Home page of the microscope service parts, repair and spare parts online catalog - Sermik-Oplatek Mikroskopservice Dresden f.n.n.Z

Description of this part for the microscope.

160 mm
Focal Length: 45 mm
Cover Glass: no
Immersion: no
Thread: RMS
Info: Phv = phase contrast variable

It can be used with any microscope from any manufacturer, along with a compatible Phv phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

numbers. This microscope element bears the number 2480 (full designation: Si10 2480).

Inside there is a classic mirror reflecting light and a matte mirror diffusing light. Both are in very good condition.

Note - this base does not fit the first models of Carl Zeiss Jena Technival and Citoval stereomicroscopes, as they have a smaller stand foot.

The complete factory set consists of:
- transmitted light base
- wrist supports
- light source
Here I present and offer only the base - without wrist supports and without the light source.

Description of this part for the microscope.

transmitted light is inserted. Inside there is a lens that collimates the light beam. In the lower part of this element there are three filter holders and a shutter that allows complete cutoff of this light source.

The illumination block in the Carl Zeiss Jena Fluoval-2 fluorescence microscope is modular, and each of its elements can be easily detached and attached. This microscope element is mounted to the whole module using screws and the key https://www.microscopeparts.eu/part/00588.

Description of this part for the microscope.

micrometer scale: no
- dedicated for polarization: no
- material: brass
- mounting diameter: 71 mm

This stage fits the following microscopes:
- Carl Zeiss Jena L-Stativ
- Carl Zeiss Jena Lg
- Carl Zeiss Jena Lu
- Carl Zeiss Jena Lr
- Carl Zeiss Jena Lumipan

This Carl Zeiss Jena stage also fits microscopes:
- Lomo MBI-1
- Lomo MBR-3
- Lomo Biolam
- Lomo sold under the names Bresser and Zenith

If any of the above microscopes currently has a fixed stage (screwed), it is possible to retrofit a holder for interchangeable stages ( like this: https://www.microscopeparts.eu/part/99175) - this applies to both Carl Zeiss Jena and Lomo microscopes.

From the 1930s to approximately the mid-1960s many German manufacturers produced microscopes with the same stage mounting standard, so this stage will also fit them.

How does compatibility of stages between Carl Zeiss Jena and Lomo microscopes work?
- Carl Zeiss Jena stages for L-Stativ microscopes have a mounting diameter of 71 mm
- Lomo stages for MBR-3 / MBI-1 microscopes have a mounting diameter of 73 mm
- The spring-loaded front screw and long side centering screws in the mounting holder compensate for these differences
- Carl Zeiss Jena stages are more solid, heavier, made of brass
- Lomo stages are lighter, made of aluminium with plastic elements

Note that although this is a round and rotating stage, it is not a polarizing stage. It does not have a micrometer scale to read how many degrees (0-360) the rotation has occurred. Without this scale it can of course be used for amateur observations in polarized light, however for professional applications this is disqualifying.

Description of this part for the microscope.

Carl Zeiss Jena Nf
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena NU / NU2

This lens DOES NOT FIT grey pancratic condensers from the following microscopes:
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Docuval

IOR Bucuresti and Lomo produced their own versions of pancratic condensers - I do not know whether this lens is compatible with them.

Description of this part for the microscope.

black Carl Zeiss Jena microscopes
- Nf
- Ng
- Lg
- Lr
- Lu
- Lumipan

as well as newer, gray Carl Zeiss Jena
- Ergaval
- Amplival
- Fluoval
- Epival
- Interphako
- Vertival
- and other variants

and
- Lomo Biolam
- Bresser Biolam
- Lomo MBB-1A
- Lomo MBI-1
- Lomo MBR-3
- and some IOR Bucuresti

have an interchangeable objective turret.

This is an excellent solution for owning, using, and quickly replacing entire sets of objectives.

For example, you can have separate turrets already equipped with a complete set of objectives:
- low magnification for observing macro objects with side illumination, without a cover glass (e.g., 2.5x / 3.2x / 5x / 8x / 10x)
- for phase contrast
- for various phase contrasts (positive, anoptral, amplitude, Zernike)
- for DIC
- for water immersion (e.g., Lomo)
- all for oil immersion (e.g., Leitz 10x Oil / 25x Oil / 40x Oil / 100x Oil)
- apochromatic for better color
- for polarization
- only high magnifications, e.g., for analyzing cell wall ornamentation (50x / 63x / 80x / 100x)
- for darkfield work (objectives with an iris diaphragm in the center)

Therefore, having only one microscope we can use it for different purposes and not screw in and unscrew all the lenses manually each time.

This is the newest, matte version of the objective revolver. If you're looking for the glossy version, see here: https://www.microscopeparts.eu/00736.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: micrometer
Mounting diameter: 23.2 mm

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

reflected light microscopes, as long as the eyepiece mounting diameter on the microscope head is 23.2 mm.

Manufacturer: Carl Zeiss Jena
Magnification: 7x
Image: none
Mounting diameter: 23.2 mm

There is no measuring scale glass inside the eyepiece. Any 19mm diameter glass can be inserted inside, for example, with a crosshair, micrometer, or reticle.

The eyepiece features diopter adjustment and image sharpness adjustment on a micrometer slide.

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

rare on the used microscope market. It can be used with microscopes such as:
- Carl Zeiss Jena Jenamed Fluorescence (Fluoreszenz)
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Laboval Fluorescence

Description of this part for the microscope.

filter holder of Carl Zeiss Jena Vertival microscopes.

Description of this part for the microscope.

