to high-power lamps, especially HBO mercury burners, where ordinary glass does not withstand the high temperature. With a UV excitation filter this matters especially, because it sits at the hottest point of the whole path and absorbs most of the burner energy.

Filters 32 mm in diameter can be used in most microscopes from many manufacturers. In Carl Zeiss Jena microscopes they can be used, among others, in the following fluorescence microscopes:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval / Fluoval-2
- Carl Zeiss Jena Laboval Fluorescence

The manufacturer catalogue gives the following transmission values for this glass at 2 mm thickness:
- 0.015 at 302 nm
- 0.093 at 312 nm
- 0.435 at 334 nm
- 0.644 at 366 nm

Across the whole visible range, from 405 to 644 nm, transmission is zero. This means the filter works almost entirely on the 366 nm mercury line, exactly where the HBO burner is strongest in the ultraviolet.

One property of this glass is worth knowing: above 700 nm it starts to transmit again, and at 750 nm transmission reaches 0.210. This infrared leak is invisible to the eye, but it heats the specimen and spoils contrast in photographs.

In the excitation path U204 is also combined with a red-absorbing filter. The manufacturer documentation shows such a pair with the B226 filter, which cleans up the excitation band further.

The same UG 1 glass was supplied in two thicknesses, each with its own designation:
- The Carl Zeiss Jena U204 filter is UG 1 glass 2 mm thick
- The Carl Zeiss Jena U205 filter is UG 1 glass 4 mm thick

The thicker U205 cuts more sharply, but passes about a third less energy on the 366 nm line, so the image is noticeably darker.

A safety note: this filter passes ultraviolet, which is invisible and harmful to the eyes. When working with it, never look into the illumination path without a barrier filter in place.