Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

Dovetail/mounting connector for the microscope body
- Dovetail connector diameter: 43 mm
- Lower bottom lens

Here is the same part, but with screws.

Sorry, I don't know the part number. It's a binocular head mounted on Carl Zeiss Standard 14 and Standard 16 microscopes.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Gleitfett grades differ in their parameters.

Gleitfett I E10 and Gleitfett II E75 were supplied with the Carl Zeiss Jena micromanipulator.
The Gleitfett III E410 offered here was supplied with the Carl Zeiss Jena Neophot-21 microscope.

This MAY suggest (although I have no proof in the form of manufacturer documentation) that the lower numbers (I and II) and the lower values of the "E" parameter (E10 and E75) were intended for finer mechanisms - and may therefore have a lower viscosity, for example. The III E410 grease, with its high "E" value, was supplied with a heavy microscope built around massive mechanics - so it may well be thicker.

This grease can of course be used on microscopes from other manufacturers as well - a few are listed in the "compatibility" section, but that is by no means a complete list.

Description of this part for the microscope.

Zeiss IM 35 (IM-35, IM35) microscope is the Opton ICM 405 (ICM-405, ICM405).

Please note that exactly the same (!) illuminator is also used on the Zeiss Standard / Photomicroscope series microscopes. Please refer to the description of illuminator No. 99684 in this database. YES - these are exactly the same illuminators. However, that particular unit was removed from a Zeiss Photomicroscope II and therefore has its own separate description. You will also find additional photographs and an extended description there.

Description of this part for the microscope.

Standard 14 microscope

I apologize, but I don't know the P/N number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads - but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads - but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

P/N number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads?but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

Dovetail/mounting connector for the microscope body
- Dovetail connector diameter: 43 mm
- Lower bottom lens

Here is the same part, but without the screws.

Sorry, I don't know the part number. It's a binocular head mounted on Carl Zeiss Standard 14 and Standard 16 microscopes.

Description of this part for the microscope.

transmitted or reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Model: D42 15x
Magnification: 15x
Image: micrometer and X-crosshair
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Identical K15x eyepieces were also made by other manufacturers, such as Lomo and PZO.

Description of this part for the microscope.

removed from a Zeiss stage P/N 47 33 56 (473356-9901), however stages with other part numbers (e.g. Zeiss P/N 4693640) have an identical design, therefore it most likely fits many models of round Zeiss stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Universal
- Zeiss Photomicroscope (so-called Zeiss Phomi)
- Zeiss Ultraphot

In the photo gallery there are detailed images of this element together with dimensions. Additionally, in the last photo an arrow indicates which part is being referred to and where it is located in the stage, in order to clearly identify this component.

Description of this part for the microscope.

from a Zeiss stage P/N 47 33 56 (473356-9901), however stages with other part numbers (e.g. Zeiss P/N 4693640) have an identical design, therefore it most likely fits many models of round Zeiss stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Universal
- Zeiss Photomicroscope (so-called Zeiss Phomi)
- Zeiss Ultraphot

In the photo gallery there are detailed images of this element together with dimensions. Additionally, in the last photo an arrow indicates which part is being referred to and where it is located in the stage, in order to clearly identify this component.

Description of this part for the microscope.

was removed from a Zeiss stage P/N 47 33 56 (473356-9901), however stages with other part numbers (e.g. Zeiss P/N 4693640) have an identical design, therefore it most likely fits many models of round Zeiss stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Universal
- Zeiss Photomicroscope (so-called Zeiss Phomi)
- Zeiss Ultraphot

In the photo gallery there are detailed images of this element together with dimensions. Additionally, in the last photo an arrow indicates which part is being referred to and where it is located in the stage, in order to clearly identify this component.

Description of this part for the microscope.

stage P/N 47 33 56 (473356-9901), however stages with other part numbers (e.g. Zeiss P/N 4693640) have an identical design, therefore it most likely fits many models of round Zeiss stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Universal
- Zeiss Photomicroscope (so-called Zeiss Phomi)
- Zeiss Ultraphot

In the photo gallery there are detailed images of this element together with dimensions. Additionally, in the last photo an arrow indicates which part is being referred to and where it is located in the stage, in order to clearly identify this component.

Description of this part for the microscope.

removed from a Zeiss stage P/N 47 33 56 (473356-9901), however stages with other part numbers (e.g. Zeiss P/N 4693640) have an identical design, therefore it most likely fits many models of round Zeiss stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Universal
- Zeiss Photomicroscope (so-called Zeiss Phomi)
- Zeiss Ultraphot

In the photo gallery there are detailed images of this element together with dimensions. Additionally, in the last photo an arrow indicates which part is being referred to and where it is located in the stage, in order to clearly identify this component.

Description of this part for the microscope.

stage surface - in other words: end stop.

This part was removed from a Zeiss stage P/N 47 33 56 (473356-9901), however stages with other part numbers (e.g. Zeiss P/N 4693640) have an identical design, therefore it most likely fits many models of round Zeiss stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Universal
- Zeiss Photomicroscope (so-called Zeiss Phomi)
- Zeiss Ultraphot

In the photo gallery there are detailed images of this element together with dimensions. Additionally, in the last photo an arrow indicates which part is being referred to and where it is located in the stage, in order to clearly identify this component.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

Note that there are two such guides in the stage. They are made of a soft, thin piece of brass sheet and are often damaged; the bearing rollers also frequently fall out of them.