160 mm
Focal Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: no
Thread: RMS
Info: Phv = phase contrast variable

It can be used with any microscope from any manufacturer, along with a compatible Phv phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

Length: 33 mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

operates in the following Carl Zeiss Jena microscopes:
- Ergaval
- Amplival
- Fluoval
- Vertival
- Epival
- Docuval
- Metaval

Instructions on how to disassemble the mechanism in the Carl Zeiss Jena Amplival / Ergaval microscope: https://www.mikroskopie-forum.de/index.php?topic=38565.0

Description of this part for the microscope.

used, for example, in microscopes from Carl Zeiss Jena of the Mikroval series:
- Eduval
- Laboval
- Ergaval
- Amplival (entire series including Epival, Vertival, Amplival-Pol)
- Fluoval
- Metaval
- Telaval
- even Epignost

In microscope models with fluorescence illumination (e.g. Laboval Fluoreszenz or Fluoval), a filter wheel is installed in this head. When the manufacturer installed this head in other microscope models - a blanking plug was placed instead of the filter wheel - and this is exactly the element shown here.

Over the years, this element is very often lost and on the secondary market there are many such photo trino adapters without the blanking plug. The lack of this blanking plug can cause even large contaminants to enter the optics.

Description of this part for the microscope.

10 160/-
Color correction: Planachromat
Numerical aperture: 0.10
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This lens provides an excellent, wide image, and because it doesn't require a cover glass, it's often used for macro photography and stacking.

Important - this lens is not suitable for taking photos using the "direct-projection" technique, as it requires plan-compensation optics.

A microscope objective with such low magnification is used, among others, in the following fields:
- tissue overview examination in pathomorphology
- observation of insects
- observation of minerals
- observation of inclusions in amber
- handwriting analysis
- observation of micromollusks
- and many others

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

Color correction: Planachromat
Numerical aperture: 0.25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.32
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 0.65
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

17
Color correction: Planachromat
Numerical aperture: 1,25
Tube length: 160 mm
Focal length: 45 mm
Cover glass: yes, 0,17 mm
Immersion: yes, oil
Thread: RMS
Info: HI = Homogene Immersion, also oil immersion

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, i.e. support RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

3x
Model: Semiplan 6.3/0.16 160/-
Color correction: Semi-Planachromat
Numerical aperture: 0.16
Tube length: 160 mm
Focal length: 45 mm
Cover glass: no
Immersion: no
Thread: RMS

This is one of the most commonly used microscope objectives for macro photography and focus stacking.

Important - this objective IS SUITABLE for taking images using the "direct-projection" technique, as it does not require plan-compensating optics.

It can be used with any microscope from any manufacturer. Of course, the microscope must be compatible, meaning it supports RMS objectives, TL=160 mm, FL=45 mm.

Description of this part for the microscope.

(and its variants: Fluoval, Epival, Vertival)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

Both the left and the right knob are identical, but when installing be careful about the screw length, as they may differ).

VERY IMPORTANT: although the right and left knobs are identical - different screws are used to attach them.

Lengths of screws used to attach the knobs in Carl Zeiss Jena Ergaval and Amplival microscopes:
- left fine adjustment knob (micro): 1 pc. screw 12 mm
- left coarse adjustment knob (macro): 3 pcs. screws 8 mm
- right fine adjustment knob (micro): 1 pc. screw 16 mm
- right coarse adjustment knob (macro): 3 pcs. screws 12 mm

Over the years these plastic knobs are often damaged:
- sometimes they crack due to impact or improper transport securing
- often they are partially melted by a soldering iron, light bulb or even a cigarette
- sometimes they are damaged during attempts to remove them

Description of this part for the microscope.

Amplival (and its variants: Fluoval, Epival, Vertival)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

Both the left and the right knob are identical, but when installing be careful about the screw length, as they may differ).

VERY IMPORTANT: although the right and left knobs are identical - different screws are used to attach them.

Lengths of screws used to attach the knobs in Carl Zeiss Jena Ergaval and Amplival microscopes:
- left fine adjustment knob (micro): 1 pc. screw 12 mm
- left coarse adjustment knob (macro): 3 pcs. screws 8 mm
- right fine adjustment knob (micro): 1 pc. screw 16 mm
- right coarse adjustment knob (macro): 3 pcs. screws 12 mm

Over the years these plastic knobs are often damaged:
- sometimes they crack due to impact or improper transport securing
- often they are partially melted by a soldering iron, light bulb or even a cigarette
- sometimes they are damaged during attempts to remove them
- sometimes, when the grease has dried out, the user tries to move the knob using pliers and damages it

Description of this part for the microscope.

an integrated gear for adjusting the height of the microscope condenser, as well as a rack with the element on which the condenser holder is mounted.

Description of this part for the microscope.

The photos show the exact dimensions of this item.

Description of this part for the microscope.

06 oo/-A
Magnification: 3.2x
Numerical aperture N.A.: 0.006
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: not required, may be present or not
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

25 oo/-A
Magnification: 12,5x
Numerical aperture N.A.: 0.25
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: not required, may be present or not
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

17-A
Magnification: 25x
Numerical aperture N.A.: 0.50
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: yes, 0,17 mm
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

17-A
Magnification: 40x
Numerical aperture N.A.: 0.65
Optical correction: planachromatic
Additional: "GF" = Grossfeld, meaning a wide field objective
Tube length: infinity
Thread: M25
Cover glass: yes, 0,17 mm
Immersion: no

This objective fits, among others, the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenalab
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar

For the Carl Zeiss Jena Jenamed microscope, this objective fits every variant:
- Carl Zeiss Jena Jenamed variant
- Carl Zeiss Jena Jenamed Fluorescence
- Carl Zeiss Jena Jenamed hematology
- Carl Zeiss Jena Jenamed cytology
- Carl Zeiss Jena Jenamed 2

The best image quality and full performance of this objective are achieved when using a Carl Zeiss Jena microscope head supporting 30 mm eyepieces and eyepieces marked "GF", meaning - similarly to the objectives - wide field eyepieces.

