Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

Dovetail/mounting connector for the microscope body
- Dovetail connector diameter: 43 mm
- Lower bottom lens

Here is the same part, but with screws.

Sorry, I don't know the part number. It's a binocular head mounted on Carl Zeiss Standard 14 and Standard 16 microscopes.

Description of this part for the microscope.

components.

Description of this part for the microscope.

diameter: 23.2 mm

Due to their very high quality, they are often used with microscopes from other manufacturers, especially when Carl Zeiss Jena Planachromat objectives are mounted.

8x eyepieces are best suited for microscopes equipped with a head with a magnification of 1.5x or 1.6x. In such cases, using 10x or higher eyepieces can result in excessive magnification and sometimes poor image quality. In such cases, 8x eyepieces provide the best image and optimal magnification.

Description of this part for the microscope.

Zeiss IM 35 (IM-35, IM35) microscope is the Opton ICM 405 (ICM-405, ICM405).

Please note that exactly the same (!) illuminator is also used on the Zeiss Standard / Photomicroscope series microscopes. Please refer to the description of illuminator No. 99684 in this database. YES – these are exactly the same illuminators. However, that particular unit was removed from a Zeiss Photomicroscope II and therefore has its own separate description. You will also find additional photographs and an extended description there.

Description of this part for the microscope.

and Standard 16 models. Does it also fit the Junior / WL / Universal and Phomi?

Description of this part for the microscope.

Standard 14 microscope

I apologize, but I don't know the P/N number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads - but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads - but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

P/N number for the head. It's the binocular head used on Carl Zeiss Standard 14 and Standard 16 microscopes. I noticed it also fits other Zeiss heads?but it definitely doesn't fit the 473012-9902.

Description of this part for the microscope.

Dovetail/mounting connector for the microscope body
- Dovetail connector diameter: 43 mm
- Lower bottom lens

Here is the same part, but without the screws.

Sorry, I don't know the part number. It's a binocular head mounted on Carl Zeiss Standard 14 and Standard 16 microscopes.

Description of this part for the microscope.

transmitted or reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: PZO
Model: K15x
Magnification: 15x
Image: micrometer and X-crosshair
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide. The entire unit is housed in an original wooden box.

The kit includes a slide with a standard micrometer scale to calibrate this eyepiece at any magnification.

Identical K15x eyepieces were also made by other manufacturers, such as Lomo and Carl Zeiss Jena.

Description of this part for the microscope.

mm
Focal Length: 45 mm
Cover Glass: No
Immersion: No
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS

This is an oil-immersion objective with a high numerical aperture. It is recommended for working with fluorescent light or for those whose primary magnification is around 40x, 45x, 50x, 55x, 60x, or 63x and who want to achieve the highest possible quality and detail visibility.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Meopta
Model: H8x M10
Magnification: 8x
Image: micrometer
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

2 mm

6x (and 8x) eyepieces are best suited for microscopes equipped with a head with a magnification of 1.5x or 1.6x. In such cases, using 10x or higher eyepieces can result in excessive magnification and sometimes poor image quality. In such cases, 6x/8x eyepieces provide the best image and optimal magnification.

Description of this part for the microscope.

Description of this part for the microscope.

Description of this part for the microscope.

23.2 mm

Compensating 5x eyepieces are very often used as projection eyepieces for microscope photography.

Description of this part for the microscope.

Description of this part for the microscope.

microscopes from other manufacturers, especially when Carl Zeiss Jena Planachromat objectives are mounted.

Description of this part for the microscope.

eyepiece contains two lines in the field of view used for adjusting DIC interference fringes, but this is the only difference compared to an otherwise identical eyepiece used for adjusting phase contrast. Therefore it can be used:
- for adjusting DIC
- for adjusting phase contrast
- for observing the iris diaphragm
- for observing the filament when setting illumination according to the Köhler standard

This is one of those microscope elements for which many different names are used. Among others:
- phase telescope
- phase contrast telescope
- phase alignment telescope
- phase adjustment telescope
- phase centering telescope
- phase contrast centering telescope
- phase contrast alignment telescope
- phase contrast adjustment telescope
- centering telescope
- condenser centering telescope
- condenser alignment telescope
- condenser adjustment telescope
- alignment telescope
- adjustment telescope
- inspection telescope
- aperture viewing telescope
- back focal plane viewing telescope
- auxiliary microscope
- phase contrast auxiliary microscope
- alignment auxiliary microscope
- centering auxiliary microscope
- adjustment auxiliary microscope
- auxiliary telescope
- centering scope
- alignment scope
- phase scope
- phase viewer
- phase contrast viewer
- phase centering eyepiece
- phase contrast eyepiece
- phase alignment eyepiece
- phase telescope eyepiece
- centering eyepiece
- condenser centering eyepiece
- adjustment eyepiece
- inspection eyepiece

Description of this part for the microscope.

transmitted or reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Model: D42 15x
Magnification: 15x
Image: micrometer and X-crosshair
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Identical K15x eyepieces were also made by other manufacturers, such as Lomo and PZO.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

Note that there are two such guides in the stage. They are made of a soft, thin piece of brass sheet and are often damaged; the bearing rollers also frequently fall out of them.