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

cover.

This microscope part was removed from a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

microscope stage. Both are the same, and there's no difference between right and left. This knob moves the worm shaft (link: https://www.microscopeparts.eu/part/99272). The specimen holder carrier (link: https://www.microscopeparts.eu/part/99273) is mounted on this shaft and moves the specimen holder sideways (lateral movement).

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

main plate (forward-backward, i.e. longitudinal movement). There are two such knobs in the microscope stage, and the right and left are different. This is the left knob.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

main plate (forward-backward, i.e. longitudinal movement). There are two such knobs in the microscope stage, and the right and left are different. This is the right knob.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: micrometer
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: none
Mounting diameter: 23.2 mm

There is no measuring scale glass inside the eyepiece. Any 19mm diameter glass can be inserted inside, for example, with a crosshair, micrometer, or reticle.

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

08 160/-
Color correction: Planachromat
Numerical aperture: 0.08
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

Description of this part for the microscope.

Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: no
Thread: RMS
Info: Ph = phase contrast

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

mm
Focal Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: Ph3 = phase contrast

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

9904
Magnification: 10x
Correction: achromat
Numerical aperture: 0.22
Tube length: 160 mm
Focal length: 45 mm
Cover glass: indifferent
Immersion: no
Thread: RMS
Ph1: phase contrast

This specific unit was used in an inverted Zeiss ID 02 microscope, but I have also seen this objective model in Zeiss KF-2 ICS and Zeiss Axiostar microscopes.

Objectives with such low magnification (here 10x) can be used without a cover glass, with a cover glass, or for observation through thicker glass (e.g. through a Petri dish), therefore they can be used both in upright and inverted microscopes.

It can be used with any microscope from any manufacturer together with a compatible phase contrast condenser (or slider with phase rings). Of course the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

10 160/-
Color correction: Planachromat
Numerical aperture: 0.10
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Color correction: Planachromat
Numerical aperture: 0.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.32
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 1,25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: HI = Homogene Immersion, also oil immersion

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

in microscopes:
- Zeiss Phomi (Zeiss Photomicroscope)
- Zeiss Ultraphot
- Zeiss Universal
and others, most often the Zeiss Standard series.

Description of this part for the microscope.

This particular screw was removed from a Zeiss Standard 14 microscope, but it will most likely fit most models of the Standard series, for example:
- Zeiss Standard GFL
- Zeiss Standard 16
- Zeiss Standard WL 89
- Zeiss Standard Universal
- Zeiss Standard Photomicroscope
- Zeiss Ultraphot

Note - over the years, Zeiss microscopes (or the same microscopes sold under the Zeiss-Winkel name or under the Opton brand), especially simpler models such as the Zeiss Standard Junior, used different types of head-retaining screws. These were not necessarily spring-loaded screws - in some cases ordinary threaded clamping screws were used instead.

Before deciding to replace the screw in a microscope, it is best to carefully compare its appearance and dimensions with the photographs in the gallery or ask a question on the forum https://www.mikroskopie-forum.de/

Description of this part for the microscope.

particular screw was removed from a Zeiss Standard 14 microscope, but it will most likely fit most models of the Standard series, for example:
- Zeiss Standard GFL
- Zeiss Standard 16
- Zeiss Standard WL 89
- Zeiss Standard Universal
- Zeiss Standard Photomicroscope
- Zeiss Ultraphot

Note - over the years, Zeiss microscopes (or the same microscopes sold under the Zeiss-Winkel name or under the Opton brand), especially simpler models such as the Zeiss Standard Junior, used different types of head-centering screws. These were not necessarily this type - in some cases ordinary threaded clamping screws were used instead.

Before deciding to replace the screw in a microscope, it is best to carefully compare its appearance and dimensions with the photographs in the gallery or ask a question on the forum https://www.mikroskopie-forum.de/

In the last photos in the gallery, I use arrows to show exactly which microscope component is being offered and where it is in the microscope located .

Description of this part for the microscope.

field lens (Zeiss P/N 47 30 68). It can be installed in the tube between the objective nosepiece and the observation head. The lens is operated by a lever protruding from the side of the tube. In the manufacturer's documentation, this lever is referred to as "Switch to turn axis, e.g. with wide field changer 0.8x-1x". If this optional microscope component is not installed, the opening intended for the lever is closed with a plastic blanking plug additionally secured by a retaining screw. This listing includes exactly that end cap and screw.

This particular cover was removed from a Zeiss Standard 14 microscope, which is not normally equipped with the lever-operated lens. However, it will most likely fit the majority of other Standard series models, for example:
- Zeiss Standard GFL
- Zeiss Standard 16
- Zeiss Standard WL 89

The blanking plug itself carries the catalog number Zeiss 47 30 65 (alternative notation: Zeiss 473065) and is described as an "intermediate tube cover element".