An interesting fact is that I very often see this objective (as well as other Carl Zeiss Jena objectives with M25 thread) mounted in Leica microscopes (for example Leica DMLB or Leica DMLS). Carl Zeiss Jena objectives are slightly shorter than Leica ones, so users apply extension adapters in such cases.

Description of this part for the microscope.

holder into which a round filter with a diameter of 32 mm can be inserted
- the hinged, tilting cover allows the light output to be completely blocked

This slide-in element is used in the following microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Cast or injection-molded metal parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the numbers 2645 (full designation: Si10 2645) and 2683 (full designation: Si10 CZ 2683).

By default, in the basic versions of the CZJ Jenaval microscope, a simpler version of this element is installed - only a slide with a filter holder, without a light blocking cover.

In models with EPI illumination (de: Auflicht), such as Carl Zeiss Jena Jenavert and Carl Zeiss Jena Jenalumar, the transmitted light illuminator cover allows the transmitted light to be completely shut off when working exclusively with EPI illumination.

In the last photo in the gallery, the exact location of this element in the microscope is indicated with an arrow. This allows you to identify it precisely.

Description of this part for the microscope.

Mounting method: screw-mounted

Note: this nosepiece does not fit the Carl Zeiss Jena Jenalumar microscope. Although most components between these models are interchangeable - the objective nosepiece is not.

Cast or injection-molded metal parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the number 2643 (full designation: Si10 CZ 2643).

Description of this part for the microscope.

microscopes:
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenavert

Cast or injection-molded metal parts of Carl Zeiss Jena carry their own numbers. This microscope element bears the number 2645 (full designation: Si10 2645).

In the last photo in the gallery, the exact location of this element in the microscope is indicated with an arrow. This allows you to identify it precisely.

Description of this part for the microscope.

Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the left clamp, which does have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

commonly used in microscopes with a 30 mm eyepiece mounting diameter:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older microscopes of the Mikroval series (e.g. Ergaval and Amplival) - in such cases this eyepiece will also fit them, because - in general - eyepieces fit the head mounted on the microscope, not the microscope itself.

A single Carl Zeiss Jena PW 6.3x (25) eyepiece can solve the following problems:
- a second 6.3x eyepiece is missing to complete a pair
- a low magnification eyepiece is needed for use in a trinocular photo tube

Description of this part for the microscope.

commonly used in following microscopes:
- Carl Zeiss Jena Technival / Technival-2
- Carl Zeiss Jena Citoval / Citoval-2

Although such eyepieces were most commonly used in stereoscopic microscopes, they are often also used in biological microscopes, e.g. Carl Zeiss Jena Ergaval or Carl Zeiss Jena Amplival. This eyepiece is compatible with almost any microscope from any manufacturer, provided that the microscope head supports eyepieces with a mounting diameter of 23.2 mm.

Description of this part for the microscope.

microscopes:
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the right clamp, which does have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

Carl Zeiss Jena Amplival
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval
- Carl Zeiss Jena Fluoval

On a mechanical microscope stage there are two such clamps, between which a microscope slide with a specimen is placed. These clamps - right and left are not identical. Here I present and offer the left clamp, simple, which does NOT have a spring.

Note - different stage models use different clamps. In the photo gallery there are detailed photos of this element along with dimensions. In the last photo, the stage to which this clamp fits is shown. Additionally, an arrow indicates where this element is located, so it is clear which part of the microscope stage is being referred to.

Description of this part for the microscope.

meaning the shaft with focusing knobs mounted on both ends on the sides of the microscope. Part of this shaft contains a toothed rack, or more precisely speaking, it is a toothed shaft. In the item shown and offered here, the fine focus knob (micro focus) is mounted on the left end of the shaft. Please note that the left and right knobs are identical - however, screws of different lengths are used to attach them: the left knob is attached with a 12 mm screw, while the right knob uses a 16 mm screw. Detailed information about the screws used to attach the coarse and fine focus knobs can be found here: https://www.facebook.com/MikroskopyPZO/posts/pfbid0x2tFPHAEqjn4B7BRsvm2vAt9yyuuSM836QS6K4951GqeUFpU2FJH8YXfFFxbz3cPl

Such focus shafts are used in the following microscopes:
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival (and its variants: Fluoval, Epival, Vertival, Interphako)
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Docuval

This coarse and fine focus shaft may help solve the following problems in Carl Zeiss Jena Ergaval / Amplival microscopes and related models:
- if the shaft became bent, causing a noticeable jump while rotating it (a very common failure)
- if the screw holding the fine focus knob broke off or snapped, leaving part of the screw inside the shaft
- if the left fine focus knob is missing or damaged
- if the thread on the right or left end of the shaft, where the fine focus knobs are attached, is damaged
- if the toothed rack on the shaft (because such a shaft is effectively a toothed shaft) becomes damaged

Description of this part for the microscope.

for taking microscope photographs or recording microscope videos. This is a gray photographic adapter.

Basic technical parameters:
- mounting connection to microscope stand: 41 mm dovetail
- output connection type on the photo port: 49 mm internal thread
- connection for binocular head mounting: Jena standard 41 mm dovetail
- magnification directed to the binocular head: 1.6x
- magnification on the photo output: none (that is 1.0x)

Because this photo head has a 49 mm threaded output, virtually any device, camera, adapter, tube or other accessory can be connected after using an appropriate 49 mm thread adapter. Direct projection technique may be used (because there is no additional optics inside), or any projection eyepieces may be installed in the optical path.