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

cover.

This microscope part was removed from a Zeiss microscope stage on which no model designation was provided. Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example Zeiss P/N 47 34 28 - 9901 https://www.microscopeparts.eu/microscope/282). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

microscope stage. Both are the same, and there's no difference between right and left. This knob moves the worm shaft (link: https://www.microscopeparts.eu/part/99272). The specimen holder carrier (link: https://www.microscopeparts.eu/part/99273) is mounted on this shaft and moves the specimen holder sideways (lateral movement).

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions.

Description of this part for the microscope.

main plate (forward-backward, i.e. longitudinal movement). There are two such knobs in the microscope stage, and the right and left are different. This is the left knob.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

main plate (forward-backward, i.e. longitudinal movement). There are two such knobs in the microscope stage, and the right and left are different. This is the right knob.

This microscope part was removed from a Zeiss P/N 47 34 28 - 9901 (473428-9901). Over the years during which Zeiss produced such stages, numerous variants were created (I have personally seen five, for example https://www.microscopeparts.eu/microscope/281). Despite this variety, the construction is largely consistent, and most parts are identical.
It is therefore highly likely that the part shown and offered here is compatible with many variants of such microscope stages.

Such stages are interchangeable and can be installed in many Zeiss microscopes, however they are most commonly used in the following microscopes:
- Zeiss Standard 14
- Zeiss Standard 16
- Zeiss Standard GFL

Also often in:
- Zeiss Standard WL
- Zeiss Standard Universal

In the photo gallery there are detailed photos of this element together with the dimensions. Additionally, in the last photo an arrow indicates which element is being referred to and where it is located, in order to clearly identify this part.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: micrometer
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: none
Mounting diameter: 23.2 mm

There is no measuring scale glass inside the eyepiece. Any 19mm diameter glass can be inserted inside, for example, with a crosshair, micrometer, or reticle.

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

08 160/-
Color correction: Planachromat
Numerical aperture: 0.08
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

Description of this part for the microscope.

Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: no
Thread: RMS
Info: Ph = phase contrast

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

mm
Focal Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: Ph3 = phase contrast

It can be used with any microscope from any manufacturer, along with a compatible phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

9904
Magnification: 10x
Correction: achromat
Numerical aperture: 0.22
Tube length: 160 mm
Focal length: 45 mm
Cover glass: indifferent
Immersion: no
Thread: RMS
Ph1: phase contrast

This specific unit was used in an inverted Zeiss ID 02 microscope, but I have also seen this objective model in Zeiss KF-2 ICS and Zeiss Axiostar microscopes.

Objectives with such low magnification (here 10x) can be used without a cover glass, with a cover glass, or for observation through thicker glass (e.g. through a Petri dish), therefore they can be used both in upright and inverted microscopes.

It can be used with any microscope from any manufacturer together with a compatible phase contrast condenser (or slider with phase rings). Of course the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

10x
Correction: Achromat
Numerical aperture: 0.24
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS
Info: PI = polarization-interference objective (red ring).

Compatible with the following PZO condensers:
- PZO KPI 2
- slit condenser
PI objectives are among the components of the PZO UPI set (i.e. the so-called DIC).

VERY IMPORTANT: the marking on the objective is "PI" (in lowercase: "pi"), meaning [P]-polarization [I]-interference.
In many descriptions available on the Internet, you can find information that this is a PLAN objective. This is an ERROR caused by misinterpreting the marking as PL.

Note: another INCORRECT piece of information often found online is that these are DIC objectives. This is not true.
DIC according to Pluta (niem: DIC nach Pluta), sold by PZO, achieves the DIC effect (i.e. a 3D relief image) using standard achromatic PZO objectives (and not only those). Objectives marked PI with a red ring are not required for this.

It can be used with any microscope from any manufacturer that supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

10 160/-
Color correction: Planachromat
Numerical aperture: 0.10
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Color correction: Planachromat
Numerical aperture: 0.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.32
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 1,25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: HI = Homogene Immersion, also oil immersion

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

eyepieces can be used with microscopes from any manufacturer, as long as the microscope supports eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

microscopes from any manufacturer, as long as the microscope supports eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.