Not only is this plastic cap frequently lost over the years, but the lever itself or the lens assembly may also become damaged and require removal. In such cases, this blanking plug should be installed to protect the microscope optics from dust.

In the last photographs in the gallery, I use arrows to show exactly which microscope component is being offered and where it is located within the microscope.

Description of this part for the microscope.

35 160/0.17
Manufacturer part number: 46 05 10-9906 (alternative notation: 460510 - 9906)
Color correction: Planachromat
Numerical aperture N.A.: 0.35
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm thickness
Immersion: no (dry objective)
Thread: RMS

Description of this part for the microscope.

65 160/0.17
Manufacturer part number: 46 07 10-9904 (alternative notation: 460710 - 9904)
Color correction: Planachromat
Numerical aperture N.A.: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0.17 mm thickness
Immersion: no (dry objective)
Thread: RMS

Description of this part for the microscope.

supply:
Manufacturer: Carl Zeiss
Model: VWH 200/C 250 f-3b
Manufacturer P/N: 39 26 34 (also written as 392634)
Supported fluorescence lamps: HBO 200 W/4 L1, HBO 200 W/4 L2 and CSI 250W
Input voltage: 220 V - 240 V
Power rating: 900 VA

This power supply was supplied as standard with Zeiss Photomicroscope microscopes (commonly known as the Zeiss Phomi) whenever the microscope was equipped with an HBO high-pressure fluorescence illuminator (also referred to as a burner or lamp).

The same or very similar illuminators with identical electrical specifications were used in, among others:
- Zeiss Standard WL
- Zeiss Photomicroscope
- Zeiss Universal
- Zeiss Ultraphot
- such illuminators were also occasionally adapted for use with other microscope models, including those made by other manufacturers
Therefore, this power supply is suitable for all of the applications listed above.

Please note: the last photograph shows a dent in the housing. This does not affect the operation of the unit. Since the dent is located on the underside of the housing, it is not visible when the power supply is standing on a laboratory bench.

IMPORTANT: Always protect your eyesight when working with UV illumination. Never exceed the recommended service life of HBO high-pressure lamps. Always follow the operating instructions supplied with the fluorescence illuminator.

Description of this part for the microscope.

Zeiss Universal
- Zeiss Photomicroscope (the so-called Zeiss Phomi)
- Zeiss Ultraphot

This holder allows interchangeable microscope stages to be mounted, meaning stages that are not screwed directly to the microscope stand. It also features two centering screws.

This holder consists of two parts:
- the so-called stage "support", which is mounted onto a dovetail guide using a quick-release clamping mechanism
- and the circular stage holder attached to it

If this circular holder for the interchangeable stage is removed, other microscope stages that are not interchangeable but instead mounted with four screws can be attached to the "support".

The image gallery contains detailed photographs of this part together with its dimensions.
In the last photograph, an arrow indicates where this part is located inside the microscope.

Additionally, the video gallery contains two videos: the first presents this part from different angles, in close-up views, and demonstrates the movement of its moving components, while the second video shows, among other things, how this part is removed from the microscope body using a Zeiss Photomicroscope II as an example.

The Zeiss Universal, Zeiss Ultraphot, the earliest versions of the Zeiss Standard WL, and the first model of the Zeiss Photomicroscope were originally factory-equipped with this component in black.

The Zeiss Photomicroscope II, Zeiss Photomicroscope III, and the later versions of the Zeiss Standard WL were factory-equipped with this component in grey.

The colour of this component has no effect on compatibility. In other words, a component of either colour fits all of the microscope models listed above.

The component presented here is grey.
If you're looking for the gray version, it's listed in this database under number 99607.

Description of this part for the microscope.

called Zeiss Phomi)
- Zeiss Standard WL 89
- Zeiss Universal
- Zeiss Ultraphot (although the original holder in this model is black)

This complete module consists of the following parts:
- the section with the condenser focusing knob for height adjustment, mounted onto a dovetail guide using a quick-release clamping mechanism
- the condenser holder with a toothed rack, condenser retaining screw and two centering screws
- a swing-out holder for a 32 mm round filter
- a swing-out wide field lens used to provide even illumination of the specimen when observing with low-magnification objectives

This holder accepts condensers with a dovetail mount - it is not intended for condensers with a diameter of 37 mm or 39.5 mm.

The image gallery contains detailed photographs of this part together with its dimensions.
In the last photograph, an arrow indicates where this part is located inside the microscope.

Additionally, the video gallery contains two videos: the first presents this part from different angles, in close-up views, and demonstrates the movement of its moving components, while the second video shows, among other things, how to remove this condenser holder from the microscope body using a Zeiss Photomicroscope II as an example.

The Zeiss Universal, Zeiss Ultraphot, the earliest versions of the Zeiss Standard WL, and the first model of the Zeiss Photomicroscope were originally factory-equipped with this component in black.

The Zeiss Photomicroscope II, Zeiss Photomicroscope III, and the later versions of the Zeiss Standard WL were factory-equipped with this component in grey.

The colour of this component has no effect on compatibility. In other words, a component of either colour fits all of the microscope models listed above.

The component presented here is grey.
If you're looking for the gray version, it's listed in this database under number 99606.