This photographic attachment is intended mainly (but not exclusively) for the following microscope models:
- Carl Zeiss Jena Eduval
- Carl Zeiss Jena Laboval
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Metaval
- Carl Zeiss Jena Telaval
- Carl Zeiss Jena Pictoval
- Carl Zeiss Jena Epignost

The list above contains Mikroval series microscopes with gray housings - just like the tube shown and offered here. However, it also works with older black Carl Zeiss Jena microscopes:
- Carl Zeiss Jena L-Stativ (models Lg, Lu and Lr)
- Carl Zeiss Jena Lumipan
- Carl Zeiss Jena Ng
- Carl Zeiss Jena Nf (and NfPk)

Please note that microscopes from other manufacturers also use the 41 / 41.5 mm dovetail connection standard. Because of this, this photographic head can also be used with microscopes made by:
- Lomo (for example Lomo Biolam)
- Meopta
- IOR
- selected Reichert microscopes (for example Reichert Neozet)
- Will Wetzlar
- Hund Wetzlar
- Leitz Wetzlar

This Carl Zeiss Jena tube is also very often used with microscopes having a larger head mounting diameter. In such cases users apply additional spacer or thickening rings. Because of this, this photo adapter also fits microscopes from manufacturers such as:
- PZO (for example the PZO Biolar model with 43 mm connection)
- Olympus (for example the Olympus CH model with 42 mm connection)

The element that allows a photographic camera or imaging camera to be connected to Carl Zeiss Jena Mikroval series microscopes may be referred to by different names. Commonly used names include:
- trino head
- trinocular head
- photo head
- photographic head
- photo attachment
- photographic attachment
- photo adapter
- photographic adapter
- photo tube
- photographic tube
- phototube
- photographic angle tube
- and various combinations of the words head, attachment, adapter or tube with terms such as photo, photographic, for camera and similar

Description of this part for the microscope.

related models.

This element is used when the microscope does not have a transmitted light illuminator with a lamp holder installed in the rear part of the base. In such a case, so that there is no open hole and no contamination can enter the inside of the microscope, this opening can be closed with this blanking plug.
When can such a situation occur that the microscope does not have a transmitted light illuminator? Most often when the microscope is intended for reflected light work only and simply does not have any DIA illuminator (transmitted light illuminator).

This element fits the following microscopes:
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Interphako
- Carl Zeiss Jena Fluoval

The photo gallery contains detailed photos of this element from different sides, while the video (in the video gallery) shows exactly how this blanking plug is used and where it is mounted.

Description of this part for the microscope.

and related models.

This element is used when transmitted light is temporarily not needed. The illuminator itself does not need to be removed - instead, the light output should simply be completely blocked, and this light output is the collector lens itself. This collector lens is located inside the microscope base, above the angle mirror and below the condenser.

When can there be a need to completely block transmitted light? Most often when:
- a microscope with DIA illumination (transmitted light) and EPI illumination (reflected light) is available, but temporarily only reflected light operation is needed
- a microscope previously working with transmitted light (for example Carl Zeiss Jena Amplival) is being converted into a microscope intended to work permanently only with reflected light (for example converting an Amplival into a Vertival)
- for example a Fluoval microscope is used and it is undesirable that "the lower light is visible"

This element fits the following microscopes:
- Carl Zeiss Jena Ergaval
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Interphako
- Carl Zeiss Jena Fluoval
- Carl Zeiss Jena Docuval

The photo gallery contains detailed photos of this element from different sides, while the video (in the video gallery) shows exactly how this blanking plug is used and where it is mounted.

Description of this part for the microscope.

models.

This element is used when the microscope does not have an EPI illuminator (reflected light illuminator). In such a case, so that there is no open hole and no contamination can enter the inside of the microscope, this opening can be closed with this blanking plug.
When can such a situation occur that the microscope does not have a reflected light illuminator? Most often when the microscope is intended exclusively for transmitted light work and simply does not have any EPI illuminator.

This element fits the following microscopes:
- Carl Zeiss Jena Amplival
- Carl Zeiss Jena Epival
- Carl Zeiss Jena Vertival
- Carl Zeiss Jena Interphako
- Carl Zeiss Jena Fluoval

It should be noted that it is not possible to mount this blanking plug in the Carl Zeiss Jena Ergaval microscope - this model is simply a lower model than the Amplival and does not have the option of connecting an EPI illuminator.

The photo gallery contains detailed photos of this element from different sides, while the video (in the video gallery) shows exactly how this blanking plug is used and where it is mounted.

Description of this part for the microscope.

, DIC or polarizing
- iris diaphragms

Often compatible with microscopes from other manufacturers.

Description of this part for the microscope.

Length: 45 mm
Cover Glass: yes, 0,17 mm
Immersion: no
Thread: RMS
Info: Phv = phase contrast variable

It can be used with any microscope from any manufacturer, along with a compatible Phv phase contrast condenser. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 45 mm.

Description of this part for the microscope.

mm
Cover Glass: 0.17 mm
Immersion: no
Thread: RMS

It can be used with any microscope from any manufacturer. The microscope must be compatible, meaning it supports RMS objectives, TL = 160 mm, FL = 33 mm.

After installing the 12 mm adapter, this objective lens will have FL = 45 mm.

The fact that this objective has FL = 33 mm allows it to be used with microscopes from other manufacturers, including:
- Lomo Biolam
- Lomo MBB-1A
- PZO MB-10
- Olympus CH

Description of this part for the microscope.

Jena
Name: Grossfeld Binocular
Eyepiece mounting diameter: 30 mm
Microscope mount: 41 mm dovetail mount
Diopter adjustment: yes, for one eyepiece

The set also includes two eyepieces:
- Model: Carl Zeiss Jena GF-Pw 10x (25)
- Mounting diameter: 30 mm

This head is most commonly used in the following microscopes:
- Carl Zeiss Jena Jenamed
- Carl Zeiss Jena Jenaval
- Carl Zeiss Jena Jenalumar
- Carl Zeiss Jena Jenapol
- Carl Zeiss Jena Jenvert
- Carl Zeiss Jena Jenatech
- Carl Zeiss Jena Jenalab

Interestingly, widefield binocular heads with a 30 mm eyepiece mounting diameter are sometimes also installed in older Mikroval series microscopes (for example Ergaval and Amplival). If the microscope is additionally equipped with GF-Planachromat series widefield objectives (or GF-Planapochromat objectives used in Docuval microscopes) - this creates the best possible combination for Carl Zeiss Jena microscopes with a 160 mm tube length.

This microscope head model is identical to the Baader Mark V binocular viewer used in astronomical telescopes and is often purchased by astronomy enthusiasts and adapted for telescope mounting.

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
Carl Zeiss Jena Jenamed 2 and Jenamed Histology microscopes already use different stages.

This particular example shown and offered here was removed from a Carl Zeiss Jena Jenamed Cytology microscope.

The stage in Carl Zeiss Jena Jenamed microscopes is a flat, smooth surface permanently attached with screws to the microscope body, onto which cross table mechanisms or specimen holders are mounted - various versions depending on individual needs.

Mechanically, this stage consists of two elements:
- a smooth upper steel surface attached to the cast form underneath
- the lower cast form (with manufacturer number), which is attached to the microscope body
Both parts have an opening for the microscope condenser. The condenser is mounted from the underside of the stage (condenser available separately).

Metal cast or injection-moulded microscope parts made by Carl Zeiss Jena have their own numbers. This part carries the number 2712 (full marking: Si10 CZ 2712).

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

microscope. It will most likely also fit other models from the Jenamed series (e.g. Jenamed Variant, Jenamed Fluorescence, Jenamed-2, Jenamed Hematology). Please note however that the Carl Zeiss Jena Jenamed Histology microscope is factory-equipped with a different type of condenser - the "flip-out" type.

To make sure whether this condenser will fit a specific Carl Zeiss Jena microscope from the Jenamed series, it is best to carefully check all dimensions based on the gallery photos or ask a question on a professional forum, e.g. https://www.mikroskopie-forum.de/

Mechanically, this condenser is mounted from the underside of the microscope stage - first it is screwed into the threaded opening in the stage and then secured with three screws. The upper lens can be unscrewed to obtain a condenser with a lower numerical aperture N.A. This condenser does not have an iris diaphragm installed because in Jenamed microscopes it is a separate element.

Replacing the condenser in a Carl Zeiss Jena Jenamed microscope may be necessary:
- when the upper lens becomes damaged, for example when it turns matte due to exposure to various chemical reagents
- when the upper lens becomes damaged due to rubbing. Surprisingly, this unusual type of damage is very common after several decades of microscope use.

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

was removed from a Carl Zeiss Jena Jenamed Cytology microscope. It will most likely also fit other models from the Jenamed series (e.g. Jenamed Variant, Jenamed Fluorescence, Jenamed-2, Jenamed Hematology).

It does not fit the Jenamed Histology model because the Carl Zeiss Jena Jenamed Histology microscope features a different type of condenser (a 'flip-out' type) by default. For this reason, the iris diaphragm is located slightly lower than in other models and is different.

To make sure whether this iris diaphragm will fit a specific Carl Zeiss Jena microscope from the Jenamed series, it is best to carefully check all dimensions based on the gallery photos or ask a question on a professional forum, e.g. https://www.mikroskopie-forum.de/

Mechanically, this diaphragm is mounted underneath the condenser. The entire diaphragm module is attached to the microscope body with four screws. It is not mechanically connected to the condenser - these are separate elements. The lever pin used to open / close the diaphragm protrudes through a special opening at the front of the microscope, making it possible to adjust the diaphragm opening. This opening is located in the cover of the filter wheel - here one can see further relationships between the individual elements of the light path.

Carl Zeiss Jena Jenamed microscopes do not have a field diaphragm.

Replacement of the aperture diaphragm module in a Carl Zeiss Jena Jenamed microscope may be necessary:
- when some of the iris diaphragm blades become damaged (bent or broken)
- when the lever used to open / close the diaphragm breaks off
- when the teeth of the gear wheel mounted in this module become damaged

Metal cast or injection-moulded microscope parts made by Carl Zeiss Jena have their own numbers. This part carries the number 2713 (full marking: Si10 CZ 2713).

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

Basic parameters:
- Number of objective positions: 5
- Thread: M25
- Mounting method: integrated with a larger block attached to the microscope body using screws

Yes - the "click-stop" detent mechanism (German: Blattfeder) is included, as it is frequently damaged in this model.

Metal cast or injection-moulded parts made by Carl Zeiss Jena have their own numbers. This part carries the number: 2708 (full marking: Si10 CZ 2708).

Please note - the small block with slots for microscope sliders, attached to this revolver and bearing the number Si10 CZ 2709/2, is available separately.

In the last photo I indicate with an arrow exactly which element it is and where it is located in the microscope.

Description of this part for the microscope.

Variant, Cytology, Hematology, Histology, Jenamed-2, Fluorescence)
- Jenapol
- Jenavert
- Jenaval
- Jenatech
- Jenalumar

Please note - this is only the adjustment knob, that is the knob used by the microscope user to make the illumination brighter or dimmer. It is not a potentiometer and therefore not a part of the electrical circuit.

This knob features the characteristic white cap used on Carl Zeiss Jena microscopes, which is often lost during decades of microscope use.

Mechanically, this knob is attached to the potentiometer. The fixing screw is covered by a white metal cap.

In the last photo I indicate with an arrow exactly which element it is and where it is located in a Carl Zeiss Jena Jenamed microscope. In Jenaval and Jenalumar microscopes it is located on the microscope base.

Description of this part for the microscope.

Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

The function of this element is to reflect light coming from the microscope base vertically upwards so that, after passing through the microscope slide with the specimen and the objective, it reaches the eyepieces and ultimately the user's eyes.

Metal cast or injection-moulded parts made by Carl Zeiss Jena have their own numbers. This part carries the number: 2721 (full marking: Si10 CZ 2721).

Replacement of the angle mirror in Carl Zeiss Jena Jenamed microscopes may be necessary in the following cases, among others:
- if the mirror becomes significantly scratched as a result of improper cleaning (minor scratches are usually not visible during normal use)
- if the reflective silver coating of the installed mirror becomes oxidised
- if the mirror becomes damaged, chipped or cracked, for example after coming loose from its mount

Description of this part for the microscope.

attached to the microscope stand with screws. It serves as a mounting platform for mechanical stages, XY stage mechanisms, or specimen holders - various versions depending on the user's requirements.

Mechanically, this stage consists of two elements:
- a smooth upper steel plate attached to the cast component below
- a lower cast component (with the manufacturer's part number) attached to the microscope stand
Both parts have an opening for the microscope condenser. The condenser is mounted from below the stage (condenser available separately).

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This part is marked with number 2712 (full marking: Si10 CZ 2712).

This microscope stage DOES NOT FIT the following Carl Zeiss Jena microscopes:
- Jenamed 2
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Fluorescence

More precisely: the lower part (marked Si10 CZ 2712) is identical to the one used in other Jenamed microscope models (except Jenamed-2), whereas the smooth upper steel plate used in the Jenamed Histology differs from those used in other models by the size of the condenser cut-out (opening).

In the last photo, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

This diaphragm DOES NOT FIT the following Carl Zeiss Jena microscopes:
- Jenamed 2
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Fluorescence

Mechanically, this diaphragm is mounted below the condenser. The complete diaphragm module is attached to the microscope stand with two screws. It is not mechanically connected to the condenser - these are separate components. The lever (pin) used to open and close the diaphragm extends through a dedicated opening at the front of the microscope, allowing adjustment of the diaphragm opening. This opening is located in the cover of the filter wheel - illustrating further relationships between successive elements of the light path.

Carl Zeiss Jena Jenamed microscopes do not have a field diaphragm.

Replacement of the aperture diaphragm module in a Carl Zeiss Jena Jenamed Histology microscope may be necessary:
- when one or more iris diaphragm blades become damaged (bent or broken)
- when the lever used to open and close the diaphragm breaks off
- when the teeth of the gear wheel installed in this module become damaged

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This part bears number 2714 (full marking: Si10 CZ 2714). The iris diaphragm module used in the other Carl Zeiss Jena Jenamed microscope models bears part number Si10 CZ 2713.

Description of this part for the microscope.

therefore cannot be used in:
- Jenamed Cytology
- Jenamed Variant
- Jenamed Hematology
- Jenamed Fluorescence
- Jenamed-2

Mechanically, this condenser is a "flip-out" design and is mounted in a metal frame together with a lever used to rotate it in order to obtain one of two operating modes: low or high numerical aperture N.A. This lever extends outside the microscope housing so that the user can operate it.

The complete module is mounted underneath the microscope stage by attaching the entire condenser assembly from below with four screws. This condenser does not contain an iris diaphragm because, in Jenamed microscopes, it is a separate component mounted beneath the condenser.

In the Carl Zeiss Jena Jenamed Histology microscope, this condenser is not used together with the wide-field lens that is installed beneath the condenser in other Jenamed models (part Si10 CZ 2711-1). In the Jenamed Histology model, a polarizer is installed in this position instead.

Replacement of the condenser in a Carl Zeiss Jena Jenamed Histology microscope may be necessary:
- when the upper lens becomes damaged, for example by becoming cloudy due to exposure to various chemical reagents
- when the upper lens is damaged by friction. Surprisingly, this unusual type of damage is very common after several decades of microscope use
- when the mechanical lens switching mechanism ("flip-out") becomes damaged

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This condenser module bears number 2713 (full marking: Si10 CZ 2713).

In the last photograph, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

2 Fluorescence

It DOES NOT FIT Carl Zeiss Jena microscopes from the Jenamed series and therefore cannot be used in:
- Jenamed Cytology
- Jenamed Variant
- Jenamed Hematology
- Jenamed Histology

Mechanically, this condenser is mounted on the microscope stage support plate (stage support). The microscope stage is installed onto this support plate together with the condenser. The upper condenser lens can be unscrewed - after removing it, the condenser operates with a lower numerical aperture N.A.

This condenser does not contain an iris diaphragm because, in Jenamed microscopes, it is a separate component mounted beneath the condenser.

Replacement of the condenser in a Carl Zeiss Jena Jenamed-2 microscope may be necessary:
- when the upper lens becomes damaged, for example by becoming cloudy due to exposure to various chemical reagents (common in fluorescence applications)
- when the upper lens is damaged by friction. Surprisingly, this unusual type of damage is very common after several decades of microscope use

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. The microscope stage support plate on which the condenser is mounted bears number 3030 (full marking: Si10 CZ 3030).

In the last photograph, I indicate with an arrow exactly which component is being offered and where it is located within the microscope.

Description of this part for the microscope.

and the nosepiece is mounted from underneath.

Based on the Carl Zeiss Jena Amplival microscope, whose modular design allows for various configurations, several microscope models were created:
- Vertival
- Epival
- Amplival Interphako
- Amplival Pol
- Fluoval
and these microscopes differ from each other, among other things, by different arms. The arm from the Amplival model has the simplest construction.

By owning different arms and one microscope - you can swap them according to your needs and use different functionalities, as if you had two microscope models.

This element consists of the following components:
- fixing screw securing the arm to the microscope body
- holder enabling the mounting of components with a 41 mm mounting diameter (e.g. binocular head)
- fixing screw securing this component (e.g. head). This element is very often damaged.
- guides (slides) enabling the attachment of an interchangeable nosepiece

A device with a matching mounting diameter that is placed on the arm from above can be, for example:
- head with a built-in inclined tube
- intermediate tube (German: Zwischentubus)
- magnification changer (Optovar)
- EPI reflected light illuminator
- polarization analyzer module
- and others, because as mentioned above, the Amplival class microscopes have a modular design and there are many accessories available for them

This microscope arm can solve the following issues related to Carl Zeiss Jena Amplival class microscopes:
- if your microscope is missing this element, which happens with microscopes available on the secondary market
- if you own another variant of a microscope from this class, e.g. Carl Zeiss Jena Vertival, and you want to convert it into a "regular" Amplival
- if you own such an arm, but it is of poor quality or has damaged individual components
- if you need one of the component parts of this arm
- if you are building your own DIY project and need a mount compatible with the Carl Zeiss Jena standard

On the last photo, an arrow indicates which element it is and where it is located in the microscope to clearly identify this part.

Important: The popular and visually very similar Carl Zeiss Jena Ergaval microscope, which is often confused with the Amplival model, DOES NOT HAVE such a modular design and this arm does not fit it.

If you need any of the component parts of this arm (e.g. the large fixing screw securing the arm to the microscope stand or the smaller fixing screw securing the head to the arm - search this database or contact us by writing an email.

Description of this part for the microscope.

Amplival microscope
Number of lenses: 3
Numerical aperture N.A.: variable, from N.A. 0.16 to N.A. 1.4
Aperture diaphragm: yes, screwed on as a detachable module

The Carl Zeiss Jena pancratic condenser has three upper lenses:
- for working with low magnification objectives (usually up to 6.3x)
- Apl. 1.4 for working with high magnification objectives
- an oil immersion cardioid darkfield lens with N.A. = 1.05

Mechanically, this condenser is mounted on dovetail rails located on the microscope stage holder block.

Here are the mounting possibilities of the pancratic condenser to Carl Zeiss Jena microscopes:
- to Amplival, Docuval, Epival, Fluoval, Vertival microscopes, this condenser can be mounted directly
- to Ergaval, Nu, Nu 2, Nf microscopes, this condenser is mounted after unscrewing the aperture diaphragm from it
- to Jenaval, Jenapol, Jenalumar microscopes, this condenser can also be mounted, but it is installed together with the entire stage holder block from the Amplival microscope http://www.microscopy-uk.org.uk/mag/artfeb09/rs-jenalumar.html
- be careful, because the Lumipan microscope also features a pancratic condenser, but with a completely different mounting method

This condenser is often used as a "parts donor" for own DIY projects, for example:
- the Apl. 1.4 lens is often used to modify (upgrade) condensers with a lower numerical aperture N.A. in various microscopes
- the darkfield lens is very often used to build a standalone cardioid condenser
- the iris diaphragm has a very wide range of applications

On the last photo, an arrow indicates which element it is and where it is located in the microscope to clearly identify this part. Additionally, the attached video shows how the individual elements of this condenser move.

Description of this part for the microscope.

Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology
- Jenamed-2
- Jenamed Fluorescence

This is a microscope element placed in the microscope base. It transmits the light beam from the illuminator, unifies it (blurs the filament image using a diffuser), and then properly focuses it using a collimating lens. The light beam prepared in this way then hits an angular mirror (this is a separate element).

This microscope part is known on the secondary market among DIY enthusiasts creating their own optics projects and is frequently used by them.

Description of this part for the microscope.

Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed-2
- Jenamed Fluorescence

Important: this element is not used in the Jenamed Histology model. In this microscope version, a flip-out type condenser is used, and instead of the wide-field lens there is a polarizer. In other words - this element does not fit the Carl Zeiss Jena Jenamed Histology microscope.

This lens enables uniform illumination of the specimen when working with low magnification objectives. It is most commonly used with 3.2x and 5x objectives. It is an element installed in the microscope base and is part of the transmitted light illumination system.

Mechanically, this lens has a pin that extends outside the housing so that the user can insert or remove the lens from the optical path. It is mounted below the condenser aperture diaphragm. In Jenamed microscopes, the condenser, the aperture diaphragm, and this wide-field lens are all separate modules.

Metal cast or injection-moulded microscope parts manufactured by Carl Zeiss Jena carry their own part numbers. This condenser module bears number 2711-1 (full marking: Si10 CZ 2711-1).

Description of this part for the microscope.

following Carl Zeiss Jena microscopes:
- Jenamed Variant
- Jenamed Cytology
- Jenamed Hematology
- Jenamed Histology

This is a large module that is mechanically integrated, although it can be disassembled into smaller parts. However, if replacement becomes necessary, it is usually more convenient to replace the complete assembly. For this reason it is presented and offered here as a complete unit.

The assembly shown here includes:
- internal power supply electronics (potentiometer, transformer, etc.)
- fine focus mechanism (micro-adjustment)

If you need any individual component from this assembly, for example the transformer, a specific electronic board, only the brightness control potentiometer, or only the fine focus mechanism itself, please contact us by email.

Please note:
- the power supply is compatible with every Carl Zeiss Jena Jenamed microscope model, including Jenamed 2 and Jenamed Fluorescence
- however, the complete fine focus mechanism assembly does NOT fit Jenamed-2 and Jenamed Fluorescence, although some smaller components of the fine focus mechanism are identical across all Jenamed microscope models

This complete assembly may be required to solve, among others, the following problems in Carl Zeiss Jena Jenamed microscopes:
- when the microscope illumination does not work due to a defective power supply. This may be caused by mains voltage surges, ageing electronic components, or damage resulting from improper modifications (for example LED conversions)
- when the illumination works but brightness adjustment does not function because of a defective or worn potentiometer
- when the fine focus mechanism does not work properly, for example when the objective turret does not move upward or slowly drops by itself

It is very important to note that the internal power supply used in Carl Zeiss Jena Jenamed microscopes converts 220-240V mains voltage to 6V with a maximum power output of 25W. This power supply has the same specifications as those used in Carl Zeiss Jena Jenaval and Carl Zeiss Jena Jenalumar microscopes. If you own one of these microscopes with a defective power supply, any qualified electronics technician can transfer the electronics from a Jenamed microscope.

Description of this part for the microscope.

even though they are similar models. Carl Zeiss Jena Technival and Technival-2 microscopes use stepwise magnification switching (built-in magnification turret), while Carl Zeiss Jena Citoval and Citoval-2 microscopes feature continuously variable magnification (so-called zoom) - therefore the objectives are not interchangeable between these models.

This particular achromatic objective shown and offered here was removed from a Carl Zeiss Jena Citoval-2 microscope. Unfortunately, I am not certain whether it also fits the Carl Zeiss Jena Citoval microscope (without the "2").

For this microscope element in the Carl Zeiss Jena Citoval-2 microscope, the manufacturer uses several different names:
- Main objective (German: Hauptobjektiv)
- Objective (German: Objektiv)
- Front objective (German: Frontobjektiv)

This is the main objective of the microscope, to which an auxiliary objective (German: Vorsatzobjektiv, Vorsatzlinse, Vorsatzsystem) may optionally be attached, although this is not required.

The Carl Zeiss Jena Technival and Citoval microscopes (older version without the number "2") are grey, while the Technival-2 and Citoval-2 models are white. This objective is white and is therefore intended for the newer Carl Zeiss Jena Citoval-2 and Technival-2 stereo microscopes.

Description of this part for the microscope.

2490)
- metal plate for the base, black on one side and white on the other
- vertical steel post (stand)
- rack gear of the vertical movement mechanism
- focusing block with adjustment knobs (manufacturer's catalog name: Mikroskoptrieb 65 mm)
- holder to which the microscope body is mounted directly.
In the operating manual (https://www.mikroskop-online.de/Mikroskop%20BDA/30-725-1%20%20TECHNIVAL%202%20%20CITOVAL%202.pdf), these elements are numbered 1, 2, 3 and 35 on page 4.

Please note that the original rack gear used in Carl Zeiss Jena Citoval-2 microscopes is made of plastic and this component is very frequently damaged. If this particular element in your microscope has failed, Askania Mikroskop Technik Rathenow fortunately offers professionally manufactured brass rack gears for this microscope model (https://askania.de/products/zahnstange-messing-l-96mm).

Metal, cast or injection-moulded Carl Zeiss Jena parts carry their own identification numbers. This base (foot), into which the vertical stand post is screwed, bears the number 2490 (full designation: Si10 2490).

The Carl Zeiss Jena Technival and Citoval microscopes (older version without the number "2") are grey, while the Technival-2 and Citoval-2 models are white. This stand is white and is therefore intended for the newer Carl Zeiss Jena Citoval-2 and Technival-2 stereo microscopes.

Description of this part for the microscope.

illuminator)
Light source: 6V 25W halogen bulb, standard Narva HLWS5-A

This is a complete illuminator consisting of the following components:
- lamp housing with lenses for collimating the light beam
- light source with halogen bulb
- mounting holder for the Citoval-2 / Technival-2 microscope
In the user manual (https://www.mikroskop-online.de/Mikroskop%20BDA/30-725-1%20%20TECHNIVAL%202%20%20CITOVAL%202.pdf) these components are marked as items 7 and 8 on page 4.

Mechanically, this illuminator is mounted on an arm (illuminator holder), which can be clearly seen in the video attached to this description. This holder is attached to a special clamp located on the main objective.
The main objective of the Carl Zeiss Jena Citoval-2 / Technival-2 microscopes has two such clamps, allowing two holders and therefore two illuminators to be mounted. This allows the observed object to be illuminated from both sides. This is exactly why many users look for an additional illuminator.

This illuminator requires a transformer. It uses a 6V low-voltage halogen bulb and therefore cannot be connected directly to a mains power outlet.

The Carl Zeiss Jena Technival and Citoval microscopes (older version without the number "2") are grey, while the Technival-2 and Citoval-2 models are white. This illuminator is white and is therefore intended for the newer Carl Zeiss Jena Citoval-2 and Technival-2 stereo microscopes.

Description of this part for the microscope.

microscope objective
- Manufacturer: Carl Zeiss Jena
- Designation: Planachromat 25x/0,50 oo/0,17
- Magnification: 25x
- Numerical aperture N.A.: 0,50
- Optical correction: infinity-corrected tube length
- Optical correction class: planachromat
- Cover glass: yes, 0.17 mm
- Thread: M19

Some facts about Carl Zeiss Jena objectives with M19 thread (CZJ M19) and their compatibility with various microscopes from this manufacturer:
- these objectives are most commonly used for technical applications rather than biological applications, therefore most objectives available on the secondary market are intended for use without a cover glass (designation oo/0)
- CZJ M19 objectives intended for biological applications (designation oo/0,17) are most commonly used on Carl Zeiss Jena NU / NU2 microscopes
- in Carl Zeiss Jena Nf and Lumipan microscopes, CZJ M19 objectives are used together with an EPI illuminator
- CZJ M19 objectives can be used in Carl Zeiss Jena Polmi-A microscopes, but they provide a different magnification than the nominal value
- Carl Zeiss Jena Amplival / Amplival Pol / Amplival Interphako / Peraval microscopes feature interchangeable nosepieces, and a dedicated nosepiece for M19-thread objectives was also produced for these microscopes
- Carl Zeiss Jena Metaval and Neophot microscopes use newer versions of CZJ M19 objectives (with a coarse-knurled edge and shiny housing), although many users still experiment with older M19 objectives on these microscopes
- Carl Zeiss Jena Epignost and BK 70x50 microscopes were produced in various versions with completely different configurations - and some of them operate with CZJ M19 objectives
- Carl Zeiss Jena Vertival / Epival / Nf / BK 70x50 microscopes often allow the use of CZJ M19 objectives in EPI dark-field mode
- on the Carl Zeiss Jena Epityp-2 inverted metallurgical microscope, many users employ biological objectives designed for use with a cover glass, placing the microscope slide "upside down", with the cover glass facing downward toward the objective.